• Journal of the Korean Wood Science and Technology
• /
• 제25권3호
• /
• pp.16-23
• /
• 1997

This study was carried out to discuss feasibility of high density polyethylene(HDPE) as a new substitute for the conventional adhesives in plywood manufacture. Plywood was composed of radiata pine(Pinus radiata) and Malas(Homallium feotidium) veneers and bonded by HDPE. Adhesion characteristics and anatomical scanning has been examined through tensile-shear strength test and scanning electron microscopy(SEM). The results are as follows; 1. Optimum loading quantity was 15g/$(30.3{\times}30.3)cm^2$, and tensile-shear strength increased with the increase of loading quantity. 2. Even at the hot pressing time of 1 minute, tensile-shear strength met the value of KS(over the 7.5kgf/$cm^2$), and tensile-shear strength increased with the increase of hot pressing time. 3. Plywood composed of veneer at moisture content of 19.6% showed similar tensile-shear strength to that at air conditioned moisture content of 11.4%. 4. Under the same condition of hot pressing time, tensile-shear strength of plywood bonded by HDPE met the KS value of boil and wet test and proved the same group as phenol formaldehyde adhesive. 5. HDPE films showed mechanical adhesion through penetration into the lathe check and ray of veneer.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.152-152
• /
• 2013

Mechanism of energy conversion from chemical to electrical during exothermic catalytic reactions at the metal surfaces has been a fascinating and crucial subject in heterogeneous catalysis. A metal-semiconductor Schottky nanodiode is novel device for direct detection of chemically induced hot electrons which have sufficient energy to surmount the Schottky barrier. We measured a continuous chemicurrent during the hydrogen oxidation under of 760 Torr of O2 and 6 Torr of H2 by using Pt/Si and Pt/TiO2 nanodiodes at reaction temperatures and compared the chemicurrent with the reaction turnover rate. The thermoelectric current was measured by carrying out an experiment under O2 condition for elimination of the background current. Gas chromatograph and source meter were used for measurement of the chemical turnover rate and the chemicurrent, respectively. The correlation between the chemicurrent and the chemical turnover rate under hydrogen oxidation implies how hot electrons generated on the metal surface affect hydrogen oxidation.

• Archives of Metallurgy and Materials
• /
• 제64권2호
• /
• pp.623-626
• /
• 2019

Rare earth Nd-Fe-B, a widely used magnet composition, was synthesized in a shape of powders using gas atomization, a rapid solidification based process. The microstructure and properties were investigated in accordance with solidification rate and densification. Detailed microstructural characterization was performed by using scanning electron microscope (SEM) and the structural properties were measured by using X-ray diffraction. Iron in the form of α-Fe phase was observed in powder of about 30 ㎛. It was expected that fraction of Nd₂Fe₁₄B phase increased rapidly with decrease in powder size, on the other hand that of α-Fe phase was decreased. Nd-rich phase diffused from grain boundary to particle boundary after hot deformation due to capillary action. The coercivity of the alloy decreased with increase in powder size. After hot deformation, Nd₂Fe₁₄B phase tend to align to c-axis.

• 한국재료학회지
• /
• 제22권1호
• /
• pp.16-23
• /
• 2012

Research into the development of high strength (1 GPa) and superior formability, such as total elongation (10%), and stretch-flangeability (50%) in hot-rolled steel was conducted with a thermomechanically controlled hot-rolling process. To improve the overall mechanical properties simultaneously, low-carbon steel using precipitation hardening of Ti-Nb-V multimicroalloying elements was employed. And, ideal microstructural characteristics for the realization of balanced mechanical properties were determined using SEM, EBSD, and TEM analyses. The developed steel, 0.06C-2.0Mn-0.5Cr-0.2(Ti + Nb + V), consisted of ferrite as the matrix phase and second phase of granular bainite with fine carbides (20-50 nm) in both phases. The significant factor of the microstructural characteristics that affect stretch-flangeability was found to be the microstructural homogeneity. The microstructural homogeneity, manifest in such characteristics as low localization of plastic strain and internally stored energy, was identified by grain average misorientation method, analyzed by electron backscattered diffraction (EBSD) and hardness deviation between the phases. In summar, a hot-rolled steel having a composition 0.06C-2.0Mn-0.5Cr-0.2(Ti + Nb + V) demonstrated a tensile strength of 998 MPa, a total elongation of 19%, and a hole expansion ratio of 65%. The most important factors to satisfy the mechanical property were the presence of fine carbides and the microstructural homogeneity, which provided low hardness deviation between the phases.

• Journal of Mechanical Science and Technology
• /
• 제20권7호
• /
• pp.1002-1011
• /
• 2006

In this study, we describe the conventional hot pressing (CHP) of layered $Al-B_4C$ composites and their characterization. The matrix alloy Al-5 wt.%Cu was prepared from elemental powder mixtures. The metal and B4C powders were mixed to produce either $Al-Cu-10vol.%B_4C$ or $Al-Cu-30vol.%B_4C$ combinations. Then, these powder mixtures were stacked as layers in the hot pressing die to form a two-layered composite. Hot pressing was carried out under nitrogen atmosphere to produce $30\times40\times5mm$ specimens. Microstructural features and age hardening characteristics of composites were determined by specimens cut longitudinally. The flexural strength of both layered composites and their monolithic counterparts were investigated via three point bending tests. In the case of layered specimens of both $10vol.%B_4C$ and $30vol.%B_4C$ containing layers were loaded for three-point test. The results show that a homogeneous distribution of $B_4C$ particles in the matrix alloy which is free of pores, can be obtained by CHP method. The ageing behavior of the composites was found to be influenced by the reinforced materials, i.e. higher hardness values were reached in 8 hrs for the composites than that for the matrix alloy. Flexural strength test showed that two-layered composites exhibited improved damage tolerance depending on layer arrangement. Microstructural investigation of the fracture surfaces of the bending specimens was performed by means of scanning electron microscope (SEM). While layer with lower reinforcement content exhibited large plastic deformation under loading, the other with higher reinforcement content exhibited less plastic deformation.

• 동의생리병리학회지
• /
• 제22권3호
• /
• pp.672-677
• /
• 2008

In order to explore the anti-oxidization effect of oriental medicine and cereal medium(OCM) where Tricholoma matsutake mycelia were cultured, measurement of hot water extract and UMPM(extraction method using ultra sonic waves, micro waves, micro bubble) extract, the total polyphenol content of crude polysaccharide from each extract, SOD-like activity, electron donating ability(EDA), xanthine oxidase inhibitory activity, and tyrosinase inhibitory activity was conducted. The total polyphenol content of each extract was found to be 16.36% for hot water extract(HE) group and 15.73% for UMPM extract(UE) group and the amount of crude polysaccharide precipitated into ethanol of extracts was found to be 8.79% for UMPM ethanol extract(UEE) group and 6.48% for hot water ethanol extract(HEE) group. As a result of measurement of SOD-like activity by concentration of each extract, it was found to be 96.17% for UE group, 91.23% for HE group, 91.33% for UEE group, and 87.11% for HEE group at 20 mg/mL. In the case of EDA, it was found to be 47.55% for UE group, 44.93% for HE group, 25.38% for UEE group, and 18.36% for HEE group. And in the cases of the rates of xanthine oxidase inhibitory activity and tyrosinase inhibitory activity, as the concentration of each extract increased, the inhibition rate increased accordingly. As a result of comparison between hot water extract method and UMPM extract method using extracts obtained from oriental medicine compound medium where Tricholoma matsutake mycelia were cultured, all of the extracts were judged to have a high anti-oxidization effect. In particular, UMPM extracts were found to have higher polyphenol content, SOD-like activity, EDA, xanthine oxidase inhibitory activity and tyrosinase inhibitory activity compared to hot water extract method. In this regard, extracts obtained from OCM where Tricholoma matsutake mycelia were cultured are considered to have high availability as functional material when and if they are prepared using UMPM extract method.

• Journal of Korean Vacuum Science & Technology
• /
• 제6권2호
• /
• pp.71-75
• /
• 2002

GaAs polycrystalline thin films with good performance were prepared on conducting glass by hot wall epitaxy (HWE), which were used for solar cell. Electron probe micro-analyzer (EPMA) was applied for the composition, morphology of surface and cross-section of grown films, and X-ray diffraction (XRD) for their phase structure; Raman scattering spectum (RSS) and photoluminescence (PL) were used for evaluating their optical characteristics. The results show that, there is textured structure on the surface of grown GaAs polycrystalline films, which is greatly promised to be suitable for the candidate of solar cell with low cost and high efficiency. It is concluded that the source and substrate at temperature of 900 ~ 930 $\^{C}$ and 500 $\^{C}$ respectively would be beneficial for such films.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 추계학술대회논문집
• /
• pp.149-152
• /
• 1999

The effect of initial orientation on the microstructure and texture evolution of two ferritic stainless steels was investigated. the columnar and equiaxed crystal specimens which were prepared from continuous casting slab were hot rolled annealed cold rolled and annealed respectively. The rolling and recrystallization textures at each process stage were examined by orientation distribution function (ODF) and electron back-scattered diffraction (EBSD); The observation showed that the orientation density of the $\alpha$-fibre of hot rolled band of columnar crystal specimen was more pronounced than that of the equaxed one at the center layer. Nevertheless the cold rolled textures of Type 430 steel have demonstrated a rather similar development . Compared to Type 430 steel the development of the $\alpha$-fibre in the center layer of Type 409L steel was much more pronounced. The relation between texture evolution and ridging behaviour has been discussed.

• 한국재료학회지
• /
• 제14권7호
• /
• pp.516-521
• /
• 2004

We applied a deuterium plasma treatment to the surface of polycrystalline silicon films using PECVD and observed the change with AFM, XRD, ET-IR, and SIMS measurement. A bias temperature stressing (BTS) test was carried out to evaluate the reliability of the thin-film transistors (TFT). TFTs with channel lengths as small as 2 ${\mu}m$ were electrically stressed fer up to 1000 sec at room temperature. From the parameter variation such as s-factor, leakage current and on/off ratio, we suggest that the deuterium plasma treatment suppress the hot carrier effect and improve the stability of TFTs.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1020-1022
• /
• 2005

We have fabricated a high electron source from carbon nanotubes (CNTs) using hot-press method. Using hot-press method, we are able to control the tube density and the morphology of CNT films. We propose that the high emission current is due to the solid adhesion between the CNTs and substrates and uniform morphology of CNT film.