• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2564-2566
• /
• 2001

The reliability of EIC(Electricity, Instrumentation and Computer) systems in hot rolling mill is very important in order to maintain stable production. Signals obtained from sensors and control system should be analyzed to monitor the condition of down coiler in hot rolling mill. We develop a monitoring system of down coiler which is composed of three parts : (1) data acquisition and MMI, (2) signal processing and analyzing, and (3) automatic data saving. Also it is designed to enable to inform users the abnormal conditions of down coiler. This developed system is expected to make it possible to reduce long downtime, secure high facility precision, and maintain high control levels.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.10
• /
• pp.887-894
• /
• 2016

The CNG pressure vessel is manufactured by a deep drawing and ironing (D.D.I) process for forming cylinder parts, followed by a spinning process for formation of the dome part. However, studies on the buckling phenomenon of the dome part and formation of the inlet part have not been performed yet, and the CNG pressure vessel is produced by the experience of the field engineers and the trial and error method. In this study, buckling phenomenon during the spinning process was predicted by comparing critical buckling loads obtained through theoretical analysis with axial loads from the FEA, and a method for preventing buckling of the dome part was proposed by employing commercial software (Forge NxT 1.0.2). Also, to form the inlet part, forming loads of the roller at contact point between the roller and the dome part were analyzed according to radii of the dome part, and the inlet part was formed by controlling the radius of the dome part.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.3
• /
• pp.1105-1110
• /
• 2011

After pure titanium Ingot(G2) with 400mm in diameter was manufactured, the analysis of its ingredients showed that the oxygen content was 0.073wt% and the iron content was 0.03wt%, which made ASTM Gr.2 standardization satisfactory. The processed titanium ingot produced 42mm wire rod, and hot rolling of 18th phase produced 9mm wire rod. The hardness analysis of 15.8mm wire rod, which was processed in hot rolling of 10th phase from the surface to the center, resulted in almost constant value with Hv150~200. The last 9mm wire rod had a different yield strength and elongation percentage depending on the temperature as it was led in to a hot roller. However, tensile strength revealed an approximate value and made ASTM B863 standardization satisfactory.

• Korean Journal of Food Science and Technology
• /
• v.20 no.4
• /
• pp.504-510
• /
• 1988

The physicochemical properties of rice flours which were obtained by dry milling(blade, hammer, test and micro mill) and wet & dry milling (roller & micro mill) were investigated. The resulting flour particle sizes were reduced in the order that of blade, hammer, test, micro and roller & micro mill. Scanning electron microscopic examination showed that the starch granules were freed from the imbedding matrix as the particles became finer. The test-milled flour had the hightest levels of starch damage, maltose value and hot-water soluble amylose content, and the blade-milled flour showed the lowest levels. Amylograph viscosity and gelatinization temperature of the flours decreased as the particles became finer, and the addition of $Hg^{+2}$ increased the peak viscosity of the dry-milled flour pastes, whereas the wet & dry-milled flour did not show any changes. The blue values and ${\lambda}$max values of the iodine complex of the cold-water extractable ${\alpha}-D-glucan$ from flours were in the range of 0.023-0.029 and 518-522nm, respectively, indicating these materials were shown to be mainly composed of amylopectin-like polymer.

• Journal of KSNVE
• /
• v.4 no.1
• /
• pp.43-50
• /
• 1994

Chatter vibration of a rolling machine in steel plants has a significant effect on thickness quality of the products. The cause and mechanism of the mill chattering is addressed through measurement of vibration and dynamic torque. An FFT system and an FM telemetry system are employed to collect data at several locations of possible damages. The results reveal the followings as sources of the mill vibration. The first is defects in roller bearings of a work roll chock. The second is instability of an oil film bearing in a backup roll chock, which has been investigated with a theoretical model describing the phenomenon. Dynamic torque is not the direct cause of mill vibration but rather influenced by the vibration. Appropriate treatment methods are suggested to address each of the above sources.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.241-245
• /
• 2004

Among the various manufacturing processes of composites, the tape lay-up process of thermoset prepreg has many advantages compared to autoclave or hot press forming. It has a high potential to process automation and continuous fabrication .. Fiber placement developed as a logical combination of filament winding and automated tape placement to overcome some of the limitations of each manufacturing method. Fiber placement uses a compaction device to apply direct contact between the incoming materials in the fiber placement head and Heat is added to the materials at the nip point of the compaction roller. This paper will discuss property of thermoset composite as compaction and heat effect in Automated fiber placement

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.4
• /
• pp.547-554
• /
• 2013

The fuel storage vessel installed in CNG vehicles can be largely divided into 3 parts: head, cylinder, and dome. Studies of the cylinder and dome parts have already been performed, but sufficient design data is not available about the head part. Therefore, expert field engineers heavily depend upon trial-and-error methods. Therefore, FE analysis is performed to review the hot spinning process for forming the head part of the CNG vessel using the Arbitrary Lagrangian-Eulerian (ALE) method. The effects of forming factors on the load were analyzed. The values of the factors were chosen to avoid defects in the head part and buckling, and the forming feasibility of the head part was investigated. Furthermore, a bursting test was performed to evaluate the safety of the storage vessel.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.6
• /
• pp.596-600
• /
• 2013

We report here on the processing and manufacturing of thin film for printed electronics by micro-gravure coating system. The micro-gravure coating systems are consisted of various modules such as web and system tension controller, micro-gravure coating units, dispenser and hybrid dry units (UV, NIR, Hot air). Especially, for the optimization of system, the number of idle roller was minimized and tension isolating infeeder was included. Also, we applied four patterns circle, 45 degree, square and 35 degree for the optimizing coating thickness. The micro-gravure coating system which applied various patterns to enable continuous coating process and fast coating time compare with conventional batch coating system. In this paper, introduce of micro-gravure coating system and testing results of coating thickness (20~700nm), coating time (1~2sec) and surface roughness (3~12nm) by using micro-gravure coating system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.10 s.241
• /
• pp.1315-1320
• /
• 2005

TiNi alloy fiber was used to recover the original shape of materials using its shape memory effect. The shape memory alloy plays an important role within the metal matrix composite. The shape memory alloy can control the crack propagation in metal matrix composite, and improve the tensile strength of the composite. In this study, TiNi/A16061 shape memory alloy(SMA) composite was fabricated by hot press method, and pressed by a roller for its strength improvement. The four kinds of specimens were fabricated with $0\%,\;3.2\%,\;5.2\%\;and\;7\%$ and volume fraction of TiNi alloy fiber, respectively. A fatigue test has performed to evaluate the crack initiation and propagation for the TiNi/A16061 SMA composite fabricated by かis method. In order to study the shape memory effect of the TiNi alloy fiber, the test has also done under both conditions of the room temperature and high temperature. The relationship between the crack growth rate and the stress intensity factor was clarified for the composite, and the cold rolling effect was also studied.

• Korean Journal of Materials Research
• /
• v.8 no.5
• /
• pp.436-443
• /
• 1998

2.3%C-26%Cr-1%Ni-0.5%Mo 조성의 다합금계 고크롬백주철을 고주파유도용해로를 사용하여 주조한 후 응고조직, 열처리조직 및 기계적성질간의 상관관계를 연구하였다. 주방상태에서는 초정덴드라이트조직인 기지조직과 공정탄화물로 구성되어 있었으며 기지조직의 73%가 오스테나이트, 27%가 마르텐사이트조직이었다. $900^{\circ}C$에서 5시간동안 균질화열처리만 행한 시편의 경우, 기지조직은 거의 페라이트로 구성되어 있었으며 $1100^{\circ}C$에서 불안정화열처리후 강제공냉시킨 시편의 경우, 유지시간에 따라 기지조직내의 잔류오스테나이트함량은 48.9-57.6%의 범위에 놓여 있었다. 주방상태 및 열처리시편 공히 마모량과 마모시간과의 관계가 직선적으로 얻어 졌는바 마모속도는 $2.77x10^{-2}$ /$~4.12x10^{-2mg}$ /sec의 범위에 걸쳐 있었다. 주방상태의 시편이 내마모성이 가장 우수하였으며 균질화열처리만 행한 시편이 가장 열악하였다. 기지조직내 잔류오스테나이트함량의 비율이 높아짐에 따라 경도는 감소하였고 반면에 내마모성은 향상되었다. 이는 마찰마모시험시 접촉부위의 오스테나이트가 가공경화를 일으켜 마르텐사이트로 변태되었기 때문으로 사려된다.