• Imaging Science in Dentistry
• /
• 제31권2호
• /
• pp.85-91
• /
• 2001

Purpose: To evaluate the effect of the slice thickness and the size of region of interest (ROI) on CT number using quantitative CT phantom Materials and Methods: The phantom containing 150 mg/cc, 75 mg/cc and 0 mg/cc calcium hydroxyapatite was scanned with 1, 3, 5 and 10 mm slice thicknesses by single energy quantitative computed tomography (QCT). CT numbers were measured on center position of the phantom. Shape of ROI was circular and sizes were 1, 3, 5, 11, 16, 21, 26 and 33 mm². ANOVA and Tukey's multiple comparison method were performed for statistical comparison of CT numbers according to different slice thicknesses. Coefficient of variation of CT number measured in each size of ROI was evaluated in same slice thickness. Results : CT numbers had statistically significant difference according to slice thicknesses (p<0.05). As the slice thickness increased, CT number also increased. As the density of phantom became lower and the size of ROI became smaller, the coefficient of variation of CT number increased. When the size of ROI was more than 11 mm² in 1 mm slice thickness, 5 mm² in 3 mm slice thickness and 3 mm² in 5 mm slice thickness, the coefficient of variation became consistent. In 10 mm slice thickness, the size of ROI had little effect on the coefficient of variation. Conclusion: CT number had variation according to the slice thickness and the size of ROI although the object was homogeneous. The slice thickness and the size of ROI are critical factors in precision of the CT number measurements.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권2호
• /
• pp.104-108
• /
• 1999

The electrical conductive mechanism and temperature dependence of electrical resistivity of $\alpha-SiC-ZrB_2$ composites with $ZrB_2$ contents were investigated. The electrical resistivity of hot-pressed composites was measured by the Pauw method form $25^{\circ} to 700^{\circ}C$. The electrical resistivity of the composites follow the electrical conduction model for a homogeneous mixture of two kind of particles with different conductivity. Also, the electrical resistivity versus temperature curves indicate the formation of local chains of $ZrB_2$ particles. In case of $\alpha-SiC-ZrB_2$ composites containing above 39vol.% $ZrB_2$ showed positive temperature coefficient resistance(PTCR), whereas the electrical resistivity of $\alpha-SiC-21vol.% ZrB_2$ showed negative temperature coefficient resistance(NTCR).

• 한국콘텐츠학회논문지
• /
• 제10권5호
• /
• pp.210-219
• /
• 2010

본 연구에서는 선택모형을 이용하여 소비자패널자료를 분석함에 있어 시간의 흐름에 따라 동적(dynamic)으로 변화하는 소비자내부의 특성 차이를 반영한 특정소비자의 종적인 변화인 소비자동태성을 분석하였다. 선택모형 내에서 소비자동태성은 효용함수에 시변계수(time-varying coefficient)를 도입함으로써 표현될 수 있다. 본 연구에서는 이를 위해 계층적모형(hierarchical model)과 상태공간모형(state-space model)에 기반하여 Random-Walk 계수를 지니는 이산프로빗모형을 개발하였고, 개발된 모형을 패널자료로부터 추정하기 위하여 Gibbs 표본법을 적용하였다. 모형추정결과 효용함수의 시변계수들에 유의한 소비자동태성이 존재함을 확인할 수 있었다. 소비자동태성이 존재할 경우 이에 효과적으로 대응하기 위해서는 동적시장세분화가 필요하다고 할 수 있다.

• 대한원격탐사학회지
• /
• 제31권4호
• /
• pp.337-346
• /
• 2015

Water body extraction based on backscatter information is an essential process to analyze floodaffected areas from Synthetic Aperture Radar (SAR) image. Water body in SAR image tends to have low backscatter values due to homogeneous surface of water, while non-water body has higher backscatter values than water body. Non-water body, however, may also have low backscatter values in high resolution SAR image such as Kompsat-5 image, depending on surface characteristic of the ground. The objective of this paper is to present a method to increase backscatter contrast between water body and non-water body and also to remove efficiently misclassified pixels beyond true water body area. We create an entropy image using a Gray Level Co-occurrence Matrix (GLCM) and classify the entropy image into water body and non-water body pixels by thresholding of the entropy image. In order to reduce the effect of threshold value, we also propose Water Body Texture Index (WBTI), which measures simultaneously the occurrence of repeated water body pixel pair and the uniformity of water body in the binary entropy image. The proposed method produced high overall accuracy of 99.00% and Kappa coefficient of 90.38% in water body extraction using Kompsat-5 image. The accuracy analysis indicates that the proposed WBTI method is less affected by the choice of threshold value and successfully maintains high overall accuracy and Kappa coefficient in wide threshold range.

• 한국분말재료학회지
• /
• 제17권2호
• /
• pp.107-112
• /
• 2010

Carbon-nanotube-embedded bismuth telluride (CNT/$Bi_2Te_3$) matrix composites were fabricated by a powder metallurgy process. Composite powders, whereby 5 vol.% of functionalized CNTs were homogeneously mixed with $Bi_2Te_3$ alloying powders, were successfully synthesized by using high-energy ball milling process. The powders were consolidated into bulk CNT/$Bi_2Te_3$ composites by spark plasma sintering process at $350^{\circ}C$ for 10 min. The fabricated composites showed the uniform mixing and homogeneous dispersion of CNTs in the $Bi_2Te_3$ matrix. Seebeck coefficient of CNT/$Bi_2Te_3$ composites reveals that the composite has n-type semiconducting characteristics with values ranging $-55\;{\mu}V/K$ to $-95\;{\mu}V/K$ with increasing temperature. Furthermore, the significant reduction in thermal conductivity has been clearly observed in the composites. The results showed that CNT addition to thermoelectric materials could be useful method to obtain high thermoelectric performance.

• 오토저널
• /
• 제10권6호
• /
• pp.72-84
• /
• 1988

Engine performance is one of the main objectives specified at the beginning of a new engine design project. The cycle simulation for SI engine is based on the zero-dimensional gas exchange model and a heat release expression by Viebe. This program also requires minimum input data and takes only a short time to run. Heat transfer from cylinder transfer formula. The flow coefficient (effective area) is calculated from valve lift using the standard flow coefficient curve and engine friction is calculated from the Millington and Hartles' engine friction formula. The chemical species considered in burned gas are 6 species CO, CO, H$_{2}$, H$_{2}$O, $O_{2}$, N$_{2}$ and the cylinder pressure, homogeneous cylinder temperature, gas composition and burned fraction are calculated at each crank angle through the cycle. To check the validity and accuracy, experimental study was done with 3 engines for measuring cylinder pressure, indicated mean effective pressure, brake mean effective pressure and air flow rate, etc. Despite its simple assumptions, cycle simulation showes excellent breathing and performance correlation when compared with data of tested engines, and have been proved useful in engine design.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.493-496
• /
• 2009

Phase stabilized leucite, which has high coefficient of thermal expansion, was synthesized, and its thermal expansion behavior was investigated. The homogeneous leucite phase was synthesized by solid state reaction from the mixture of $K_2CO_3-Al_2O_3-SiO_2$. and its stabilization from tetragonal to cubic phase was attempted by adding $Cs_2CO_3$ into starting materials. And fine powder with an average particle size of a few hundreds ${\mu}m$ were fabricated by planetary milling. During milling, amorphization of leucite was observed and recrystallized after heat treatment. The thermal expansion behavior of tetragonal and cubic leucite has measured and discussed. The average coefficient of thermal expansion of tetragonal and cubic phase leucite from room temperature to $750^{\circ}C$ was $21.4{\times}10^{-6}/^{\circ}C$ and $14.5{\times}10^{-6}/^{\circ}C$, respectively.

• Journal of Information Technology Applications and Management
• /
• 제28권4호
• /
• pp.13-20
• /
• 2021

In this paper, I was applied the life distribution following linear failure rate distribution, Lindley distribution and Burr-Hatke exponential distribution extensively used in the arena of software reliability and were associated the reliability possessions of the software using the nonhomogeneous Poisson process with finite failure. Furthermore, the average value functions of the life distribution are non-increasing form. Case of the linear failure rate distribution (exponential distribution) than other models, the smaller the estimated value estimation error in comparison with the true value. In terms of accuracy, since Burr-Hatke exponential distribution and exponential distribution model in the linear failure rate distribution have small mean square error values, Burr-Hatke exponential distribution and exponential distribution models were stared as the well-organized model. Also, the linear failure rate distribution (exponential distribution) and Burr-Hatke exponential distribution model, which can be viewed as an effectual model in terms of goodness-of-fit because the larger assessed value of the coefficient of determination than other models. Through this study, software workers can use the design of mean square error, mean value function as a elementary recommendation for discovering software failures.

• Nuclear Engineering and Technology
• /
• 제53권8호
• /
• pp.2454-2463
• /
• 2021

The objective of this research is to the use of americium (AmO₂) as a burnable absorber effectively instead of conventional gadolinium (Gd₂O₃) for VVER-1200 reactor by analyzing its impacts on reactivity, power peaking factor (PPF), safety factor, and quality of the spent fuel. The assembly is burned to 60 GWd/t by using SRAC-2006 code and JENDL-4.0 data library for finding the optimum amount and effective way of using AmO₂ as a burnable absorber. From these studies, it is found that AmO₂ can decrease the excess reactivity like Gd₂O₃ without changing the criticality life span and enrichment of ²³⁵U. A homogeneous mixture of the 0.20% AmO₂+ 4.95% enriched UO₂ fuel rod (model MF-4) decreases the PPF than the reference assembly. The use of AmO₂+UO₂ in the integral burnable absorber (IBA) rod or the outer layer could also decrease the PPF up to 10 GWd/t but increases rapidly after 30 GWd/t, which could be a safety threat. The fuel temperature coefficient and void coefficient of the model MF-4 are the same as the reference assembly. In addition, 22% of initially loaded Am are burning effectively and contributing to the power production.

• 디지털산업정보학회논문지
• /
• 제10권4호
• /
• pp.19-27
• /
• 2014

Software reliability in the software development process is an important issue. Software process improvement helps in finishing with reliable software product. Infinite failure NHPP software reliability models presented in the literature exhibit either constant, monotonic increasing or monotonic decreasing failure occurrence rates per fault. In this paper, proposes the reliability model with log type mean value function (Musa-Okumoto and log power model), which made out efficiency application for software reliability. Algorithm to estimate the parameters used to maximum likelihood estimator and bisection method, model selection based on mean square error (MSE) and coefficient of determination($R^2$), for the sake of efficient model, was employed. Analysis of failure using real data set for the sake of proposing log type mean value function was employed. This analysis of failure data compared with log type mean value function. In order to insurance for the reliability of data, Laplace trend test was employed. In this study, the log type model is also efficient in terms of reliability because it (the coefficient of determination is 70% or more) in the field of the conventional model can be used as an alternative could be confirmed. From this paper, software developers have to consider the growth model by prior knowledge of the software to identify failure modes which can be able to help.