• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 춘계학술대회 논문집
• /
• pp.712-717
• /
• 2005

When the weight if a concrete member makes problems, or when the cost of the concrete is relatively high, it may be economical to use a hollow concrete member. But a hollow R.C column may have poor ductility because of the brittle failure at the inner face of the hollow R.C column. This brittle failure results from the absence of the confinement at the inner face of the hollow R.C column. To avoid this brittle failure an internally confined hollow R.C column by a steel tube was developed before. In this study, a hollow R.C column is internally confined by a corrugated steel tube instead of a general flat steel tube. And a column ductility is performed. Test results show that the energy ductility ratio of a internally confined hollow R.C column by a by a corrugated steel tube corresponds to $80\%$ of the energy ductility ratio of a general solid R.C column.

• Steel and Composite Structures
• /
• 제19권3호
• /
• pp.585-599
• /
• 2015

This paper presents the experimental work on fatigue life and specific fatigue strength of circular hollow sectioned steel tube and wood filled circular hollow section steel tube. Burning effect was observed in the case of circular hollow sectioned steel tube when it is subjected to Maximum bending moment of 19613.30 N-mm at 4200 rpm, but this did not happen in the case of wood filled hollow section. Statistical analysis was done based on the experimental data and relations have been built to predict the number of cycles for the applied stress or vice versa. The relations built in this paper can safely be applied for design of the fatigue life or fatigue strength of circular hollow sections and wood filled hollow sections. Results were validated by static specific bending strengths determined by ANSYS using a known applied load.

• 소성∙가공
• /
• 제7권5호
• /
• pp.496-504
• /
• 1998

The eccentric extrusion and bending process for the forming of the curved rectangular hollow tube is newly developed. Generally the bending process of hollow tube is the secondary process followed by the extrusion process of the hollow tube from the round billet. So many defects such as wrinkling and the difference of wall thickness can be happened during the secondary bending process. In order to avoid the defects the new process named as "the eccentric extrusion and bending process" is suggested and applied to the U-bending of rectangular hollow tube. In this paper the kinematically admissible velocity field between the dies surface and the internal plug boundary surface s developed for the curving velocity. By the using of this curving velocity field the curvature of extruded products can be calculated with the parameters such as eccentricity dies length friction constant aspect ratio.

• 한국건축시공학회지
• /
• 제21권4호
• /
• pp.293-303
• /
• 2021

국내 PC공장은 PC 유공 슬래브를 생산하기 위해 자동화 설비를 도입하거나 매입물 삽입을 통해 중공 단면을 구현하지만 PC공장의 과다한 초기투자비용이 생산원가의 증가라는 주요 원인으로 작용하기에 다른 대안이 필요한 상황이다. 따라서 본 연구에서는 PC 유공 슬래브 부재 생산시 고무 튜브를 내부 속빈 공간을 형성하는 거푸집으로 사용함으로써 다양한 중공 형상의 성형 및 대단면화, 초경량화, 신속생산 대응 가능을 통한 생산성 확보에 기여하고자 한다.

• 한국가스학회지
• /
• 제20권3호
• /
• pp.73-77
• /
• 2016

본 연구에서는 여러 가지의 절단면 형상을 구비한 중공축이 동등한 최적을 갖는 경우에 대한 변위거동 안전성을 유한요소법으로 해석하였다. FEM 해석결과에 의하면, 외측튜브, 중간튜브, 내측튜브와 이들 튜브 사이를 연결하기 위해 X-타입 또는 Y-타입의 칼럼을 설치하였을 때 중공축 길이의 중간부에서 발생하는 최대 변위량을 줄여주는 것으로 나타났다. 특히, 하중을 지지하기 위해 구비된 X-타입 또는 Y-타입의 칼럼을 위상차 없이 외측튜브와 내측튜브를 중심축을 향해 직접 연결하면 중공축의 변위량을 줄이는 효과가 있는 것으로 나타났다. 그리고 동등한 체적을 갖는 중공축에서 발생하는 수직 변위량을 줄여주고, 변위거동 안전성을 높이기 위해서는 하중을 지지하기 위한 칼럼의 두께를 두껍게 설계하는 것이 바람직함을 알 수 있다.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2007년도 정기총회 및 학술발표대회
• /
• pp.144-147
• /
• 2007

Internally Confined Hollow-Concrete Filled Tube(ICH-CFT) column which has two tubes on both side of concrete, inner tube and outer tube perform great seismic abilities, ductility and absorption of energy, by the tubes and the hollow part. So this study does qualitative analysis about seismic capacities depending on parameters - diameter of column, hollow ratio, thickness of tubes - by moment-curvature analysis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.874-877
• /
• 2002

The optogalvanic signals were measured using hollow cathode discharge tube with argon as buffer gas at change of discharge currents. A change of ionization rate due to electron collision causes an increase or decrease of the electric conductivity. This change in electric conductivity generates the optogalvanic signal. We conclude that optogalvanic signal has close relation with the lowest metastable atoms density at low current.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2007년도 정기 학술대회 논문집
• /
• pp.683-687
• /
• 2007

Internally Confined Hollow-Concrete Filled Tube(ICH-CFT) column which has two tubes on both side of concrete, inner tube and outer tube perform great seismic abilities, ductility and absorption of energy, by the tubes and the hollow pmt. So this study does qualitative analysis about seismic capacities depending on parameters diameter of column, hollow ratio, thickness of tubes - by moment-curvature analysis.

• 소성∙가공
• /
• 제22권1호
• /
• pp.17-22
• /
• 2013

Tube hydroforming is a technology that utilizes hydraulic pressure to form a tube into desired shapes inside die cavities. Due to its advantages, such as weight reduction, increased strength, improved quality, and reduced tooling cost, single-layered tube hydroforming is widely used in industry. However in some special applications, it is necessary to produce multi-layered tubular components which have corrosion resistance, thermal resistance, conductivity, and abrasion resistance. In this study, a hollow forming process to fabricate a part from multi-layered tubes for structural purposes is proposed. To accomplish a successful hydroforming process, an analytical model that predicts optimal load path for various parameters such as tube material properties, thickness of tubes, diameter of holes and the number of holes was developed. Tubular hydroforming experiments to fabricate a hollow part were performed and the optimal loading path developed by the analytical model was successfully verified. The results show that the proposed hydroforming process can effectively produce hollow parts with multi-layered tube without defects such as wrinkling or fracture.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.493-494
• /
• 2008

During the last years hollow core insulators started their success story in the field of high voltage engineering for electrical apparatus, substituting porcelain insulators. The termination, also named top and bottom fittings are used for the connection to the rest of the electrical apparatus. The top and bottom flange are attached to the composite to transmit mechanical load and also ensure the gas tightness. They are bonded by epoxy glue with a glass transition temperature of about $130^{\circ}C$-$150^{\circ}C$ the glass reinforced epoxy tube of filament winding. This paper describes the results of a study on the bonded joints of fiber reinforced epoxy tube and cast aluminum. This suggests that surface roughness and glue types play an important role in evaluating of gas sealing capability on the flange and fiber reinforced epoxy tube in the composite hollow bushing.