• 한국세라믹학회지
• /
• 제35권11호
• /
• pp.1171-1181
• /
• 1998

$SrZr_{0.95}$$Y_{0.05}$$O_{2.975}$ powder was synthesized by ultrasonic spray pyrolysis using a solution that Sr carbonate and Zr and Y nitrates were dissolved in a citric acid solution. The processes of particle formation were in-vestigated with respect to solution properties and pyrolysis temperature. With changing the solution con-centration form 0.1M to 0.01M there was a tendency that average sizes of droplets and particles were de-creased and their size distributions were narrowed. Citrate functional groups converted the droplets into gel particles which prevented an inhomogeneous precipitation of the metal ions and facilitated the diffusion of gases during thermal decomposition. As a result the powder having spherical particles without hollow par-ticles could be prepared. Low pyrolysis temperature led to amorphous particles due to incomplete pyrolysis and made the particles difficult to maintain spherical shape due to retarded gelation of the droplets. Whereas higher pyrolysis temperature produced hollow and broken particles because the droplets un-derwent rapid gelationand decomposition. The particles obtained at two pyrolysis temperature $500^{\circ}$and $1000^{\circ}C$ consisted of a perovskite phase and a very small amount of $SrCO_3$ However after calcination at $1000^{\circ}C$ the particles contained a single perovskite phase having an average particle size of 0.63${\mu}{\textrm}{m}$ and an apparent density near to the theoretical density.

• International Journal of Automotive Technology
• /
• 제2권4호
• /
• pp.165-170
• /
• 2001

This study is focussed on the investigation of spray characteristics from the high pressure gasoline injector for the application of gasoline direct injection engine. For the analysis of spray structure of high pressure gasoline injector; the laser scattering method with a Nd-Yag laser and the Phase Doppler particle analyzer system were applied to observe the spray development and the measurement of the droplet size and velocity of the spray, respectively. Also spatial velocity distribution of the spray droplet was measured by use of the particle image velocity system. Experimental results show that high pressure gasoline injector shapes the hollow-cone spray, and produce the upward ring shaped vortex on the spray surface region. This upward ring shaped vortex promotes the secondary atomization of fuel droplets and contributes to a uniform distribution of fuel droplets. Most of fuel droplets are distributed under 31$\mu m$ of the mean droplet size (SMD) and the frequency distribution of the droplet size under 25$\mu m$ is over 95% at 7 MPa of injection pressure. According to the experimental results of PIV system, the flow patterns of the droplets velocity distribution in spray region are in good agreement with the spray macroscopic behaviors obtained from the visualization investigation.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.1383-1390
• /
• 2009

This study conducted a series of drained triaxial test in order to determine the critical state parameters of a high compressible Jeju sand. Jeju sand is classified into mixed sand containing both siliceous and calcareous materials and has high extreme void ratios due to the angularity of grains and the intra-particle voids of hollow particles. It is observed that the behavior of Jeju sand is similar to that of general calcareous sand. The friction angle of Jeju sand at critical state gradually decreases with increasing the mean effective stress. Test result shows that the particle crushing resulted from stress during shear causes the reduction of void ratio at critical state.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 1999년도 춘계학술발표논문집
• /
• pp.1-6
• /
• 1999

A study was made to determine the effect of plastic pigment on the coating structure and printability of coated paper. Three basic plastic pigments were investigated such as solid-bead type of plastic pigment, binder type of plastic pigment and hollow type of plastic pigment. In the systems investigated, it was observed that particle shape and structure of plastic pigment had influenced on the rheology of coating color, the state of packing, and the properties of coated paper. The materials investigated were restricted to plastic pigments commonly uesd in paper coating formualtion. Inorganic pigments used in this research were kaolin clay which is platelets and calcium carbonate which is rhombic. Three kinds of plastic pigments were blended in the color made up with two inorganic pigments, respectively. The combination of pigments were carried out (1) to determined the effect of paticle structure of plastic pigment on the state of dispersion of coating color, (2) to observe the effect of temperature of calender on the property of coated paper prepared with plastic pigment. The data indicated that binder and hollow type of plastic pigment had the best results on improving the properties of coated paper such as paper gloss, opacity and air permeability ect. and solid-bead type of plastic pigment in the next place.

• Computers and Concrete
• /
• 제20권1호
• /
• pp.39-47
• /
• 2017

In this paper, mode I fracture toughness of rock was determined by direct and indirect methods using Particle Flow Code simulation. Direct methods are compaction tension (CT) test and hollow centre cracked quadratic sample (HCCQS). Indirect methods are notched Brazilian disk (NBD) specimen, the semi-circular bend (SCB) specimen, hollow centre cracked disc (HCCD), the single edge-notched round bar in bending (SENRBB) specimen and edge notched disk (END). It was determined that which one of indirect fracture toughness values is close to direct one. For this purpose, initially calibration of PFC was undertaken with respect to data obtained from Brazilian laboratory tests to ensure the conformity of the simulated numerical models response. Furthermore, the simulated models in five introduced indirect tests were cross checked with the results from direct tests. By using numerical testing, the failure process was visually observed. Discrete element simulations demonstrated that the macro fractures in models are caused by microscopic tensile breakages on large numbers of bonded discs. Mode I fracture toughness of rock in direct test was less than other tests results. Fracture toughness resulted from semi-circular bend specimen test was close to direct test results. Therefore semi-circular bend specimen can be a proper test for determination of Mode I fracture toughness of rock in absence of direct test.

• 상하수도학회지
• /
• 제19권1호
• /
• pp.47-52
• /
• 2005

This study was conducted to evaluate the performance of submerged hollow fiber MF processes to treat secondary wastewater for water reuse. Specifically, membrane productivity and filtrate water quality were investigated under various operating conditions (i.e. flux, recovery, and backwash rate) at pilot-scale. Membrane fouling became more severe with increasing flux and recovery, suggesting that low flux operation (< 25 LMH) was desirable. At high flux operating(> 37.5 LMH), increasing backwash rate showed only limited success. The biofouling, quantified by PEPA and BFHPC, was also significant in wastewater reclamation, and biogrowth control by chlorine, were necessary to improve membrane productivity. Filtrate water qualities are in good compliance with water reuse regulations regardless of operating conditions (flux, recovery and backwash rate). Particle (e.g. turbidity) removal ranged from 89 to 98%, while only 11 to 21% of organics (e.g. NPDOC) were removed by MF membrane. Only small improvement in biostability (e.g. AOC) was achieved by MF system, and thus, without post disinfection, significant microorganisms might be present in the filtrate due to regrowth. Lastly, in order to further investigate pathogen removal, controlled microbial challenge tests were performed by monitoring Giardia, Cryptosporidium, bacteria and virus, and showed relatively good microbial removal.

• 공업화학
• /
• 제10권8호
• /
• pp.1186-1191
• /
• 1999

고분자 화합물의 첨가제로서 개질제, 물성 향상제, 충진제, 강화제 등의 용도로 사용되고 있는 유리 중공구체를 혼합액상 전구체를 사용하여 제조하였다. 혼합액상 전구체는 40% 규산나트륨($Na_2O:SiO_2$= 1:2) 수용액에 불용제인 붕산과 팽창제인 요소를 혼합한 용액이며, 이 용액을 오븐에 건조시킨 후, 볼밀로 분쇄시켜 기체 화염로에 투입될 원료 입자를 제조하였다. 유리 중공구체의 물성에 영향을 미치는 인자로서는 로에 투입될 원료 입자의 크기($53{\sim}63{\mu}m$, $63{\sim}180{\mu}m$)와 로 내부의 온도($800{\sim}1200^{\circ}C$), 그리고 요소의 변화량(0~30 g)을 택하여 실험하였으며, 실험 결과 유리 중공구체의 평균 입경은 원료 입자의 크기가 작을수록, 로 내부의 온도가 클수록, 그리고 요소의 조성이 증가할수록 증가하는 결과를 보여 주었다. 또한, 유리 중공구체의 파쇄 강도는 요소의 양이 증가할수록 감소하는 경향을 나타내었다.

• Structural Engineering and Mechanics
• /
• 제85권3호
• /
• pp.337-351
• /
• 2023

In this paper, the shear behavior of soft filling in rectangular-hollow concrete specimens was simulated using the 2D particle flow code (PFC2D). The laboratory-measured properties were used to calibrate some PFC2D micro-properties for modeling the behavior of geo-materials. The dimensions of prepared and modeled samples were 100 mm×100 mm. Some disc type narrow bands were removed from the central part of the model and different lengths of bridge areas (i.e., the distance between internal tips of two joints) with lengths of 30 mm, 50 mm, and 70 mm were produced. Then, the middle of the rectangular hollow was filled with cement material. Three filling sizes with dimensions of 5 mm×5 mm, 10 mm×5 mm, and 15 mm×5 mm were provided for different modeled samples. The parallel bond model was used to calibrate and re-produce these modeled specimens. Therefore, totally, 9 different types of samples were designed for the shear tests in PFC2D. The shear load was gradually applied to the model under a constant loading condition of 3 MPa (σc/3). The loading was continued till shear failure occur in the modeled concrete specimens. It has been shown that both tensile and shear cracks may occur in the fillings. The shear cracks mainly initiated from the crack (joint) tips and coalesced with another one. The shear displacements and shear strengths were both increased as the filling dimensions increased (for the case of a bridge area with a particular fixed length).

• 멤브레인
• /
• 제32권2호
• /
• pp.150-162
• /
• 2022

수처리 및 의약바이오 분야에서 유효물질 분리에 활용되고 있는 알루미나 중공사 분리막은 얇은 두께로 인해 취급 및 적용시 쉽게 파괴되는 단점이 있기 때문에 분리막의 강도를 100 MPa 이상으로 향상시키기 위한 연구가 필요하다. 본 연구에서는 나노입자의 함량을 0, 1, 3, 5 wt%로 증가시켰을 때 제조된 중공사 분리막의 특성을 평가하였다. 그 결과, 나노입자의 함량이 증가함에 따라 중공사 분리막의 강도는 79 MPa에서 115 MPa로 증가하였으며, 밀도는 1.76 g/m³에서 1.88 g/m³으로 증가하였고 기공률과 평균기공크기는 각각 51%에서 48%로, 416 nm에서 352 nm로 감소한 것을 확인하였다. 스폰지구조가 발달하고 스폰지구조의 기공크기가 향상된 알루미나 중공사 분리막은 100 MPa 이상으로 기계적 강도가 향상되었으며, 약 100000 GPU의 높은 질소 투과도 및 약 3000 L/m²h의 높은 물 투과도를 나타내었다. 따라서, γ-알루미나 나노입자를 소결조제로 첨가하는 것은 α-알루미나 중공사 분리막의 기계적 강도를 효과적으로 증진시키고 높은 투과성능을 유지할 수 있는 매우 유효한 방법임을 확인하였다.

• 접착 및 계면
• /
• 제16권2호
• /
• pp.76-82
• /
• 2015

SPG 막유화법에 의해 NIPAAm, MBA 및 APS를 용해시킨 수용액을 톨루엔과 미네랄오일의 혼합용액인 연속상에 HMP, Span80과 함께 유화(W/O emulsion)시킨 후, UV광중합법에 의해 PNIPAAm 하이드로젤 입자를 제조하였다. 연속상 내 미네랄 오일의 비율이 증가할수록, PNIPAAm 하이드로젤의 입도와 입자 내 PNIPAAm의 밀도가 증가하였으며, 이에 따라서 VPTT 근처에서 온도 변화에 따른 하이드로젤의 팽윤도($V/V_o$)도 크게 변화하였다. UV 광중합 시 $20^{\circ}C$에서는 속이 꽉찬 형태의 하이드로젤이 제조되었으나 LCST보다 높은 $40^{\circ}C$의 온도에서는 공동입자에서와 같이 하이드로젤의 외벽이 두껍게 형성되었다. 가교제인 MBA의 함량이 증가함에 따라서 가교도 및 입자 내 PNIPAAm의 밀도도 함께 증가하였다.