• Transactions of Materials Processing
• /
• v.26 no.5
• /
• pp.300-305
• /
• 2017

In this paper, a design method for an intermediate die was developed to manufacture a hollow linear motion guide rail in mandrel drawing process based on virtual die method and backward tracing scheme. FE simulations and mandrel drawing experiments using Mn55Cr carbon steel were performed to prove the effectiveness of the proposed design method. Results of FE simulations and experiments showed that the proposed design method could lead to drawn products with sound shape and the highest dimensional precision.

• Applied Chemistry for Engineering
• /
• v.18 no.5
• /
• pp.438-443
• /
• 2007

Titanium oxide films were deposited by the HCP (hollow cathode plasma) reactor at room temperature. With results of simulation about HCP reactor, the temperature profile is uniform on substrate regardless of the heat generation at cathode. The velocity profile on the surface of substrate is more uniform with increasing the gap between cathode and substrate, and surface roughness was decreased with increasing the gap between cathode and substrate. We could confirm that the composition of oxide increased with RF-power, and the ratio of O to Ti in the films was about 2 : 1 at RF-power of 240 watt and distance between cathode and substrate of 3 cm.

• Applied Chemistry for Engineering
• /
• v.21 no.3
• /
• pp.353-355
• /
• 2010

Poly(methyl methacrylate) (PMMA) particles were prepared by soap-free emulsion polymerization of MMA in the presence of a cationic initiator, 2,2'-azobis(2-methylpropionamidine) (AIBA). The Stober method has been adopted to coat silica on the surface of these cationic particles. Negatively charged silica precursors were coated onto cationic particle surfaces by electronic interaction. During the coating process, hollow particles were directly obtained by dissolution of PMMA.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.300-303
• /
• 2015

GaSe Single tetralayer의 $4{\times}4$ supercell을 사용하여 alkali metal (Li, Na)의 안정한 흡착 위치를 계산하였다. 가능한 흡착 위치로써 hollow, on top of Se, on top of Ga, Ga-Se bridge, Se-Se bridge를 조사하였다. 위치에 따른 흡착 에너지를 DFT 계산을 통해 얻었고, 계산 값을 통해 가장 안정한 위치를 선정하였다. 그 결과 하나의 원자가 흡착 될 때의 가장 안정한 위치는 hollow 위치이고, bridge 위치는 불안정하다는 것을 알 수 있었다. 또한 가장 안정한 hollow 위치에 두 개의 원자를 거리를 변화시키며 흡착 시켜 계산한 결과, 가장 가깝게 흡착 되었을 때 가장 안정했고 이때 tetralayer의 구조 변형이 두드러짐을 알 수 있었다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.05a
• /
• pp.101-102
• /
• 2016

Through the story height reducing method, cost saving can be implemented in many aspects. Recently, as one of PC floor system, HCS(Hollow Core Slab) has been applied in many project, and it is proved that it is excellent in productivity, economic efficiency, and workability as well. We developed a new composite beam(ANI Girder) which can be associated with HCS and reinforced with a truss-shape rebar and angle. As a result of actual application on underground parking building with HCS, it is confirmed that this system is effective in workability and story height reducing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.488-491
• /
• 2002

We report the observation of line shapes in the optogalvanic spectrum, which are different from those of absorption, for transitions origination from the $3P_2$ ($1s_5$ in Paschen notation) metastable level of argon. The OG line shapes resemble those of absorption and be used to diagnose the characteristics of the discharge plasma. The measured plasma temperatures of Ar hollow cathode discharge for several metal cathodes are about 620~780K at discharge current of 7~10mA.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.495-498
• /
• 2002

This paper describes the results the problem of stress calculation and optimization into a FRP(Fiber-glass Reinforced Plastic) tube crimped into a metal end-fitting. This type of assembly is used mainly is used mainly for suspension and line post insulators. Fitting strength of FRP and flange of this study is required greatly from composite insulator to important special quality. Therefore, wish to seek analysis and mechanical strength performance that follow to FRP tube and flange of top and bottom mechanical fitting.

• Structural Engineering and Mechanics
• /
• v.37 no.2
• /
• pp.177-196
• /
• 2011

An economic, structurally effective and practically applicable strengthening technique was developed for reinforced concrete (RC) framed buildings. The idea of the technique is to convert the existing hollow brick infill wall into a load carrying system acting as a cast-in-place RC infill wall by bonding relatively thin high strength precast concrete PC panels to the plastered hollow brick infill. For this purpose, a total of eight one-third scale, one bay, one story frames were tested under reversed-cyclic lateral loads. Test frames were designed and constructed with common deficiencies observed in practice. Four different panel types were used for strengthening. Test results showed that both strength and stiffness of the frames were significantly improved by the introduction of PC panels. Experimental results were compared with the analytical approaches suggested by the authors.

• Structural Engineering and Mechanics
• /
• v.43 no.2
• /
• pp.225-237
• /
• 2012

This paper presents an experimental investigation of the flexural behavior of square hollow steel section (HSS) beams subjected to pure bending. Totally six unfilled and nine ultra high performance concrete (UHPC)-filled HSS beams were tested under four-point bending until failure. The effects of the steel tube thickness, the yield strength of the steel tube and the strength of concrete on moment capacity, curvature, and ductility of UHPC-filled HSS beams were examined. The performance indices named relative ductility index (RDI) and strength increasing factor (SIF) were investigated with regard to different height-to-thickness ratio of the specimens. The flexural strengths obtained from the tests were compared with the values predicted by Eurocode 4, AISC-LRFD and CIDECT design codes. The results showed that the increase in the moment capacity and the corresponding curvature is much greater for thinner HSS beams than thicker ones. Eurocode 4 and AISC-LRFD predict the ultimate moment capacity of the all UHPC-filled HSS beams conservatively.

• Smart Structures and Systems
• /
• v.6 no.8
• /
• pp.975-989
• /
• 2010

Based on the theory of piezo-elasticity, the paper obtains the exact solutions of functionally graded piezoelectric hollow cylinders with different piezoelectric parameter $g_{31}$. Two kinds of piezoelectric hollow cylinders are considered herein. One is a multi-layered cylinder with different parameter $g_{31}$ in different layers; the other is a continuously graded cylinder with arbitrarily variable $g_{31}$. By using the Airy stress function method with plane strain assumptions, the exact solutions of the mechanic and electrical components of both cylinders are obtained when they are subjected to external voltage (actuator) and pressure (sensor), simultaneously. Furthermore, good agreement is achieved between the theoretical and numerical results, and useful conclusions are given.