• 소성∙가공
• /
• 제12권4호
• /
• pp.314-319
• /
• 2003

In the micro hole punching, the size and shape of burr and burnish zone are very important factors to evaluate quality of micro holes which depend on punch-die clearance, strain rate, workpiece material and etc. To get micro holes with small burr and wide burnish zone for industrial demands, not only the parametric study but also a study on fracture behavior in shear band are necessary. In this study, 100 $\mu$m, 25 $\mu$m micro holes in diameter were fabricated on brass (Cu63/Zn37) and SUS 316 foils as aspect ratio 1:1, and the characteristics of micro holes was investigated comparing with those of macro holes over several mm by scanning electron microscopic views and section views. Like macro hole, micro hole is also composed of 4 portions, rollover. burnish zone, fracture zone and burr, and it shows similar fracture behavior in shear band. But by high strain rate (10$^2$∼10$^3$s$^{-1}$ ) condition unlike that of macro hole fabrication and by the increment of relative grain size in the direction of the workpiece thickness, fracture zone is not observed.

• 대한기계학회논문집
• /
• 제19권5호
• /
• pp.1259-1268
• /
• 1995

The stress distribution around micro holes and the behavior of stress interaction between micro holes are considerd in the study. Several conclusions are extracted as follows : (1) The stress interaction varies with the distance e between micro holes. When the two micro holes are spaced in such a manner that theri two closest points are separated by a distance of micro hole radius (e=1), stress distribution is affected by a opposite micro hole in all the closest region. In addition, if two closest points are seperated by twice the distance of a micro hole radius (e=2), stress distribution is affected by a opposite micro hole in the region of -0.8.leq.x/r.leq.0.8 and the interaction effect can be neglected for e=4. (2)If the depth becomes larger than the radius, or the radius varies, the shape and magnitude of stress distribution around micro holes varies. (3) Hoop stress around a micro hole for the two dimensional configuration is larger than that of the three dimensional micro hole located on the surface of material for .theta. < 60.deg., but it is reversed for .theta > 60.deg.

• 대한기계학회논문집A
• /
• 제24권9호
• /
• pp.2167-2173
• /
• 2000

The HANARO (High-flux Advanced Neutron Application Reactor) has operated since 1995. The Cold Neutron(CN) hole was implanted in the reflector tank from the design stage. Before a vacuum chamber and a moderator cell for the cold neutron source are installed into the CN hole, it is necessary to measure the exact size of the inside diameter and thickness of the CN hole to prevent the interference problem. Due to inaccessibility and high radiation field in the CN hole, a mechanical measurement method is not permitted. The immersion ultrasonic technique is considered as the best method to measure the thickness and the diameter. The 4 axis manipulator of the 2 channel of a sensor module was fabricated. The transducer of 10 MHz results in 0.03 nun of resolution. The inside diameter and thickness for 550 points of the CN hole were measured using 2 channel ultrasonic sensors. The results showed that the thickness is in the range of 13-6.7 mm and inside diameter is in the range of o 156-165. These data will be a good reference in the design of a cold neutron source facility.

• Journal of Biosystems Engineering
• /
• 제27권6호
• /
• pp.557-564
• /
• 2002

Corrugated board is an efficient low-cost structure material fur the boxes that are widely used for transporting, storing and distributing goods. Corrugated board is also considered as an orthotropic because the principal material directions are the same as in paperboard. The purpose of this study was to elucidate the principal design parameters of ventilating box through the FEA on the various types of ventilating hole. From the viewpoint of the stress distribution and stress level, the optimum pattern and location of the ventilating hole were vertically oblong, and symmetry position with a short distance to the right and left from the center of front and rear panel. And, the optimum location and pattern of hand hole were a short distance to the top from the center of both side panels, and modified shape to increase the radius of curvature of both side in horizontal oblong. In general, the optimum pattern and location of both the ventilating hole and hand hole based on the FEM analysis were well verified by experimental investigation. It is suggested that decrease in compressive strength of the box could be minimized in the same ventilating hole area under the condition of the length of major axis of ventilating hole is less than 1/4 of box length, the ratio of minor axis/major axis is 113.5∼l/2.5, and number of the ventilating holes is even and symmetrical.

• 한국정밀공학회지
• /
• 제25권1호
• /
• pp.79-84
• /
• 2008

For the precision measurement of industrial products, the location of holes inside the products, if they exist, are often selected as feature points. The measurement of hole location would be performed by vision and laser-vision sensor. However, the usage of those sensors is limited in case of big change of light intensity and reflective shiny surface of the products. In order to overcome the difficulties, we have developed a hole displacement measuring device using contact-type displacement sensors (LVDTs). The developed measurement device attached to a robot measures small displacement of a hole by allowing its X-Y movement due to the contact forces between the hole and its own circular cone. The developed device consists of three plates which are connected in series for its own function. The first plate is used for the attachment to an industrial robot with ball-bush joints and springs. The second and third plates allow X-Y direction as LM guides. The bottom of the third plate is designed that various circular cones can be easily attached according to the shape of the hole. The developed system was implemented for its effectiveness that its measurement accuracy is less than 0.05mm.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.167.2-167.2
• /
• 2005

• 대한기계학회논문집A
• /
• 제40권4호
• /
• pp.337-342
• /
• 2016

스퍼드캔(spudcan)은 잭업리그(jack-up rig)의 다리 하단에 장착되며, 해저면에 구조물을 안정적으로 지지하여 구조물의 전복사고를 방지하기 위한 장치이다. 표층이 모래 층일 때는 침투(penetration) 시에 스퍼드캔을 안정적으로 삽입하기 위해서, 그리고 점토 층일 때는 회수(extraction) 시에 원활하게 뽑아 올리기 위해서 스퍼드캔에는 물 분사장치가 장착되어 있다. 본 연구에서는 물 분사장치를 위한 배관라인용 홀의 형상을 최적화하기 위해 크게 타원형과 원형 두 가지 형상을 설정하였다. 해석을 위해 대상 Site 는 멕시코만(Gulf of Mexico)로 선정하였고 대상 플랫폼은 해상풍력발전기설치선(WTIV)을 선택하였다. 상용프로그램인 ANSYS Workbench 를 사용하여 최적설계를 진행하였다. 본 연구결과는 다양한 해양구조물의 홀 형상설계에 적용될 수 있다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.992-995
• /
• 2003

A haptic device operated by the user's hand can receive information on position and orientation of the hand and display force and moment generated in the virtual environment to the hand. For realistic haptic display, the detailed information on collision between objects is necessary. In the past, the point-based graphic environment has been used in which the end effector of a haptic device was represented as a point and the interaction of this point with the virtual environment was investigated. In this paper, the shape-based graphic environment is proposed in which the interaction of the shape with the environment is considered to analyze collision or contact more accurately. To this end. the so-called Gilbert-Johnson-Keerthi (GJK) algorithm is adopted to compute collision points and collision instants between two shapes in the 3-D space. The 5- DOF haptic hand controller is used with the GJK algorithm to demonstrate a peg-in-hole operation in the virtual environment in conjunction with a haptic device. It is shown from various experiments that the shape-based representation with the GJK algorithm can provide more realistic haptic display for peg-in-hole operations.

• 한국안전학회지
• /
• 제21권1호
• /
• pp.92-95
• /
• 2006

This study is to find out how column with hole is behaved, compared to the normal one without hole. There might be existing buildings to make holes in the reinforced concrete column. Columns are made with commercially used compressive strength $240kg/cm^{2}$, air amount 5.0%, using re-bar of diameter D13 and D10 having yielding stress $4,000kg/cm^{2}$. The specimen were cured with temperature of $21{\pm}3^{\circ}C$. All specimens of five variables and all holes are geometrically considered and configurated. D3, D5 mean diameter 3cm and 5cm respectively. H1, H2 are the number of holes. Compressive pressure was forced in accordance with KS, following $0.6{\pm}0.4N/mm^{2}$ speed. Main re-bar's were strained with almost same shape through all the specimens. Hole diameter 5cm-having specimen showed cracking around hole. strains of back and front gauges of the specimen were showed similarly. Specimen having two holes in left and right from longitudinally axis resisted 7% less than the one having hole centrically from longitudinal axis. One hole having specimen with diameter 5cm resisted only 3% less than in case of 3cm diameter hole. Hole having in left and right from longitudinal axis will be less resistant than the case longitudinally arranged. Diameter 3cm hole showed less 10% capacity than normal one without hole. Capacity loss difference between diameter 3cm and 5cm showed almost none in case that they are arranged longitudinally.

• 복식
• /
• 제51권2호
• /
• pp.5-25
• /
• 2001

Jade, which is a kind of stone, with its transparent body, lustrous and bright character, But jade is not the only fair stone. There are three kinds of jade objects 1) tallies used in the court. 2) ceremonial jades. 3) ordinary jade for decoration, for inlaid work and for burial. Among the ceremonial jade, the most important were the "liu jui" and "liu ch′i." The former was supposed to be held by people in the court as symbols of their authority : 1) "then-kuei(鎭圭)" for the emperor. 2) "hang-kuei(恒圭)" for a duke, 3) "hsin-kuei(信圭)" a marquis. 4) "kung-kuei(躬圭)" for an earl, these "kuei" were alike in shape, but differed in size. 4) "ku-pi(穀璧)" for a viscount. 5) "p′u-pi(蒲璧)" for a baron, "pi(璧)" differed in decoration but were alike in shape. "Liu ch′i(六器)" were ceremonial objects used by the emperor in worshipping Heaven, Earth, and the Four Directions : "ts′ang-pi(倉璧)," greenish jade disk, used in worthipping Heaven "huang-tsung(黃琮)," yellow jade cylinder, used in worshipping Earth ; "cuing-kuei,(靑圭)" blue jade tablet. used in worshipping the East : "chih-chang(赤璋)," red jade tablet, used in worshipping the South : "hsuan-huang(玄璜)," black crescent, used in worshipping the North. Five kinds of tallies were "chen-kuei(鎭圭)," "yenkuei(琰圭)," "yuan-kuei(玩圭)," "ku-kuei(穀圭)." They were used to console people during disaster, to subjugate an official who had committed a crime, to reward a prize to an official for his merit or good conduct, to arbitrate disputes between high officials, to marry princess. and to dispatch troops. Since the west wei(西魏), Kuei and Hole were made of Ivory, wood and bamboo, who had ivory for fifth grade and wood and bamboo for under sixth grade. After Eastern Chou, all officials beginning to had kuei hole. symbol of Authority. and his wives. After Dang dynasty, Japan is the same. In korea. After king Bupheung in ancient and South(unification) Silla, North Kingdom Bohai, Koryo, and Chosen dynasty had ceremonial jade, Kuei and Hole.