• 전자공학회논문지A
• /
• 제31A권2호
• /
• pp.88-93
• /
• 1994

We fabricated a large-scale photovoltaic device for detecting-3-5$\mu$m IR, by forming of n$^{+}$-p junction in the $Hg_{1-x}Cd_{x}$Te (MCT) layer which was grown by LPE on CdTe substrate. The composition x of the MCT epitaxial layer was 0.295 and the hole concentration was 1.3${\times}10^{13}/cm^{4}$. The n$^{+}$-p junction was formed by B+ implantation at 100 keV with a does 3${\times}10^{11}/cm^{2}. The n$^{+}$ region has a circular shape with 2.68mm diameter. The vacuum-evaporated ZnS with resistivity of 2${\times}10^{4}{\Omega}$cm is used as an insulating layer over the epitaxial layer. ZnS plays the role of the anti-reflection coating transmitting more than 90% of 3~5$\mu$m IR. For ohmic contacts, gole was used for p-MCT and indium was used for n$^{+}$-MCT. The fabrication took 5 photolithographic masks and all the processing temperatures of the MCT wafer were below 90$^{\circ}C$. The R,A of the fabricated devices was 7500${\Omega}cm^{2}$. The carrier lifetime of the devices was estimated 2.5ns. The junction was linearly-graded and the concentration slope was measured to be 1.7${\times}10^{17}/{\mu}m$. the normalized detectivity in 3~5$\mu$m IR was 1${\times}10^{11}cmHz^{12}$/W, which is sufficient for real application.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.320-320
• /
• 2014

Amorphous silicon alloy (a-Si) solar cells and modules have been receiving a great deal of attention as a low-cost alternate energy source for large-scale terrestrial applications. Key to the achievement of high-efficiency solar cells using the multi-junction approach is the development of high quality, low band-gap materials which can capture the low-energy photons of the solar spectrum. Several cell designs have been reported in the past where grading or buffer layers have been incorporated at the junction interface to reduce carrier recombination near the junction. We have investigated profiling the composition of the a-SiGe alloy throughout the bulk of the intrinsic material so as to have a built-in electrical field in a substantial portion of the intrinsic material. As a result, the band gap mismatch between a-Si:H and $a-Si_{1-x}Ge_x:H$ creates a barrier for carrier transport. Previous reports have proposed a graded band gap structure in the absorber layer not only effectively increases the short wavelength absorption near the p/i interface, but also enhances the hole transport near the i-n interface. Here, we modulated the GeH4 flow rate to control the band gap to be graded from 1.75 eV (a-Si:H) to 1.55 eV ($a-Si_{1-x}Ge_x:H$). The band structure in the absorber layer thus became like a U-shape in which the lowest band gap was located in the middle of the i-layer. Incorporation of this structure in the middle and top cell of the triple-cell configuration is expected to increase the conversion efficiency further.

• Archives of Plastic Surgery
• /
• 제35권2호
• /
• pp.219-222
• /
• 2008

Purpose: The purpose of this study is to develop hydroxyapatite cement simplified procedures for reconstruction of craniofacial deformities. Due to its expense and characteristics of quick hardening time, it may be inappropriate for forehead reconstruction or augmentation. Therefore we hear by introduce a more precise, easy and cheap method. The authors report forehead reconstruction with hydroxyapatite cement for a patient who suffered from craniofacial deformity. Methods: Case report and literature review. Results: A 35 year old man came to us with forehead and temporal area depression. He had a history of brain operations due to traumatic epidural hematoma. A physical exam showed an evidence of right side forehead weakness sign. Authors made RP model of his skull and applied check framework with Kirschner's wires for measuring accurate volume and contour on the depressed right side forehead area on the RP model. After complete exposure of defect area by bicoronary insicion, absorbable plate which applied on skull area was removed. Using three Kirschner's wires, authors made check framework on the right forehead lively and fixed with 2-hole miniplates on the boundary of the defect. After checking asymmetry, hydroxyapatite was applied on check shape framework just above Kirschner's wire. After removing Kirschner's wire, we corrected minimal unbalance and contour with bur. Conclusion: Check framework with Kirschner's wire was very convenient and cost saving methods for forehead reconstruction with hydroxyapatite cement.

• 한국레이저가공학회지
• /
• 제14권2호
• /
• pp.8-12
• /
• 2011

As the aged population grows around the world, many medical instruments and devices have been developed recently. Among the devices, a drug delivery stent is a medical device which requires precision machining. Conventional drug delivery stent has problems of residual polymer and decoating because the drug is coated on the surface of stent with the polymer. If the drug is impregnated in micro hole array on the surface of the stent, the problem can be solved. Micro sized holes are generally fabricated by laser machining; however, the fabricated holes do not have an enough aspect ratio to contain the drug or a good surface finish to deliver it to blood vessel tissue. To overcome these problems, we propose a vibration-assisted machining mechanism with PZT (Piezoelectric Transducers) for the fabrication of micro sized holes. If the mechanism vibrates the eyepiece of the laser machining head, the laser spot on the workpiece will vibrate vertically because objective lens in the eyepiece shakes by the mechanism's vibration. According to the former researches, the vibrating frequency over 20kHz and amplitude over 500nm are preferable. The vibration mechanism has cylindrical guide, hollowed PZT and supports. In the cylinder, the eyepiece is mounted. The cylindrical guide has upper and low plates and side wall. The shape of plates and side wall are designed to have high resonating frequency and large amplitude of motion. The PZT also is selected to have high actuating force and high speed of motion. The support has symmetrical and rigid characteristics.

• 한국식생활문화학회지
• /
• 제29권5호
• /
• pp.428-436
• /
• 2014

This study was conducted to investigate the use of sugar alcohols (sorbitol, erythritol, and xylitol) as alternative sweeteners for replacing sucrose in Yukwa (traditional Korean oil-puffed rice snack). The moisture contents of Bandegi (dried Yukwa dough) and Yukwa containing sugar alcohols were higher than that of control (containing only sucrose). The microstructures of control and Bandegi containing sugar alcohols showed uniformly and finely distributed air holes. Expansion ratio and oil absorption of Yukwa containing sorbitol and 30% erythritol were higher than those of control. Appearance and cross section of control and Yukwa containing sorbitol, 30% erythritol, and 30% xylitol showed a good shape. The lightness (L) of control was significantly lower than Yukwa containing sugar alcohols, whereas redness (a) and yellowness (b) were higher than those in Yukwa containing sugar alcohols. Hardness of Yukwa containing sugar alcohols was significantly lower than that of control, and that of Yukwa containing sorbitol was the lowest. Peak number of Yukwa containing sugar alcohols was significantly lower than that of control, and that of Yukwa containing 60% erythritol and 60% xylitol was the lowest among all samples. In the sensory evaluation, color of control was deepest, whereas that of Yukwa containing 60% xylitol was lightest. Volume and air hole uniformity of Yukwa containing 60% erythritol and 60% xylitol were inferior than those of other samples. Sweetness of Yukwa containing sugar alcohols was lower than that of control, whereas oily flavor was stronger. Hardness of Yukwa containing sugar alcohols was lower than that of control, and Yukwa containing xylitol showed the lowest hardness among the samples. Crispness of Yukwa containing sugar alcohols was lower than that of control. There were no significant differences in overall acceptability between control and Yukwa containing 30% sorbitol and 30% erythritol. Overall, sorbitol and erythritol were appropriate as a 30% replacement for sucrose when preparing Yukwa.

• 혜화의학회지
• /
• 제15권2호
• /
• pp.75-93
• /
• 2006

Chang San-roe re-explained the contents from the 30th question to the 47th question of "Nan Jing" which refered to the Chang-Pu and physiological theories as follows through the western theory which wss different from the tranditioonal chinese theory 1. "Nan Jing" refered to the circulation and the coming into being of Yeong-Wi. He denied that it was classified Yeong from Wi or Eum from Yang. 2. He denied that Sam-Cho was separated to three parts and the theory of "Sam-Cho is name only, not shape", using western medical theory. 3. He denied the view about "Left side is kidney, right side is Myung-Mun" because it was incorrect that kidney was separated to two parts which were Su and Hwa or Eum and Yang 4. Re-explaining the contents of "Nan Jing"- the portions of heart and lungs, the rising and falling of liver and lungs, the relationships of five viscera and sound color smell taste fluid, the relationships of five viscera and nine hole, the relationships of five viscera and O-Chu, the physiological difference of the old and the young owing to the deflection of Yeong-Wi Chi-Heol- he thought that viewing the human body using theory of Eum and Yang, Five elements(五行) was a far-fetched interpretation, so he denied the tranditional chinese theory which understood human body's organs, physiology, pathology. 5. He explained the contents of "Nan Jing"- the portions of the colon and the small intestines, the funtion of the six bowls, the corespondence of Chang-Pu, physical peculiarity of liver, the anatomical aspects which were the sizes, weights, volumes and shapes of the Chang-Pu and the alimentary canal, Chil-Chung-Mun, Pal-Hoe-Hyeolthrough western anatomy and physiology in detail.

• 한국정밀공학회지
• /
• 제31권6호
• /
• pp.513-519
• /
• 2014

For depth machining in die and mold, Electrical Discharge Machining (EDM) is used generally. To make deep hole and deep shape efficiently, cemented carbide endmill for depth machining is necessary. For this purpose, cemented carbide endmill was designed using design of experiment (DOE). To improve cutting performance, endmill was coated with multilayer surface treatment, TiAlCrSiN and TiAlCrN, for higher wear resistance. In order to evaluate the endmill, Transverse Rupture Strength (TRS) test was tried for investigating the relationship between surface treatment and strength in endmill body. Scratch test was also used for measuring adhesion force of each surface treatment. To evaluate hardness of surface treatment, Atomic Force Microscope (AFM) analysis was carried out. Wear test was executed for characteristics of each surface treatment in high temperature. Consequently, TiAlCrSiN was superior to the TiAlCrN coating in case of high temperature environment such as cutting.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.1680-1686
• /
• 2009

삼각 분리 막대형 차압 유량계 압력 탭의 가공 조건에 따른 유량 특성을 연구하였다. 삼각 분리 막대탭 차압 유량계에 가공한 압력 탭의 크기는 1.0 mm 또는 1.5 mm로 하였다. 압력 탭의 개수는 5개 또는 17개로 가공하였다. 삼각 분리 막대탭 차압 유량계와 층류유량계를 직결한 후 유량 특성을 검정하였다. 삼각 분리 막대탭 차압 유량계의 질량 유량을 무차원 파라미터 H를 사용하여 나타내었다. H는 TSB 유량계에서의 배압, 기체 온도, 유량계 상류압과 하류압 간의 차압을 포함하는 무차원 파라미터이다. TSB 유량계의 질량 유량과 H 간에는 선형적 관계를 보였다. 압력 탭의 개수 보다는 압력 탭의 직경이 TSB 차압유량계의 유량 특성에 더 큰 영향을 미쳤다.

• 한국융합학회논문지
• /
• 제8권7호
• /
• pp.123-129
• /
• 2017

본 연구는 모발 수질의 형태적, 미세구조적 특성을 주사전자현미경과 투과전자현미경을 사용하여 관찰하였다. 수질은 모발의 중앙부위에 존재하며 모발의 장축을 따라 기부에서부터 정단부위까지 불연속적으로 존재한다. 또한, 수질은 일정한 모양으로 존재하지 않고 매우 불규칙한 모양을 하고 있다. 한 개의 모발에서 연속되는 수질의 두께는 매우 다양하게 나타났다. 모발의 가로 절단면에서 수질의 두께는 최고 $21{\mu}m$로 측정되었고 세로 절단면에서는 최고 $27{\mu}m$로 측정되었다. 수질은 모발 직경의 1/3-1/4을 차지하고 있다. 수질은 각화된 수질형성세포의 거대원섬유들이 분리되면서 빈 공간을 형성하고 있다. 수질에 형성된 빈공간은 최고 $6.5{\mu}m$의 직경을 가지고 있으며 공기로 채워져 있다.

• 한국융합학회논문지
• /
• 제8권7호
• /
• pp.231-236
• /
• 2017

본 연구에서는 고분자재료인 CFRP(Carbon Fiber Reinforced Plastic)과 구조용 금속인 SM45C로 이루어진 이종 복합재료가 경량화 재료용으로 사용되고 있다. SM45C를 심재로 갖고 양면에 섬유 적층각도가 다른 단반향 CFRP를 접착시킨 샌드위치형 복합재료를 이용하여 CT(Compact Tension)시험을 기초로 한 유한요소 해석을 진행하였다. CT시험은 하중을 받는 재료내의 크랙으로 인한 파괴거동을 확인하기 위한 대표적인 방법이다. 이종 복합재료를 기계 구조물에 적용하기 위해서는 크랙 및 구멍에 대한 영향을 연구하여야 한다. 샌드위치형 복합재료의 CT시험에 의한 파괴거동을 시뮬레이션 해석으로 연구하였다. 본 연구 결과로서, [0/60/-60/0]의 적층각도를 가진 단방향 CFRP 샌드위치형태 복합재료가 우수한 강도를 갖으며 최대 등가응력은 약 182GPa정도가 나타났다. 또한 복합 재료 형상으로서의 디자인적 요소를 융합 기술에 접목함으로서 그 미적인 감각을 나타낼 수 있다.