• 한국안전학회지
• /
• 제22권1호
• /
• pp.19-23
• /
• 2007

The aim of this study was to determine residual stresses in thermal barrier coatings(TBCs) by isothermal heating. Specimens were heated at the range of $1000{\sim}1600^{\circ}C$. A finite element method was used to determine the residual stresses. Finite element coupled heat transfer and elastic-plastic thermal stress analysis using a general purpose commercial FEM software ABAQUS. I obtained the stresses were not affected below the temperature of $1400^{\circ}C$ but affected over that of temperature.

• 지질공학
• /
• 제34권2호
• /
• pp.217-228
• /
• 2024

피압대수층은 이를 통과하는 대심도 시추에서 암편 배출 불능, 지하수의 급격한 공내 유입, 이수 손실 등의 문제를 야기한다. 특히 자분 조건일 경우 과압 공극압이 발생하여 적절한 이수 밀도의 적용이 필수적이다. 이 논문에서는 이수창 분석을 이용하여 피압대수층을 통과하는 시추 중 적정이수밀도(SMD)의 결정방법을 제시하고 이를 사례에 적용하여 적용성을 검토하였다. 심도별 이수창의 하한인 최소이수밀도는 해당 심도의 등가이수밀도 공극압 구배 또는 이에 이송 마진을 더하여 산정되며, 피압대수층의 공극압 구배는 피압지하수위 또는 정두압의 측정으로 구할 수 있다. 시추공이 피압대수층에 도달하면 공극압 구배가 급격히 증가하고, 심도가 증가할 수 록 점차 감소한다. 킥 발생을 방지하기 위한 SMD는 굴진 중인 공저 심도와 그 상부 나공 구간의 최소이수밀도 중 최대값으로 결정할 수 있으며, 피압대수층 진입 이후 SMD는 피압대수층 최상부의 최소이수밀도로서 나공 구간 시추 중 이를 유지하여야 한다. 또한 적절한 케이싱의 설치는 SMD를 낮출 수 있어 고투수성 대수층에 대한 이수 침입 또는 이수 손실의 위험을 감소시킬 수 있다.

• 한국지반신소재학회논문집
• /
• 제11권4호
• /
• pp.45-53
• /
• 2012

지반굴착은 지반조사, 연약지반 개량, 선굴착 말뚝 시공 등 지반공학 분야에서 널리 사용되고 있다. 지반을 굴착하기 위해서는 오거의 상부에 설치된 구동모터를 회전시키는 전기에너지가 필요하게 된다. 본 논문에서는 지반굴착시 구동모터에 소요되는 전기에너지와 지반의 표준관입시험 N값의 상관관계를 분석하고자 하였다. 이를 위하여 지반굴착시 변화하는 전류값과 굴착깊이를 계측하기 위한 측정센서, 데이터 저장시스템, 굴착시스템 등의 실내실험 장치를 개발하였으며, 모형토조 실험을 수행하였다. 계측된 전류값과 굴착깊이는 표준관입시험 N값 추정에 이용되었으며 추정된 표준관입시험 N값은 실내실험으로부터 실측된 N값과 비교하였다. 비교결과 지반굴착에 소요되는 전기에너지를 이용하여 표준관입시험 N값을 추정할 수 있음을 확인하였다.

• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.279-289
• /
• 2000

Residual stress induced in U-bending and tube-to-tubesheet joint processes of PWR's row-1 heat exchanger tube was measured by X-ray method and Hole-Drilling Method(HDM). Compressive residual stresses(-) at the extrados surface were induced in U-bending, and its maximum value reached -319 MPa in axial direction at the position of $\psi$ = $0^{\circ}$. Tensile residual stresses(+) of $\sigma_{zz}$ = 45 MPa and $\sigma_{\theta\theta}$ = 25 MPa were introduced in the intrados surface at the position of $\psi$ = $0^{\circ}$. Maximum tensile residual stress of 170 MPa was measured at the flank side at the position of $\psi$ = $90^{\circ}$, i.e., at apex region. It was observed that higher stress gradient was generated at the irregular transition regions (ITR). The trend of residual stress induced by U bending process of the tubes was found to be related with the change of ovality. The residual stress induced by the explosive joint method was found to be lower than that by the mechanical roll method. The gradient of residual stress along the expanded tube was highest at the transition region (TR), and the residual stress in circumferential direction was found to be higher than the residual stress in axial direction.

• 한국정밀공학회지
• /
• 제31권1호
• /
• pp.75-81
• /
• 2014

Laser beam machining has been known as efficient for glass micromachining. It is usually used the ultra-short pulsed laser which is time-consuming and uneconomic process. In order to use economic and powerful long pulsed laser, indirect processing called laser-induced backside wet etching (LIBWE) is good alternative method. In this paper, micromachining of glass using Nd:YAG laser with nanosecond pulsed beam has been attempted. In order to improve shape accuracy, combined processing with magnetic stirrer has been widely used. Magnetic stirrer acts to circulate the solution and remove the bubble but it is not suitable for deep hole machining. To get better effect, ultrasonic vibration was applied for improving shape accuracy.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.651-658
• /
• 2004

In this study, we introduced the spiral pipe nailing system (refer as SPN system) with self drilling method, can apply to ground which is hard to keep shape of bore hole, and performed limit equilibrium analysis with simplilied trial wedge method while length ratio and bond ratio were altered to evaluate slope stability considered of tensile strength and bending stiffness. A newly soil nailing system named as the SPN system is respected to reduce displacement of nail and increase global slope stability. And effects of various factors related to the design of the SPN system, such as the type of drilling method and the bit, are examined throughout a series of the displacement-controlled field pull-out tests. 6 displacement-controlled field pull-out tests are performed in the present study and the volume of grouting arc also evaluated based on the measurements. In addition, short-term characteristics of pull-out deformations of the newly proposed SPN system are analyzed and compared with those of the general soil nailing system by carrying out the displacement-controlled field pull-out tests.

• 비파괴검사학회지
• /
• 제9권2호
• /
• pp.61-66
• /
• 1989

Welding residual stress was measured by ultrasonic birefringence technique. Acoustoelastic constant was taken by averaging the values in the literature. The initial birefringence from prefered orientation of grains was measured. The EMAT transducers were used to remove couplant effect. The results show that the distribution and magnitude of welding residual stress from ultrasonic measurement are in good agreements with those from semi destructive hole drilling measurement.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1994년도 특별강연 및 춘계학술발표 개요집
• /
• pp.157-160
• /
• 1994

Characteristics of laterally bonded tri-metal sheets (stainless steel/Invar/stainless steel) fabricated by laser beam welding are compared to those of samples by Imphy and Hitachi Co-operations. Residual stess of tri-metal is calculated by using of the hole-drilling stain gauge method. The aging effect of stainless steel strip on welding is also discussed. In addition to, a numerical approach for laser beam welding is tried. Finally, laser beam welding system of tri-metal can be designed on th basis of experimental and theoretical results.

• Corrosion Science and Technology
• /
• 제16권6호
• /
• pp.294-297
• /
• 2017

For the longer service life of steel pile, cathodic protection is selected sometimes at corrosive environment. The cathodic protection design improvement was investigated in this study. The current demand for cathodic protection was calculated from the potentiostatic current monitoring of the steel specimen in the deaerated soil samples. In this study, the current distribution was studied using the Boundary Element Method (BEM) and the Finite Element Method (FEM) numerical analysis methods. The optimum layout of the anode was developed and confirmed by numerical analysis. Under the conventional design of the anode, the length of the anode hole is same as the pile length. We found that, at the bottom end of the pile, the current density is too high. When the anode hole length was 80% of the pile length, the current consumption at the end was reduced. The construction cost of anode hole drilling was decreased about 20%, as compared to the conventional design. Furthermore, the life of the anode materials could be extended by reducing the current consumption at the end section. Using this approach, the construction cost was reduced significantly without any under-protection area on the steel piles.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.412-417
• /
• 2005

To ensure the safety of the tunnelling without the loss of economy, the tunnel seismic profiling(TSP) method for the prediction ahead of tunnel face, begins to be used routinely in these days. TSP method does not interfere the tunnelling works while the horizontal drilling does, and its prediction length is longer than that of the drilling. Yet the most frequently adopted technique of TSP in Korea is the multi-shot and 2 receiver array using in-hole receivers, even though this array requires as many as 26 drill-holes for receiver installation and ballasting, which results in 3-6 hours of suspension in excavation work. In this paper, multi-receiver and lesser shot array using side-wall attached 3 component geophones is to be described to prove the efficiency in terms of the survey time as well as the reliability of the method by comparison of the predicted weak points and the face mapping results. The predictions mostly agreed with the real fractures or joint developed zones which have been confirmed during the excavation. It also has been found that TSP method can be effectively applied to perform draining ground water ahead of tunnel face by imaging the geologic discontinuities.