• Journal of the Korean earth science society
• /
• v.30 no.4
• /
• pp.454-463
• /
• 2009

In this study, from January 2006 to February 2009, we observed 107 ice spikes formed in a natural state, and analyzed their environment. We developed an experimental device to reproduce ice spikes in laboratory and successfully made 531 ice spikes. We analyzed the process of the formation and the principle of how those ice spikes grow through videotaped data of the formation in the experiment. In the natural world, when the surface of water and the lower part of a vessel begin to freeze, a vent (breathing hole) develops at the surface where an ice is not frozen; this vent serves as the seed of an ice spike. It is assumed that the volume expansion of ice in the vessel which occurs when water freezes makes the supercooled water go upward through the vent and becomes an ice bar called an ice spike. In the laboratory, however, when distilled water is poured into an ice tray cube and kept in the experimental device for about one and a half hours at a temperature of -12- $-13^{\circ}C$, a thin layer of ice then begins to develop on the surface of the water, the vent is formed, and ice spikes form for about 10-30 minutes. These spikes stop growing when the end becomes clogged. Ice spikes can be described as falling into seven categories of shape, with the apex type topping the list followed by the slant type in the natural state and the vertical type predominating in the laboratory.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.1
• /
• pp.64-70
• /
• 2023

In this study, reliability tests of torsion control expansion anchors according to drill bit diameters were performed. The standard deviation and coefficient of variation of the anchor were reviewed through the tests for each variable, and the results were compared and evaluated with the standard test results. As a result of the reliability test of the M12 and M16 anchors with 1.04 times the drill bit diameter, they were within 20% of the ultimate tensile load permissible standard coefficient of variation. It was found that the pulling-out performance of the anchor installed in the large hole was sufficiently secured. However, it was found to be about 253% and 210% of the design strength, indicating that the pulling performance of the anchor installed in 1.04 times the drill bit diameter was sufficiently secured. As a result of the reliability test of the M12 and M16 anchors with 1.02 times the drill bit diameter, the value of the coefficient of variation of the ultimate tensile load limit was within 20%, which satisfies the test standard. It was shown to be about 136% and 168% of the design strength, indicating that the pulling-out performance of the anchor installed in 1.02 times the drill bit diameter is sufficiently secured.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.260-260
• /
• 1999

We compared c-axis tunneling characteristics of small stacked intrinsic Josephson junctions prepared on the surface of pristine, I-, and HgI$_2$-intercalated Bi$_2Sr_2CaCu_2O_{8+x}$ (Bi2212) single crystals. The R(T) curves are almost metallic in I-Bi2212 specimens, but semiconducting in HgI$_2$-Bi2212 ones.· The transition temperatures were 82.0 K, 73.0 K, and 76.8 K for pristine Bi2212, I-Bi2212, and HgI2-Bi2212 specimens, respectively, consistent with p-T$_c$ phase diagram. Current-voltage (IV) characteristics of both kinds of specimens show multiple quasiparticle branches with well developed gap features, indicating Josephson coupling is established between neighboring CuO$_2$ planes. The critical current I$_c$ of I-Bi2212 is almost the same as of that of pristine crystals, but I$_c$ is much reduced in Hgl$_2$-Bi2212. In spite of expanded interlayer distances, the interlayer coupling is not significantly affected in I-Bi2212due to holes generated by iodine atoms. The coupling in HgI$_2$-Bi2212 is, however, weakened due to inertness of HgI$_2$ molecules and the expansion of interlayer distance. Relation between the superconducting transition temperature T$_c$ and the critical current I$_c$ seems to contradict Anderson's interlayer-pair-tunneling theory but agree with a modified version of it.

• Korean Journal of Materials Research
• /
• v.22 no.1
• /
• pp.16-23
• /
• 2012

Research into the development of high strength (1 GPa) and superior formability, such as total elongation (10%), and stretch-flangeability (50%) in hot-rolled steel was conducted with a thermomechanically controlled hot-rolling process. To improve the overall mechanical properties simultaneously, low-carbon steel using precipitation hardening of Ti-Nb-V multimicroalloying elements was employed. And, ideal microstructural characteristics for the realization of balanced mechanical properties were determined using SEM, EBSD, and TEM analyses. The developed steel, 0.06C-2.0Mn-0.5Cr-0.2(Ti + Nb + V), consisted of ferrite as the matrix phase and second phase of granular bainite with fine carbides (20-50 nm) in both phases. The significant factor of the microstructural characteristics that affect stretch-flangeability was found to be the microstructural homogeneity. The microstructural homogeneity, manifest in such characteristics as low localization of plastic strain and internally stored energy, was identified by grain average misorientation method, analyzed by electron backscattered diffraction (EBSD) and hardness deviation between the phases. In summar, a hot-rolled steel having a composition 0.06C-2.0Mn-0.5Cr-0.2(Ti + Nb + V) demonstrated a tensile strength of 998 MPa, a total elongation of 19%, and a hole expansion ratio of 65%. The most important factors to satisfy the mechanical property were the presence of fine carbides and the microstructural homogeneity, which provided low hardness deviation between the phases.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.498-502
• /
• 2010

Aluminium titanate($Al_2TiO_5$) has extremely anisotropic thermal expansion properties in single crystals, and polycrystalline material spontaneously microcracks in the cooling step after sintering process. These fine intergranular cracks limit the strength of the material, but provide an effective mechanism for absorbing strain energy during thermal shock and preventing catastrophic crack propagation. Furthermore, since machinable BN-ceramics used as an insulating substrate in current micro-electronic industry are very expensive, the development of new low-cost machinable substrate ceramics are consistently required. Therefore, cheap $Al_2TiO_5$-machinable ceramics was studied for the replacement of BN ceramics. $Al_2O_3-Al_2TiO_5$ ceramic composite was fabricated via in-situ reaction sintering. $Al_2O_3$ and $TiO_2$ powders were mixed with various mol-ratio and sintered at 1400 to $1600^{\circ}C$ for 1 h. Density, hardness and strength of sintered ceramics were systematically measured. Phase analysis and microstructures were observed by XRD and SEM, respectively. Machinability of each specimens was tested by micro-hole machining. The results of research showed that the $Al_2TiO_5$-composites could be used for low-cost machinable ceramics.

• Current Optics and Photonics
• /
• v.3 no.6
• /
• pp.541-547
• /
• 2019

A novel photonic crystal fiber (PCF) sensor with three D-shaped holes based on surface plasmon resonance (SPR) is analyzed in this paper. Three D-shaped holes are filled with the analyte, and the gold film is deposited on the side of three planes. The design of D-shaped holes with outward expansion can effectively solve the uniformity problem of metallized nano-coating, it is beneficial to the filling of the analyte and is convenient for real-time measurement of the analyte. Compared with the hexagonal lattice structure, the triangular arrangement of the clad air holes can significantly reduce the transmission loss of light and improve the sensitivity of the sensor. The influences of the air hole diameter, the distance between D-shaped holes and core, and the counterclockwise rotation angle of D-shaped holes on sensing performance are studied. The simulation results show that the wavelength sensitivity of the designed sensor can be as high as 10100 nm/RIU and the resolution can reach 9.9 × 10^-6 RIU.

• Journal of Powder Materials
• /
• v.24 no.2
• /
• pp.128-132
• /
• 2017

Harmonic structure materials are materials with a core-shell structure having a shell with a small grain size and a core with a relatively large grain size. They are in the spotlight because their mechanical properties reportedly feature strength similar to that of a sintered powder with a fine grain size and elongation similar to that of a sintered powder with a coarse grain size at the same time. In this study, the tensile properties, microstructure, and stretch-flangeability of harmonic structure SUS304L made using powder metallurgy are investigated to check its suitability for automotive applications. The harmonic powders are made by mechanical milling and sintered using a spark plasma sintering method at 1173 K and a pressure of 50 MPa in a cylindrical die. The sintered powders of SUS304L having harmonic structure (harmonic SUS304L) exhibit excellent tensile properties compared with sintered powders of SUS304L having homogeneous microstructure. In addition, the harmonic SUS304L has excellent stretch-flangeability compared with commercial advanced high-strength steels (AHSSs) at a similar strength grade. Thus, the harmonic SUS304L is more suitable for automotive applications than conventional AHSSs because it exhibits both excellent tensile properties and stretch-flangeability.

• Journal of the Korean Society of Food Culture
• /
• v.29 no.5
• /
• pp.428-436
• /
• 2014

This study was conducted to investigate the use of sugar alcohols (sorbitol, erythritol, and xylitol) as alternative sweeteners for replacing sucrose in Yukwa (traditional Korean oil-puffed rice snack). The moisture contents of Bandegi (dried Yukwa dough) and Yukwa containing sugar alcohols were higher than that of control (containing only sucrose). The microstructures of control and Bandegi containing sugar alcohols showed uniformly and finely distributed air holes. Expansion ratio and oil absorption of Yukwa containing sorbitol and 30% erythritol were higher than those of control. Appearance and cross section of control and Yukwa containing sorbitol, 30% erythritol, and 30% xylitol showed a good shape. The lightness (L) of control was significantly lower than Yukwa containing sugar alcohols, whereas redness (a) and yellowness (b) were higher than those in Yukwa containing sugar alcohols. Hardness of Yukwa containing sugar alcohols was significantly lower than that of control, and that of Yukwa containing sorbitol was the lowest. Peak number of Yukwa containing sugar alcohols was significantly lower than that of control, and that of Yukwa containing 60% erythritol and 60% xylitol was the lowest among all samples. In the sensory evaluation, color of control was deepest, whereas that of Yukwa containing 60% xylitol was lightest. Volume and air hole uniformity of Yukwa containing 60% erythritol and 60% xylitol were inferior than those of other samples. Sweetness of Yukwa containing sugar alcohols was lower than that of control, whereas oily flavor was stronger. Hardness of Yukwa containing sugar alcohols was lower than that of control, and Yukwa containing xylitol showed the lowest hardness among the samples. Crispness of Yukwa containing sugar alcohols was lower than that of control. There were no significant differences in overall acceptability between control and Yukwa containing 30% sorbitol and 30% erythritol. Overall, sorbitol and erythritol were appropriate as a 30% replacement for sucrose when preparing Yukwa.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.37 no.2
• /
• pp.133-136
• /
• 2011

Cystic lesions on the jaws with expansion can invade the adjacent anatomical structure, infiltrate and expand the jaws, cause facial deformity, etc. There is great potential for pathologic fractures after cyst enucleation, and damage to the major structures like the nerve, artery. For these reasons, marsupialization and decompression are commonly used to reduce the cystic size. In 1947, Thomas first mentioned decompression that reduces the osmotic pressure in a cyst by making a hole in the cyst and insert a drain. In our cases, a large sized cystic lesion was treated with a specific device made from an orthodontic band and spinal needle. This device is easy and effective for applications and self irrigation.

• The Journal of the Korea Contents Association
• /
• v.15 no.2
• /
• pp.21-30
• /
• 2015

Image coding based on mixed raster content model generates don't care regions (DCR) in foreground and background layers, and its overall coding performance is greatly affected by region filling methods for DCRs. Most conventional methods for DCR filling fail in utilizing the local signal properties in hole regions and thus the high frequency components in non-DCR regions are reflected into DCR after signal filling. In addition, further high frequency components are induced to the filled signal because of signal discontinuities in the boundary of DCR. To solve this problem, a new DCR filling algorithm using the priority-based adaptive region growing is proposed in this paper. The proposed method uses the watershed algorithm and the flooding priority of each pixel for region filling is determined from the degree of smoothness in the neighborhood area. By growing the filled region into DCR based on the computed priority, the expansion of high-textured area can be minimized which can improve the overall coding performance. Experimental results show that the proposed method outperforms conventional algorithms.