• The Journal of Engineering Geology
• /
• v.19 no.2
• /
• pp.153-163
• /
• 2009

In this study, a series of triaxial tests on Jeju basalt were carried out and then rock strength parameters were estimated by the Mohr-Coulomb failure criterion and the Hoek-Brown failure criterion using the test results. The characteristics of both failure criterions were investigated through comparing the estimated rock strength parameters. As the result of the Mohr-Coulomb criterion, the cohesions and the internal friction angles are determined as 5.35 MPa and $50.25^{\circ}$ of Pyoseonri basalt, 16.99 MPa and $60.66^{\circ}$ of Trachy-basalt, and 2.33 MPa and $37.05^{\circ}$ of Scoria, respectively. The cohesions and internal friction angles were estimated by the Hoek-Brown failure criterion in the basis of the results of regression analysis. The cohesions and the internal friction angles are determined as 4.77 MPa and $52.47^{\circ}$ of Pyoseonri basalt, 14.69 MPa and $60.70^{\circ}$ of Trachy-basalt, and 2.22 MPa and $47.60^{\circ}$ of Scoria, respectively. As the result of comparison between the Mohr-Coulomb failure criterion and the failure envelope predicted by the Hoek-Brown criterion, the cohesion estimated by the Hoek-Brown criterion is usually lower than that obtained from the Mohr-Coulomb criterion, whereas the friction angle estimated by the Hoek-Brown criterion is higher than that obtained from the Mohr-Coulomb criterion.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.7
• /
• pp.45-51
• /
• 2008

Triaxial compression tests on anisotropic rock specimens are carried out to investigate the failure strength characteristic of anisotropic rocks. The test core specimens were obtained in Daegu region. Test specimens are rock cores with the 7 different angles of bedding plane. The applied confining pressures were 5, 10, 20, 30, 40 MPa, and the rate of displacement was adopted 0.1%/min to fail the specimen within 5-15 min. The results were analyzed by using the failure criteria for anisotropic rocks proposed by Hoek & Brown (1980) and Jaeger (1960). The results of this study are summerised as follows: The results of inherent anisotropy show the shoulder type of anisotropy, and the effect of anisotropy is reduced as the confining pressure increases. The compressive strength of anisotropic rock shows the highest value at the ${\beta}$ (the angle of bedding plane) = $0^{\circ}$ and $90^{\circ}$ and the lowest value at $30^{\circ}$. The Hoek & Brown failure criterion for anisotropic rocks gives a relatively good agreement with the measured strength in all the range of ${\beta}$ angles, but the theory of Jaeger shows a reasonable agreement only in the range of ${\beta}=15^{\circ}$ and $45^{\circ}$.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.2
• /
• pp.13-20
• /
• 2001

외부하중의 작용방향에 의한 암반의 강도 및 변형이 달라지는 것을 강도 이방성, 또는 변형이방성이라 정의되어 진다. 강도 또는 변형 이방성은 층리진 퇴적압, 박층모양의 변성암, 균일하게 절리가 나있는 암석에서 흔히 볼 수 있다. 이러한 강도이방성에 대한 경험적 및 이론적 관점에서의 파괴 규준은 Jaeger(1960), McLamore와 Gray(1967), Donath(1972), Nova(1980), Hoek과 Brown(1980), Ramamurthy(1985)등 많은 학자들에 의해서 연구되어져 왔다. 본 논문에서는 셰일에 대한 삼축 압축시험을 통하여 층리각도에 따른 강도 이방성을 확인하고, 점착력, 내부 마찰각 및 재료상수의 물성치를 회귀분석을 통하여 구하였다. 또한, 수정된 Hoek과 Brown, Ramamurthy 등의 식을 통해 기존의 파괴규준식 및 수정된 식이 강도이방성적 특성을 나타내는 이 지역 셰일에 대한 적용가능성을 논하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1C
• /
• pp.25-31
• /
• 2006

It is common to use the unconfined compressive strength (UCS) of intact rock to estimate the shaft resistance of rock socketed drilled shaft. Therefore the most design manuals give a guide to use the UCS of rock core to estimate the shaft resistance of rock-socketed drilled shaft. Recently, however the design manuals for highway bridge (KSCE, 2001) and of AASHTO (2000) were revised to use the UCS of rock mass with RQD instead of the UCS of rock core so that the estimated resistance could be representative of field conditions. Questions have been raised in application of the new guide to the domestic main bed rock types. The intrinsic drawbacks in terms of RQD were comprised in the questions, too. As the results, in 2002 the new guide in the design manual for highway bridge (KSCE, 2001) were again revised to use the UCS of rock core to estimate the shaft resistance of rock-socketed drilled shafts. In this paper, various methods which can estimate the UCS of rock mass from intact rock core were reviewed. It seems that among those, the Hoek-Brown method is very reliable and practical for the estimation of the UCS of rock mass from rock cores. As the results, using the Hoek-Brown failure criterion a modified guide for the estimation of the shaft resistance of rock-socketed drilled shafts was suggested in this paper. Through a case study it is shown that the suggested method gives a good agreement with the measured data.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.11
• /
• pp.111-120
• /
• 2008

The characteristic of induced anisotropy is investigated in this study for the Pohang mudstone involving the cut plane discontinuity. The uniaxial and triaxial compression tests are performed for anisotropic rocks with artificial joint to look into anisotropic strength characteristics. Both the uniaxial compressive strength and triaxial compressive strength show the lowest value at the angle of cut plane, ${\beta}=30^{\circ}$ and the shoulder type of anisotropy is obtained. Anisotropy ratio (Rc) in uniaxial compression measures 9.0, whereas Rc=1.29-1.98 in triaxial compression is appeared. A series of analyses are made with the test results to derive the suitable parameter values when it is applied to the Ramamurthy (1985) failure criterion. The result of uniaxial compression test is analyzed by introducing the n-index into Ramamurthy failure criterion. The result shows that, n=l is suitable for ${\beta}=0^{\circ}{\sim}30^{\circ}$ and n=3 is suitable for ${\beta}=30^{\circ}{\sim}90^{\circ}$. To analyze the result of triaxial compression test by Ramamurthy failure criterion, anisotropy ratio in uniaxial compression test is added to Ramamurthy's equation and material constants are estimated by modified Ramamurthy's equation. When these values are applied back to Ramamurthy failure criterion, the predicted values are well fitted to the test results. And strength anisotropy for failure criteria of Jaeger (1960), McLamore & Gray (1967) and Hoek & Brown (1980) are also investigated.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.2 no.3
• /
• pp.25-36
• /
• 2000

The purpose of this research work is to propose an analytical method of tunnel design based on reasonable site data. Therefore the proposed design method consists of monitoring data and Modified In Situ Rock Model. Also the Rock Mass Rating for very poor quality rock is very difficult to estimate, the balances between the ratings may no longer gives a reliable basis for the rock mass strength. But in reality Rock Mass Rating is only the property which can be obtained from face mapping records of the exposed tunnel face during construction stage. Evaluation of rock parameters for the actual design prior to tunnel construction should be corrected during tunnelling process in particularly complex ground conditions. This study intends to investigate application of in-situ rock model to soft rock tunnelling (weathered rock) by face mapping results and site measurement data that are obtained at the costraction site of Seoul Subway Tunnel. For the preparation of more reliable ground parameters, the Rock Mass Rating values for the weathered rocks were modified and readjusted in accordance with the measurement data. The modified input parameters obtained by the proposed method are used for the prediction of the tunnel behavior at subsequent construction stages. The results of this study revealed that more reasonable feed back tunnel analysis can be possible as suggested. Ample measurement data would be able to confirm the new proposed technique in this research work.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.713-720
• /
• 2000

The directional response of strength and deformation on the rocks acting by external loads is called by strength and deformability anisotropy, respectively. Peak strength and its failure criteria of anisotro rocks have been studied and reported. Many authors have investigated in detail the behavior of triaxial peak strength of anisotropic rocks(Jaeger 1960, McLamore & Gray 1967, Hoek & Brown 1980, Ramamurthy & Rao 1985). They concluded that the triaxial strength of anisotropic rocks varies according to the inclination of discontinuity in specimens. And, the minimun triaxial strength occurs in the specmen with 60° of inclination angle ; and specimens with 0° or 90° inclination have maximum triaxial strength. Based on the experimental result, the behavior triaxial strength is investigated. The triaxial compression tests due to the angle bedding plane have been conducted and the material constants, 'm' and 's', cohesion and angle of friction and nonlinear strength parameters to fit for the failure criterion were derived from the regression analysis. And, the experimental date are employed to examine three existing failure criteria for peak strength, provided by Jaeger, McLamore and Hoek & Brown and Ramamurthy & Rao. For a shale, the suitability of the failure criteiria of triaxial peak strength for anisotropic rocks is discussed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.4C
• /
• pp.205-212
• /
• 2008

In this research, the effect of rock mass weathering on the side shear resistance of drilled shaft socketed into igneous-metamorphic rock was investigated. For that, 23 cast-in-place concrete piles with diameters varying from 400mm to 1,500mm were constructed at four different sites, and the static axial load tests were performed to examine the resistant behavior of the piles. A comprehensive field/laboratory testing program at the field test site was also performed to describe the in situ rock mass conditions quantitatively. The side shear resistance of rock socketed piles was found to have no intimate correlation with the compressive strength of the intact rock. However, the global rock mass strength, which was calculated by the Hoek and Brown criteria, was found to closely correlate to the side shear resistance. The ground investigation data regarding the rock mass conditions (e.g. $E_m$, $E_{ur}$, $p_{lm}$, RMR, RQD, j) were also found to be highly correlated with the side shear resistance, showing the coefficients of correlation greater than 0.75 in most cases. Additionally, the applicability of existing methods for the side shear resistance of weathered granite-gneiss was verified by comparison with the field test data. The existing methods which consider the effect of rock mass condition were modified and/or extended for weathered rock mass where mass factor j is lower than 0.15, and RQD is below 50%.