• Journal of dental hygiene science
• /
• v.15 no.3
• /
• pp.259-264
• /
• 2015

For this experiment, specimen was manufactured by injecting polymer and monomer into silicon mold with volume ratio of 2.5:1 based on ISO 20795-2 so that average thickness, width and length of specimen would be maintained as 3.3 mm, 10.0 mm and 65.0 mm, respectively depending on spray on technique. Specimen was divided into 3 groups ($25^{\circ}C$, $40^{\circ}C$, $70^{\circ}C$) depending on polymerization temperature and 10 specimen was manufactured for each group and it was polymerized in water tank of ${\pm}1^{\circ}C$ under the setting condition of polymerization time of 15 minutes and pressure of 3 bar. After keeping specimen in distilled water of $37^{\circ}C$ for over 48 hours before experiment, flexural strength (FS) and elasticity modulus (EM) of specimen being tested by using Intron (3344; Instron; Instron). SPSS ver. 16.0 was used for analysis and post-hoc test of Scheffe was performed after using one-way ANOVA. When comparing mean value of FS of resin for orthodontics, it was represented in the range of 71.500 MPa for $25^{\circ}C$ group, 74.920 MPa for $40^{\circ}C$ group and 76.880 MPa for $70^{\circ}C$ group and difference was shown in the order of $25^{\circ}C$ group <$40^{\circ}C$ group <$70^{\circ}C$ group but such difference was not significant statistically (p=0.052). Result of EM mean value of resin for orthodontics was more polymerization temperature was high, the more was significant difference represented in the order of $25^{\circ}C$ group <$40^{\circ}C$ group <$70^{\circ}C$ group (p<0.039).

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.3
• /
• pp.255-264
• /
• 2009

To evaluate the effects of chemical pretreatments of lignocellulosic biomass on enzymatic hydrolysis process, Populus euramericana was pretreated for 1 hr with 1% sulfuric acid ($H_2SO_4$) at $150^{\circ}C$ and 1% sodium hydroxide (NaOH) at $160^{\circ}C$, respectively. Before the enzymatic hydrolysis, each pretreated sample was subjected to drying process and thus finally divided into four subgroups; dried or non-dried acid pretreated samples and dried or non-dried alkali pretreated samples and chemical and physical properties of them were analyzed. Biomass degradation by acid pretreatment was determined to 6% higher compared to alkali pretreatment. By the action of acid ca. 24.5% of biomass was dissolved into solution, while alkali degraded ca. 18.6% of biomass. However, reverse results were observed in delignification rates, in which alkali pretreatment released 2% more lignin fragment from biomass to the solution than acid pretreatment. Unexpectedly, samples after both pretreatments were determined to somewhat higher crystallinity than untreated samples. This result may be explained by selective disrupture of amorphous region in cellulose during pretreatments, thus the cellulose crystallinity seems to be accumulated in the pretreated samples. SEM images revealed that pretreated samples showed relative rough and partly cracked surfaces due to the decomposition of components, but the image of acid pretreated samples which were dried was similar to that of the control. In pore size distribution, dried acid pretreated samples were similar to the control, while that in alkali pretreated samples was gradually increased as pore diameter increased. The pore volume which increased by acid pretreatment rapidly decreased by drying process. Alkali pretreatment was much more effective on enzymatic digestibility than acid pretreatment. The sample after alkali pretreatment was enzymatically hydrolyzed up to 45.8%, while only 26.9% of acid pretreated sample was digested at the same condition. The high digestibility of the sample was also influenced to the yields of monomeric sugars during enzymatic hydrolysis. In addition, drying process of pretreated samples affected detrimentally not only to digestibility but also to the yields of monomeric sugars.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.9
• /
• pp.840-850
• /
• 2010

The present study was attempted to find the effects of structural properties of phosphorus on the water quality of Gyehwa reservoir in Saemangeum. Relationship of phosphorus fractions between water and sediment properties was closely examined, and a few types of phosphorus were found from the sample sediment as : Saloid-P, Al-P, Fe-P, Ca-P, Red-P and Occd-P. Saloid-P (1.4%), Al-P (0.5%), Fe-P (39.8%), Ca-P (56.6%), Red-P (0.4%), Occd-P (1.3%) were extracted in a mass basis from the sediment of Gyehwa reservoir. Approximately more than 97% of phosphorus were calcium related phosphorus (Ca-P, 56%) and iron bound phosphorus (Fe-P, 39.8%). The Fe-P closely relates with water quality of T-N (r=0.761, p<0.05), $NO_3$-N (r=0.754, p<0.05), $NH_4$-N (r=0.728, p<0.05), T-P (r=0.774, p<0.05) and $PO_4$-P (r=0.767, p<0.05) while the Ca-P did not show any consistent dependency on the water quality. On the other hand, the correlation of Ca-P with $P_2O_5$ was high with r=0.783 (p<0.05) in the sediment. The Fe-P was affected significantly on the Ignition Loss (r=0.569, p<0.05), T-N (r=0.715, p<0.05) and T-P (r=0.983, p<0.01). In the research of correlation between phosphorus fraction and heavy metals in the sediment, Ca-P did not show any specific relationships with heavy metals. The Fe-P showed a significant correlation with As (r=0.817, p<0.01), Cu (r=0.793, p<0.05), Cd (r=0.786, p<0.05), Zn (r=0.738, p<0.05), so that it can be stated that the presence of Fe-P may implicate the volume of various metallic elements.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.3
• /
• pp.171-178
• /
• 2013

In this study, the sludge that occurs in the initial operation of coagulation system developed for the treatment of CSOs were returned to the flocculation reactor. The purposes of this study were to analyze the Characteristics of flocs that are generated through the recycling sludge and settling characteristics of sludge, and to evaluate the possibility that high concentrations of particulate matter in the initial inflow of CSOs could be used as an weighted coagulant additive. As a result, the concentration of treated CSOs pollutants at the beginning of the CSOs influent with a large amount of particulate matter over 20 ${\mu}m$ was low, after gradually increasing the concentrations of them. The flocs generated from the sludge return were similar in size compared to flocs generated through injection of micro sands, and settling velocity in case of return sludge injection was decreased from 55.1 cm/min to 21.5 cm/min. SVI value of the sludge accumulated at the bottom of the sedimentation tank was 72, and settled sludge volume decreased rapidly due to the consolidation of sludge to the time it takes to 10 minutes. these mean that sludge used for recycling has good settling characteristic. A condition of returned sludge which is 0.1% return of 0.3% extraction was formed in the balance of settlement and extraction. In this case, This condition was to be adequate to maintain the proper concentration such as 100~200 mg/L of TS and 50~100 mg/L of VS in the flocculation reactor. The usage of the return sludge containing particulate matters of CSOs as an weighted coagulant additive was able to secure a stable treated water quality despite the change of influent water quality dynamically. Furthermore, it can be expected to reduce the alum dosage along with the sludge production.

• Korean journal of applied entomology
• /
• v.16 no.3 s.32
• /
• pp.163-170
• /
• 1977

Potato diseases, especially mosaics and leaf roll, appear to reduce potato yield in Korea more than any other factor. A seed potato certification program was established at the Alpine Experiment Station (AES) in 1961 to produce high quality seed potatoes for distribution to Korean farmers. The present program for production of certified seed of Namjak (Irish Cobbler), the only variety recommended for spring plantings, is outlined. In 1976, approximately 10,000 MT of certified grade Namjak seed was produced by members of two Seed Producers Cooperatives in the Daekwanryeong area for distribution by the Office of Seed Production and Distribution (OSPD). The seed was inspected and certified by officers of the National Agricultural Products Inspection Office (NAPIO). Although the quality of the certified seed is far superior to that used by many farmers, the supply planted less than 1/5 of the 1977 potato crop. Certified seed of Shimabara, the variety recommended for autumn plantings, is not produced in Korea. The yield response of virus infected seed to improved cultural practices is poor. Therefore, an increase in potato acreage and yields appears to be possible only if more good quality seed is used by Korean farmers. A two or three fold increase in seed supply would be desirable. The volume of seed could be increased by expanding the production area and by improving yield in seed fields. More land is available in the alpine area and good seed potatoes could be grown in other parts of Korea. Planting better quality seeds and using better cultural pracitces would improve seed yields. Several techniques could be used to improve the quality of elite seed produced at AES. Changes in seed potato certification program should be made so that healthy seed stocks of new varieties can be released rapidly.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.91-93
• /
• 2003

A comprehensive numerical study is carried out to investigate for the understanding of the flow evolution and flame development in a supersonic combustor with normal injection of ncumally injecting hydrogen in airsupersonic flows. The formulation treats the complete conservation equations of mass, momentum, energy, and species concentration for a multi-component chemically reacting system. For the numerical simulation of supersonic combustion, multi-species Navier-Stokes equations and detailed chemistry of H2-Air is considered. It also accommodates a finite-rate chemical kinetics mechanism of hydrogen-air combustion GRI-Mech. 2.11[1], which consists of nine species and twenty-five reaction steps. Turbulence closure is achieved by means of a k-two-equation model (2). The governing equations are spatially discretized using a finite-volume approach, and temporally integrated by means of a second-order accurate implicit scheme (3-5).The supersonic combustor consists of a flat channel of 10 cm height and a fuel-injection slit of 0.1 cm width located at 10 cm downstream of the inlet. A cavity of 5 cm height and 20 cm width is installed at 15 cm downstream of the injection slit. A total of 936160 grids are used for the main-combustor flow passage, and 159161 grids for the cavity. The grids are clustered in the flow direction near the fuel injector and cavity, as well as in the vertical direction near the bottom wall. The no-slip and adiabatic conditions are assumed throughout the entire wall boundary. As a specific example, the inflow Mach number is assumed to be 3, and the temperature and pressure are 600 K and 0.1 MPa, respectively. Gaseous hydrogen at a temperature of 151.5 K is injected normal to the wall from a choked injector.A series of calculations were carried out by varying the fuel injection pressure from 0.5 to 1.5MPa. This amounts to changing the fuel mass flow rate or the overall equivalence ratio for different operating regimes. Figure 1 shows the instantaneous temperature fields in the supersonic combustor at four different conditions. The dark blue region represents the hot burned gases. At the fuel injection pressure of 0.5 MPa, the flame is stably anchored, but the flow field exhibits a high-amplitude oscillation. At the fuel injection pressure of 1.0 MPa, the Mach reflection occurs ahead of the injector. The interaction between the incoming air and the injection flow becomes much more complex, and the fuel/air mixing is strongly enhanced. The Mach reflection oscillates and results in a strong fluctuation in the combustor wall pressure. At the fuel injection pressure of 1.5MPa, the flow inside the combustor becomes nearly choked and the Mach reflection is displaced forward. The leading shock wave moves slowly toward the inlet, and eventually causes the combustor-upstart due to the thermal choking. The cavity appears to play a secondary role in driving the flow unsteadiness, in spite of its influence on the fuel/air mixing and flame evolution. Further investigation is necessary on this issue. The present study features detailed resolution of the flow and flame dynamics in the combustor, which was not typically available in most of the previous works. In particular, the oscillatory flow characteristics are captured at a scale sufficient to identify the underlying physical mechanisms. Much of the flow unsteadiness is not related to the cavity, but rather to the intrinsic unsteadiness in the flowfield, as also shown experimentally by Ben-Yakar et al. [6], The interactions between the unsteady flow and flame evolution may cause a large excursion of flow oscillation. The work appears to be the first of its kind in the numerical study of combustion oscillations in a supersonic combustor, although a similar phenomenon was previously reported experimentally. A more comprehensive discussion will be given in the final paper presented at the colloquium.

• The Korean Journal of Air & Space Law and Policy
• /
• v.23 no.2
• /
• pp.3-29
• /
• 2008

The volume of air passengers and cargo transportation has increased rapidly in recent years. This trend will be even more noticeable as the high-tech service industry expands and the globalization progresses. In an effort to reflect and to cope with this trend, many conventions concerning international air transportation have been concluded. The Republic of Korea has also acceded to the Montreal Convention of 1999 on September 20th, 2007 which became effective on December 29th 2007. However, Korea currently does not provide any private law on the liability of domestic air carrier, leaving the regulation wholly to the general conditions of carriage of private air lines. These general conditions of carriage, however, are not sufficient to regulate the liabilities of domestic air carriers, because they cannot be fully recognized as a legitimate source of law applicable in the court. This situation is inconvenient for both air carrier and their customers. Thus, the Ministry of Justice of Korea has decided to enact a law that will regulate domestic air transportation, namely, "Domestic Carriage by Air Act", as a part of the Korean Commercial Code. So was composed a special committee for legislation of the Domestic Carriage by Air Act. This writer has led the committee as a chairman. The committee has held in total 10 meetings so far and has completed a draft bill for the part VI of the Korean Commercial Code, "Air Carriage." The essentials of the draft are as follows: First, the establishment of Part VI in the Commercial Code. The Korean Commercial Code already includes a series of provisions on road transportation in part II and carriage by sea in part V. In addition to these rules regulating different types of transportation, the Domestic Carriage by Air Act will newly establish part VI to regulate air carriages. Eventually, the Commercial Code will provide an integrated legal system on the transportation industry. Second, the acceptance of the basic liability system which major international conventions, such as Montreal Convention of 1999 and Guadalajara Convention of 1961, have adopted. This is very important, because the law of air carriage is unified worldwide through various international conventions, making it necessary and significant for the new act to achieve conformity between rules of international air carriage and that of domestic air carriage. Third, the acceptance of Rome Convention system on damage caused by foreign aircraft to third parties on the surface. Fourth, the application of rules on domestic road carriage or carriage by sea mutatis mutandis with necessary modifications. This very point is the merit of inserting domestic air transportation law into the Commercial Code. By doing so, the number of articles can be reduced and the rules on air carriage can conform to that of road transportation and carriage by sea. The bill is expected to be passed by the parliament at the end of this year and is expected to be effective by end of July 2009.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.23 no.2
• /
• pp.232-237
• /
• 1994

Changes of volatile components in modified oleoresin red pepper during cooking at high temperature were investigated. Dried red pepper was milled to 100mesh of size particle and oily compounds were extracted by reduced pressure steam distrillation. The rest part was reextracted and concentrated. The extracts were combined. The same volume of water and 4% of polyglycerol condensed ricinoleate (PGDR) were added to the combined extract, and emulsified to make oleoresin red pepper 119 volatile compounds were separated from the dried red pepper and oleoresin and 35 components were identified in both samples. The major flavor compounds were identified to be 2-methoxy-phenol, 2, 6-bis(1, 1-dimethylethyl)-4-methyl-phenol, 1, 4-dimethylbenzene, thylbenzene, 1, 2-benzenedicarboxylic acid, 2-methoxyl-4-methylphenol, 4-ethyl-2-methoxy-phenol, and 5- methyl-2-furancarboxyaldehyde, and their transferal from raw red pepper to oleresin was low. 93 voltilie compounds were isolated after 3 hours cooking at 100 and 82 volitile compounds were separated after that at $150^{\circ}C$. Degeneration of volatile compounds was peculiarly proportional to the temperature of cooling. Capsaicin was relatively stable during cooking and remaining ratio after cooking at 100 and $150^{\circ}C$ was 84.7% and 73.3%. respectively. Oleoresin from red pepper had a little antioxidation effect at $100^{\circ}C$ cooking, but, antioxidation effect at $150^{\circ}C$ cooking was not shown due to degradation of capsaicin.

• Journal of Korean Society of Forest Science
• /
• v.94 no.6
• /
• pp.441-445
• /
• 2005

Researches on estimating national-scaled forest biomass are being carried out to quantify the carbon stock of forests with the Kyoto Protocol. In general, estimates of national-scaled forest biomass are based on forest inventory data which provides estimates of forest area, stem volume, and growth of stem by age classes. Estimates of forest biomass are, however, obtained by converting stem volumes to dry weight with stem density and thereafter to whole tree biomass with biomass expansion factors (ratios of whole tree dry weight to stem dry weight). Pinus densiflora is widely distributed and one of the most economically important timber species in Korea. The species are largely grouped into two ecotypes of Geumgang and Jungbu. Stems of Geumgang type trees are straight and high compared to those of Jungbu type trees. The objective of this study was to determine and compare stem density and biomass expansion factors fore two ecotypes of Pinus densiflora according to stand age. Stem density of both ecotypes of Pinus densora increased and biomass expansion factors of them decreased with increasing tree age. In he same age class, stem density and biomass expansion factor of Geungang type Pinus densiflora were lower than those of Jungbu type Pinus densiflora. There were statistically significant differences in stem density and biomass expansion factors between Geumgang type and Jungbu type Pinus densiflora in 0-20-year-old stands and 40-60-year-old stands. Our results suggested that the reliability of the national forest biomass inventory could be improved by applying the ecotype- and age-dependent stem density and biomass expansion factors.

• Journal of Korean Society of Forest Science
• /
• v.87 no.4
• /
• pp.631-641
• /
• 1998

The objectives of this study were 1) to classify the types of Quercus mongolica stands at Mt. Joongwang and compare their quality, and 2) to determine the proper future tree number of Q. mongolica per ha and the appropriate distance between the future trees. The results from this study were as follows : Q. mongolica stands at Mt. Joongwang was classified into four types, pure Q. mongolica stand as stand type I, Q. mongolica - hardwood stand as stand type II, Q. mongolica - Pines densiflora stand as stand type III, Hardwood - Q. mongolica stand as stand type IV, according to mixture rate in stand volume. Stand type IV showed the best quality stem of Q. mongolica among the stand types, and the stem quality of Q. mongolica in Q. mongolica stand mixed with hardwood as stand types II and IV was better than those in pure Q. mongolica stand as stand type I and in Q. mongolica - P. densiflora stand as stand type III. If the management goal for Q. mongolica stand is to produce its high quality-timber, it is desirable to sustain proper mixture rate of Q. mongolica with another hardwoods. The proper number of future trees in pure Q. mongolica stand as stand type I was 122trees/ha and reasonable distance between the future trees was 9.15m. The distance between future trees in other stand types was 7.2m to 9.3m for stand types II and IV, while 8.0m for stand type III. Thus, the classification of Q. mongolica stand type based on stand character and maturity, and proper stem number of future tree and optimum distance between future trees would be a useful forest tending work.