• Journal of the Korean Magnetics Society
• /
• v.2 no.3
• /
• pp.228-232
• /
• 1992

Magnetic properties of grain aligned high $T_c\;Y_1Ba_2Cu_3O_{7-y}$ superconductor are inverstigated. Grain-aligned superconductors have magnetic anisotropy in the Cu-O layer like single crystals. The lower critical field $H_{c1},$ measured at the temperature range of 2 K up to 77 K, is found to be decreasing linearly as temperature goes up. Moreover, it decreaes more rapidly when the Cu-O layer is perpendicular to the external magnetic field. The temperature dependence of the magnetic susceptibility shows that the value of magnetic susceptibility, $4{\pi}\;X,$ is close to -1 at low temperature. The intra grain critical current density $J_c,$ obtained from the Bean's critical state model, is found to be comparable to that of single crystal superconductors.

• Progress in Superconductivity
• /
• v.4 no.2
• /
• pp.184-188
• /
• 2003

Voltage-current characteristics of High Temperature Superconductor(HTS) tapes after applying the current beyond their critical current was investigated. When over-current is applied, the current begins to flow through the metal sheath instead of superconductor. The HTS tapes quenched were analyzed using V-I curve with various magnitudes of current. Two kinds of tapes were compared with each other to examine the influence of critical current on quench development. As a result, it was found that the resistance of superconductors and joule heat due to the over-current affect current distribution in HTS tapes. Critical current of HTS tapes was considered as a main factor deciding over-current characteristics.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.10
• /
• pp.1713-1719
• /
• 2008

A high temperature superconducting power cable (HTS power cable) was applied large current capacity by no resistance in normal state. Fault state was risen out of over-current but, it was limited to resistance. This study was modeling equivalence, and unbalanced state analyzed operating characteristic of HTS power cable. The equivalence model was composed superconductor, shield, and former part. This model simulation was appeared conductor and shield current in normal state, but unbalanced state was appeared former current as rise current by resistance. So it need to sufficiently influenced the quench characteristic when the former design.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.09a
• /
• pp.1-4
• /
• 2001

In electrophoresis, it is studied to get best condition of suspension media with alcoholic system for superconducting film. High-temperature superconductor films of $YBa_{2}Cu_{3}O_{7-x}$ were fabricated by electrophoretic deposition(EPD) from alcohol-based suspension. Maximum stability is observed for the suspension containing iso-alcohol as dispersion medium. However, for the formation of a dense and adherent coating of YBCO on a silver substrate by EPD. the best results were obtained in mixing PrOH and BuOH suspension. The superconducting critical current density($J_c$) was $1,200A/cm^2$ for the films deposited in 30% iso-PrOH and 70 % iso-BuOH suspension.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 1999.02a
• /
• pp.22-25
• /
• 1999

A well oriented Bi-2212 superconductor thick films were fabricated by screen printing with a Cu-free Bi-Sr-Ca-Cu-O powder on a copper plate and heat-treating at 820- $880^{\circ}C$for several minute in low oxygen pressure or are. At minute in low oxygen pressure of air. At , the printing layer partially melted by reaction between the Cu-free precursor by reaction between the Cu-free$870^{\circ}C$ precursor and CuO of the oxidizing copper plate. It is believed that the solid phase is Bi : Sr : Ca : Cu = 2 : 2 : 0 : 1. It is likely that the Bi-2212 superconducting phase is formed at Bi-2212 superconducting phase is formed at Bi-free phase/liquid interface by nucleation and grows.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.7
• /
• pp.1194-1198
• /
• 2010

A high temperature superconducting power cable (HTS power cable) was applied large current capacity by no resistance in normal state. Fault state was risen out of over-current but, it was limited to resistance. this study was modeling equivalence, and unbalanced state analyzed operating charateristics of HTS power cable. The equivalence model was composed superconductor, shield, and former part. This model simulation was appeared conductor and shield current in normal state, but fault state was appeared former current as rise current by resistance. so it need to sufficiently influenced the quench characteristic when the former design.

• Bulletin of the Korean Chemical Society
• /
• v.13 no.6
• /
• pp.663-665
• /
• 1992

The superconducting $YBa_2Cu_4O_8$ was synthesized in oxygen condition at 1 atm. The starting material with 1 : 2 : 4 composition was obtained by pyrolysis of EDTA complex, which was converted to 1-2-3 phase during densification, followed by the 1-2-4 phase recovery at $810^{\circ}C$ . The phase presents were identified by XRD, TG, DTA and AC magnetic susceptibility. Our data indicated that considerable amounts of 1-2-4 phase formed but with the 1 : 2 : 3 phase or possibly 2-4-7 as visible. As the P($O_2$) increased with temperature, impurity peak, CuO ($2{\Theta}$ = 38.8), gradually decrease, and we conclude that the 1-2-4 phase is predominant bulk superconductor under the high oxygen pressure.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1562-1563
• /
• 2011

Partial discharge measurement is one of the effective diagnostic techniques to predict abnormal high voltage dielectric insulation conditions of the electric equipments. Recently partial discharge diagnostic techniques were also utilized to evaluate the cryogenic dielectric insulation of high temperature superconducting electric equipment in liquid nitrogen. Generally, liquid nitrogen at 77 K is used used as the cryogenic and dielectric media for many high temperature superconducting high voltage applications. When a quench in the superconductor occurs, bubbles are generated which can affect the dielectric properties of the liquid nitrogen. So in order to reduce the bubble formation, subcooled nitrogen was also employed for this purpose. In this work, investigation of partial discharge characteristics of subcooled liquid nitrogen were conducted in order to clarify the retardation of partial discharge initiation voltage according to the different subcooling temperature of liquid nitrogen. And also the relation of partial discharge phenomena and the activities of bubbles were analyzed. It was observed that PD inception voltages shows rather different characteristics according to the decrease of subcooling temperature and the activities of bubbles were strongly influenced by temperature of the subcooled liquid nitrogen.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.6
• /
• pp.651-659
• /
• 2016

Korea Institute of Machinery & Materials (KIMM) has developed a high efficient Stirling cryocooler with moving magnet linear compressor for precooling hydrogen liquefier and cooling high temperature superconductor (HTS) devices, such as superconductor cable and superconductor fault current limiters. Hydrogen liquefier and HTS electric devices require cryocooler with cooling capacity of hundred watts to kilowatts at 77 K. The compressor in the Stirling cryocooler uses opposed moving magnet linear motors to drive opposed pistons. High efficient Stirling cryocooler is designed by SAGE-software, manufactured and tested systematically. A cooling capacity of 1 kW at 77 K with an electric input power of 9.6 kW has been analyzed. But prototype test results of the Stirling cryocooler have the cooling capacity of 0.65 kW at 76.8 K with an electric input power of 8.1 kW. And then, 21.5% Carnot COP (Coefficient of performance) of the prototype Stirling cryocooler is achieved. The comparison analysis between SAGE-model and experimental results has shown the direction for further design optimization of the Stirling cryocooler.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.603_604
• /
• 2009

HTS tape is developed for the purpose of being applied to the power cable, motor and generator, etc. The resistance of conventional power cables is not changed a lot by over current condition. But HTS(High temperature superconductor)power cable has some different properties. The impedance of superconductor is changed due to the magnitude of current, temperature, and magnetic field. And the characteristics analysis of HTS power cable under many kind of fault conditions are important to apply real system. In addition the magnitude of over current is 10 times larger than rated current. In this paper, the characteristics of HTS power cable are analyzed when over current flows. Model cable used 2G wires was made and experimented. The results will be helpful to manufacture real HTS power cable.