경주 금척리 유적은 5세기 후반에서 6세기 전반에 조성된 금척리고분군(사적 제43호)과 매우 연접하며, 유적이 위치한 지역은 그 일대의 유력 지배세력의 무덤으로 알려져 있다. 신라성장에 일익을 담당했던 인근 유적과도 밀접한 관련성이 있을 것으로 추정되는 경주 금척리 유적에서 출토된 철기를 대상으로 금속학적 방법론을 도입한 연구를 진행하였다. 철기의 용도에 따른 제작기법 차이를 확인하기 위해 용도별로 분류하여 8점을 선정하고, 미세조직 및 비금속개재물을 연구하였다. 분석 결과 제작 공정은 탄소함량이 높은 소재를 사용하여 형상을 단조하는 방법과 탄소함량이 낮은 소재를 사용하여 형상 단조만을 하는 기법, 형상 단조 후 필요에 따라 강도를 높이기 위한 침탄작업을 실시하는 기법이 적용된 것으로 확인된다. 이후 부위별 기능을 고려한 제강법과 열처리기술을 선택적으로 적용하여 기계적 성질을 향상시켰으며 제련공정에는 저온환원법이 적용되었을 가능성이 크다. 또한 경주 중심부와 외곽에 위치한 유적에서 출토된 철기 유물과 비교해본 결과 제련 및 제작기술에서 상호 유사한 것이 확인된다.
The purpose of this study was to examine the effect of temperature dependence of the behavior on the physical properties of posterior composite resins. Three light cure posterior composite resins (Heliomolar, Litefil-P, and P-50) and one chemical cure posterior composite resin (Bisfil-II) were used as experimental materials. Composite resin was placed in a cylindrical brass mold (2.5 mm high and 6.5 mm inside diameter) that was rested on a glass plate. Another flat glass was placed on top of the mold, and the plate was tightly clamped together. After the mold had been filled with the light cure composite material, the top surface was cured for 30 seconds with a light source. Chemical cure resin specimens were made in the same manner as above. Three hundreds and twenty composite resin specimens were constructed from the four composite materials. One hundred and sixty specimens of them were placed in a heater at $50^{\circ}C$, $75^{\circ}C$, $100^{\circ}C$, $125^{\circ}C$, $150^{\circ}C$, $175^{\circ}C$ and $200^{\circ}C$ for 5 minutes or 10 minutes respectively before compressive strengths were measured. Another one hundred and sixty specimens were tested for the diametral tensile strengths in the same way as above. They were randomly divided into eight groups according to the mode of heating methods as follows and stored in distilled water at $37^{\circ}C$ for 24 hours. Group $37^{\circ}C$ - specimens were stored at $37^{\circ}C$ in distilled water for 24 hours. Group $50^{\circ}C$ - specimens were heated at $50^{\circ}C$ after curing. Group $75^{\circ}C$ - specimens were heated at $75^{\circ}C$ after curing. Group $100^{\circ}C$ - specimens were heated at $100^{\circ}C$ after curing. Group $125^{\circ}C$ - specimens were heated at $125^{\circ}C$ after curing. Group $150^{\circ}C$ - specimens were heated at $150^{\circ}C$ after curing. Group $175^{\circ}C$ - specimens were heated at $175^{\circ}C$ after curing. Group $200^{\circ}C$ - specimens were heated at $200^{\circ}C$ after curing. Twenty specimens of each of four composite resins were respectively made by insertion of materials into same mold for examining the dimensional changes between before and after heating. The final eighty specimens were stored in distilled water at $37^{\circ}C$ for 24 hours before testing the dimensional changes. Compressive and diametral tensile strengths were measured crosshead speed 1mm/minute and 500Kg in full scale with a mechanical testing machine (DLC 500 Type, Shimadzu Co., Japan). Dimensional changes were determined by measuring the diametral changes of eighty specimens with micrometer (Mitutoyo Co., Japan). Results were as follows: 1. Diametral tensile strengths of specimens in all groups were increased with time heated compared with control group except for that in group $50^{\circ}C$ and the maximum diametral tensile strength was appeared in the specimen of Litefil-P heated for 10 minutes at $100^{\circ}C$. In heliomolar and P-50, it could be seen in the specimen heated for 10 minutes at $150^{\circ}C$, but in Bisfil-II, it could be found in the specimen heated for 5 minutes at $150^{\circ}C$. 2. Compressive strengths of specimens in all groups was tended to be also increased with time heated but that in group $50^{\circ}C$ and the maximum compressive strengths were showed in the same specimens conditioned as the diametral tensile strengths of four composite materials tested. 3. In Heliomolar, Litefil-P, and Bisfil-II, it was decreased in diameters of resin specimens between before heating and increased in diameters of resin specimens after storing in distilled water, but it was not in P-50. 4. There is little difference in diametral tensile strengths, compressive strengths, and dimensional changes followed by heating the resin specimens for 5 minutes and 10 minutes, but there is no statistical significances.
종이재(PA)와 대부분의 석탄회(FA)는 현재 매립에 의존하거나, 일부 시멘트의 대체재로 밖에 쓰이지 않는 폐기물로써, 이들을 자원으로 재활용한다면 환경을 보전할 뿐만 아니라 유용한 대체자원이 될 수 있는 장점이 있다. 본 연구에서는 점토를 30 wt%로 고정하고 폐기물의 양을 70 wt%로 하되, 폐기물내의 PA 대 FA의 비율은 $1:6{\sim}7:0$, 소결 온도는 $1150{\sim}1350^{\circ}C$ 범위내에서 변화시켜 제조된 소결체의 미세구조 및 물성을 분석하였다. 저온($1150{\sim}1200^{\circ}C$) 소결시에는 PA 첨가량이 증가할수록, 소결밀도가 증가한 반면, 높은 온도($1250{\sim}1350^{\circ}C$)에서 소결한 경우, PA첨가량이 증가할수록 과소결 현상이 발생하였고, 이로인해 미세구조가 불균일해지고 기공율이 증가되었다. 또한 시편의 기계적 특성은 미세구조의 균일성에 크게 좌우되었다. 예를들어 $1225^{\circ}C$에서 소결한 경우, 미세구조가 균일한 시편(10PA-60FA-30Clay)은 미세구조가 불균일한 시편(70PA-30Clay)에 비해 상대밀도값은 비슷하였으나 압축강도는 2배이상 높았다. 미세구조의 불균일성은 과소결에 인한 것으로 나타났다.
본 연구는 목질계 섬유판 제조에 있어 목섬유에 대한 도계부산물인 닭털의 부분적 대체화 가능성을 검토하기 위하여 수행하였다. 닭털은 주로 케라틴계 단백질로 구성되어 있으며, 외형적으로 목섬유와 큰 차이는 없었다. 닭털의 전처리 방법에 따른 포름알데히드 흡착능을 비교한 결과, 닭털을 고온/고압에서 처리하고 분쇄한 우모분에서 가장 높았다. 한편 일반 가위로 절단한 닭털과 이를 가정용 믹서로 고해시킨 닭털의 폼알데히드 흡착량을 dinitrophenylhydrazine법으로 측정한 결과 차이는 없었다. 닭털, 고해 닭털, 우모분을 각각 목섬유의 전건무게를 기준으로 5 wt%로 혼합하여 제조한 중밀도섬유판(MDF)의 물성과 폼알데히드방출량은 닭털의 전처리 조건에 영향을 받지 않았다. 그러나 이 측정치를 목섬유만으로 제조한 MDF와 비교하였을 때, 두께팽윤율과 폼알데히드방출량은 크게 개선되었다. 따라서 현재 생산 현장에서 적용되고 있는 요소수지를 이용한 MDF 제조에 있어 목섬유와 함께 일정한 양의 닭털, 고해 닭털 또는 우모분을 첨가할 경우 치수안전성과 폼알데히드방출량이 개선된 MDF의 제조가 가능할 것으로 예상된다. 그러나 MDF제조에 있어 닭털의 사용은 현재 상황에서 목섬유와 비교하여 원료 확보의 어려움과 높은 단가로 경제성이 낮은 것으로 조사되었다. 경제성 향상을 위하여 중소형 도계장에서 발생하는 닭털을 이용하거나, 동물성 사료의 금지에 대한 대비책 및 인플루엔자 감염 조류에 대한 환경적 처리 방안으로 닭털의 섬유판 원료에 대한 부분적 대체화 기술은 향후 사용 가능성이 충분할 것으로 판단된다.
Fully sealed field emission display in size of 4.5 inch has been fabricated using single-wall carbon nanotubes-organic vehicle com-posite. The fabricated display were fully scalable at low temperature below 415$^{\circ}C$ and CNTs were vertically aligned using paste squeeze and surface rubbing techniques. The turn-on fields of 1V/${\mu}{\textrm}{m}$ and field emis-sion current of 1.5mA at 3V/${\mu}{\textrm}{m}$ (J=90${\mu}{\textrm}{m}$/$\textrm{cm}^2$)were observed. Brightness of 1800cd/$m^2$ at 3.7V/${\mu}{\textrm}{m}$ was observed on the entire area of 4.5-inch panel from the green phosphor-ITO glass. The fluctuation of the current was found to be about 7% over a 4.5-inch cath-ode area. This reliable result enables us to produce large area full-color flat panel dis-play in the near future. Carbon nanotubes (CNTs) have attracted much attention because of their unique elec-trical properties and their potential applica-tions [1, 2]. Large aspect ratio of CNTs together with high chemical stability. ther-mal conductivity, and high mechanical strength are advantageous for applications to the field emitter [3]. Several results have been reported on the field emissions from multi-walled nanotubes (MWNTs) and single-walled nanotubes (SWNTs) grown from arc discharge [4, 5]. De Heer et al. have reported the field emission from nan-otubes aligned by the suspension-filtering method. This approach is too difficult to be fully adopted in integration process. Recently, there have been efforts to make applications to field emission devices using nanotubes. Saito et al. demonstrated a car-bon nanotube-based lamp, which was oper-ated at high voltage (10KV) [8]. Aproto-type diode structure was tested by the size of 100mm $\times$ 10mm in vacuum chamber [9]. the difficulties arise from the arrangement of vertically aligned nanotubes after the growth. Recently vertically aligned carbon nanotubes have been synthesized using plasma-enhanced chemical vapor deposition(CVD) [6, 7]. Yet, control of a large area synthesis is still not easily accessible with such approaches. Here we report integra-tion processes of fully sealed 4.5-inch CNT-field emission displays (FEDs). Low turn-on voltage with high brightness, and stabili-ty clearly demonstrate the potential applica-bility of carbon nanotubes to full color dis-plays in near future. For flat panel display in a large area, car-bon nanotubes-based field emitters were fabricated by using nanotubes-organic vehi-cles. The purified SWNTs, which were syn-thesized by dc arc discharge, were dispersed in iso propyl alcohol, and then mixed with on organic binder. The paste of well-dis-persed carbon nanotubes was squeezed onto the metal-patterned sodalime glass throuhg the metal mesh of 20${\mu}{\textrm}{m}$ in size and subse-quently heat-treated in order to remove the organic binder. The insulating spacers in thickness of 200${\mu}{\textrm}{m}$ are inserted between the lower and upper glasses. The Y\ulcornerO\ulcornerS:Eu, ZnS:Cu, Al, and ZnS:Ag, Cl, phosphors are electrically deposited on the upper glass for red, green, and blue colors, respectively. The typical sizes of each phosphor are 2~3 micron. The assembled structure was sealed in an atmosphere of highly purified Ar gas by means of a glass frit. The display plate was evacuated down to the pressure level of 1$\times$10\ulcorner Torr. Three non-evaporable getters of Ti-Zr-V-Fe were activated during the final heat-exhausting procedure. Finally, the active area of 4.5-inch panel with fully sealed carbon nanotubes was pro-duced. Emission currents were character-ized by the DC-mode and pulse-modulating mode at the voltage up to 800 volts. The brightness of field emission was measured by the Luminance calorimeter (BM-7, Topcon).
본 연구에서는 육가공 산업의 필수 공정인 냉동육 해동 시 발생하는 식육의 품질 저하를 최소화하기 위하여 진공 텀블링 해동 방식을 적용하고자 산업용 국산 임펠러-진공 텀블러(DVT, 6 ton)를 고안하고 이를 이용하여 해동한 냉동 돈육의 품질 특성을 현재 상업적으로 이용하는 자연해동(NTA)과 수입산 진공 텀블링 해동(IVT) 특성과 비교 분석하였다. 냉동 돈육(앞다리)의 자연해동 시간은 4,200분인데 반하여 DVT 해동은 165분이 소요되어 냉동 돈육 해동시간이 약 25배 단축되었다. 해동 시 돈육의 드립감량은 자연해동 2.08%에 비하여 DVT 해동은 0.85%로 낮아져 높은 해동 수율(99.2%)을 얻을 수 있었다. 자연 해동육에서 대장균군이 0.10±0.17 log CFU/g 수준으로 검출된데 반하여 DVT 해동육의 pH는 5.92, 총균수 1.96±0.01 log CFU/g, 대장균군 불검출로 높은 신선도를 보였다. 또한, DVT 해동육의 지방산패도(TBARS) 0.31±0.01 MDA mg/kg와 단백질변패도(VBN) 5.67±1.98 mg%를 보여 자연해동 돈육(각각 0.42±0.01 MDA mg/kg와 6.86±0.00 mg%)에 비해 지방과 단백질 변패도를 유의적으로 낮출 수 있는 것으로 나타났다. DVT 해동육의 보수력은 97.50±0.90%로 자연해동육(95.24±0.03%)에 비해 유의적으로 높았다. 자연해동(NTA) 후 조리한 돈육은 경도 212.03±0.02 N과 씹힘성 885.36±0.80이 진공 텀블링(DVT, IVT) 해동육에 비하여 각각 6.1배와 4.7배 높게 나타나 진공 텀블링 해동이 부드러운 조직감을 갖는 식육을 생산할 수 있는 것으로 나타났다. 해동육과 이를 가열조리한 돈육의 미세구조(SEM)를 관찰한 결과, 진공 텀블링 해동(DVT, IVT) 시료에서 근원섬유의 손상이 적어 섬유배열과 간격이 촘촘한 구조를 나타냈다. 본 연구에서 국내 최초로 고안한 산업용 대용량 진공텀블러는 해동 시 근육 조직의 손상을 최소화하여 보수력을 높이고, 드립감량을 감소시켜 부드러운 조직감과 함께 생산 수율을 높일 수 있을 뿐만 아니라 미생물학적 및 이화학적 변패도를 최소화할 수 있어 고품질의 육제품 생산에 활용될 수 있을 것으로 보인다. 또한, 본 장치는 수입산 진공텀블러와 비교해 우수한 품질의 해동육을 생산할 수 있어 본 연구자료를 이용한 국산 기술 자립화, 제품 품질 개선 및 수율 향상 등 육가공 산업 발전에 기여할 수 있을 것이라 사료된다.
가철성 상교정 장치에 많이 사용되는 자가중합형 상교정용 레진의 미반응 단량체는 레진의 물성과 생물학적인 면에 많은 영향을 끼친다. 따라서 미반응 단량체를 최소화하고 중합률을 최대로 하는 중합방법에 대한 연구는 중요한 의의를 갖는다. 저자는 자가중합형 상교정용 레진의 중합시간과 중합방법에 따른 중합률을 비교해보기 위해 시편을 다음과 같이 5군으로 나누어 연구를 진행하였다. 상교정용 레진의 분말과 용액을 혼합하여 제 1군은 $28^{\circ}C$의 공기중에 보관하였고, 제 2군은 $28^{\circ}C$의 물에, 제 3군은 $28^{\circ}C$의 물과 30psi의 압력에, 제 4군은 $43^{\circ}C$의 물에, 제 5군은 $43^{\circ}C$의 물과 30psi의 압력하에 각각 보관하였고, 10분, 1시간, 12시간, 1일, 3일 경과 후에 각 시편을 Fourier 변환적외선분광법을 이용하여 중합률을 측정하여 다음과 같은 결론을 얻었다. 1. 모든 군에서 중합시간이 경과함에 따라 중합률도 지속적으로 증가하는 양상을 보였다. 10분 경과 후의 결과와 비교하여 볼 때, 제 1군은 12시간 경과 후부터 중합률의 증가가 유의성이 있었고, 제 2군과 3군, 4군, 5군은 1시간 경과 후부터 유의성이 있었다(p<0.05). 2. 10분과 1일, 3일 경과 후에 제 5군, 제 4군, 제 3군, 제 2군, 제 1군의 순서대로 중합률이 높았다. 3. 중합시 온도에 따른 비교에서, 1일 경과 후를 제외하고는 모든 시간에서 $43^{\circ}C$에서 중합시킨 군의 중합률이 $28^{\circ}C$에서 중합시킨 군의 중합률 보다 유의성 있게 높았다(p<0.05). 4. 압력은 12시간 경과 후를(p<0.05) 제외하고는 중합률에 영향을 주지 못했다. 5. 보관방법은 1시간 경과 후를(p<0.05) 제외하고는 중합률에 영향을 주지 못했다.
본 연구에서는 물리적 강도가 뛰어나고 고온에서 안정하며 유연한 친환경 소재인 박테리아 셀룰로오스를 기반으로 투명 전도성막을 제조하였다. 전기전도성의 확보를 위해 은나노와이어(AgNW)와 그래핀을 도입하였다. 합성한 AgNW는 평균적으로 길이 약 $15{\mu}m$, 폭 약 70 nm로 종횡비 214이었다. 종횡비가 클수록 접촉저항을 낮추어 전도성을 개선시키게 된다. 총 7가지의 막을 제조하고 열적 및 전기적 물성을 조사하였다. 또 전도성막으로 제조하기 위해서 BC막을 칼로 길이 2 mm, 깊이 $50{\mu}m$ 간격으로 홈을 파서 직교상의 그물모양을 형성한 후 이 홈에 AgNW와 그래핀을 채워 넣었다. 대표적으로 AgNW 첨가막은 두께 $350{\mu}m$, 전자농도 $1.53{\times}10^{19}/cm^3$, 전자이동도 $6.63{\times}10^5cm^2/Vs$, 비저항 $0.28{\Omega}{\cdot}cm$로 가장 우수한 전기적 특성을 지닌 것으로 평가되었다. 또한 그래핀 첨가막은 두께 $360{\mu}m$, 전자농도 $7.74{\times}10^{17}/cm^3$, 전자이동도 $0.17cm^2/Vs$, 비저항 $4.78{\Omega}{\cdot}cm$이었다. 550 nm 광투과는 AgNW 첨가막 98.1%, 그래핀 첨가막 80.9%로 투명한 전도성 막이 형성되었다. 모든 막이 평면과 휜 상태에서 LED 점등 실험에서 전구의 밝기에 차이가 있었으나 불이 켜졌다. $150{\pm}5^{\circ}C$의 열판에서 박테리아 셀룰로오스 막은 형태가 매우 안정하였으나 같은 두께의 PET는 형태가 심하게 변형되었다. 이러한 연구 결과를 통해 박테리아 셀룰로오스 기반의 투명전도성막을 제조할 수 있는 가능성을 확인하였다.
본 연구에서는 국산재의 구조용집성재 라미나로의 이용을 위해 국산 소나무, 잣나무와 낙엽송 공시판재에 대하여 육안품질을 평가한 후, 레조르시놀수지와 수성고분자 이소시아네이트수지 접착제로 접착하여 제조한 단일수종 및 이수종 혼합 구조용집성재의 전단접착력과 접착내구성을 평가하였다. 국산재의 구조용집성재 라미나로의 이용을 위해 공시판재에 대한 육안품질등급 구분을 실시한 결과, 소나무, 잣나무 및 낙엽송의 육안품질 종합등급은 재내 잔존하는 크고 많은 옹이와 함께 큰 목리경사각으로 인해 낮은 등급의 판재 비율이 상당히 높게 나타났다. 좀더 높은 등급의 판재를 생산하기 위하여 가지치기 등의 육림작업과 할렬 및 비틀림 등의 결함을 줄이기 위한 제재 및 건조공정 개발이 필요할 것으로 판단되었다. 레조르시놀 수지 접착제와 수성고분자 이소시아네이트 수지 접착제로 제조된 단일수종 및 이수종 혼합 집성재의 전단강도는 $7.9{\sim}9.9N/mm^2$ ($80.9{\sim}101.3kgf/cm^2$) 범위 내에 있어 A수종군의 KS규격 전단강도인 $7.1N/mm^2$ ($72kgf/cm^2$)을 훨씬 상회하는 우수한 접착력을 나타내어 사용된 두 접착제 모두 강도적인 문제는 발생치 않을 것으로 판단되었다. 또한 레조르시놀 수지 접착제를 사용하여 제조한 단일수종 집성재와 이수종 혼합집성재의 침지 및 삶음박리시험 결과 모든 시험편이 KS 기준을 상회하여 접착내구성에도 역시 문제가 없음을 보여주었다. 그러나 수성고분자 이소시아네이트 수지 접착제로 제조된 단일수종 및 이수종 혼합 집성재의 침지와 삶음 박리율은 매우 높아 이 접착제를 구조용집성재용 접착제로 사용할 경우는 집성재의 사용환경을 신중히 고려하여야 할 필요가 있었다. 본 연구결과는 국산 소나무, 잣나무 및 낙엽송 단일수종 구조용집성재와 이수종 혼합집성재 제조를 위한 기초자료 제공 및 품질 향상에 사용될 수 있으리라 기대된다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.