• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.8A
• /
• pp.712-719
• /
• 2012

This paper presents Single-bit Third order Delta-Sigma Modulator, which can be applied to the Low speed High resolution ADC in Audio signal Process System. Whereas the Operational Amplifier in modulator consumed static power dissipation in operating, this modulator used Switching on/off techniques, which makes the Power dissipation of the modulator reduced. Also proposed modulator minimizes frequency characteristic variation by optimizing switch position. And this modulator chooses Single-bit type to guarantee stability. The designed ADC went through 0.35um CMOS n-well 1-poly 4-metal process to be a final product, and the final product has shown 17.1mW of power dissipation with 3.3V of Supply Voltage, 6.4MHz of conversion rate. And 84.3dB SNDR and 13.5bit ENOB with 20KHz of input frequency.

• Aerospace Engineering and Technology
• /
• v.9 no.1
• /
• pp.67-71
• /
• 2010

In this study, an algorithm for blind modulation detection in EDGE systems is presented. EDGE introduces an 8PSK modulation to provide high-speed data rates in addition to the existing GSM system. A transmitter may switch dynamically the modulation and coding schemes for transmission of data according to the channel quality. To decode the data correctly, the receiver has to detect using only training sequence which modulation is being used. Basically the property of one radio block composed of four bursts to detect effectively the modulation scheme even under severe conditions is used. More specifically, the reference value calculated for received burst is accumulated with previous reference value to minimize statistically the false detection probability in one radio block. Also each burst data having different modulation from the modulation of the fourth burst is set to zero to improve the decoding performance because the reference of the fourth burst has the highest reliability.

• Journal of Power Electronics
• /
• v.15 no.1
• /
• pp.146-159
• /
• 2015

Since the power capacity needed for the propulsion of large ships is very large, a multiphase AC induction propulsion mode is generally adopted to meet the higher requirements of reliability, redundancy and maintainability. This paper gives a detailed description of the development of a 20MW fifteen-phase PWM driver for advanced fifteen-phase propulsion induction motors with a special third-harmonic injection in terms of the main circuit hardware, control system design, experiments, etc. The adoption of the modular design method for the main circuit hardware design can make the enclosed mechanical structure simple and maintainable. It can also avoid the larger switch stresses caused by the multiple turn on of the IGBTs in conventional large-capacity converter systems. The use of the distributed controller design method based on a high-speed fiber-optic ring net for the control system can overcome such disadvantages as the poor reliability and long maintenance times arising from the conventional centralized controller which is designed according to point-to-point communication. Finally, the performance of the 20MW PWM driver is verified by experimentation on a new fifteen-phase induction propulsion motor.

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.11S
• /
• pp.3684-3693
• /
• 2000

In this paper, performance of a nonblocking high speed packet switch with switching capacity m which adopts a dynamic priority control function (DPCF) of a threshold- based Bernoulli priority jump (TBPJ) scheme is considered. Each input queue has two separate buffers with different sizes for two classes of traffics, delay-sensitive and loss-sensitive traffics, and adopts a TBPJ scheme that is a general state-dependent Bernoulli scheduling scheme. Under the TBP] scheme, a head packet of the delay-sensitive traffic buffer goes into the loss -sensitive traffic buffer with Hernoulli probability p according to systems states that represent the buffer thresholds and the number of packets waiting for scheduling. Performance analysis shows that TBPJ scheme obtains large performance build-up for the delay-sensitive traffic without performance degradation for the loss-sensitive traffic. In addition to, TBP] scheme shows better performance than that of HOL scheme.

• Journal of KIISE:Computer Systems and Theory
• /
• v.34 no.9
• /
• pp.425-434
• /
• 2007

Even though Internet backbone speeds have increased in the last few years due to projects like Internet 2 and NGI, many high performance distributed applications are able to achieve only a small fraction of the available bandwidth. The cause of such problem is due to a character of TCP/IP. The primary goal of this protocol is reliable data transmission. Therefore high speed data transmission didn't be considered when TCP/IP is designed. Hence several researchers have been studied in order to solve the problem of TCP/IP. One of these research results, parallel transfer technique, solves this problem to use parallel TCP connections on application level. Additionally, this technique is compatibility. Recently, these researchers have been studied a mechanism to decide the number of parallel TCP connections. However, some researchers reported the number of parallel TCP connection base on only empirical results. Although hardware performance of host affects transmission rate, the hardware performance didn't be considered in their works. Hence, we collect all data related to transmission rate, such as hardware state information (cpu utilization, interrupt, context switch). Then, we analyzed collected data. And, we suggest a new mechanism determining number of parallel TCP connections for maximization of performance based on our analysis.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.97-105
• /
• 2020

Recently, as the data speed and operating frequencies of Ethernet keeps increasing, electro magnetic interference (EMI) also becomes increasing. The generation of such EMI will cause malfunction of near electronic devices. In this study, EMI filters were applied to reduce the EMI generated by DC-DC SMPS (switching mode power supply), which is the main cause of EMI generation of Ethernet switch. As the EMI filter, MLCCs with excellent withstanding voltage characteristics were used, which had advantages in miniaturization and mass production. Two types of EMI MLCC filters were used, which are X-capacitor and X, Y-capacitor. X-capacitor was composed of 2 MLCCs with 10 nF and 100 nF capacity and 1 Mylar capacitor. Y-capacitor was consisted of 6 MLCCs with a capacity of 27 nF. When only X-capacitor was applied as EMI filter, the conductive EMI field strength exceeded the allowable limit in frequency range of 150 kHz ~ 30 MHz. The radiative EMI also showed high EMI strength and very small allowable margin at the specific frequencies. When the X and Y-capacitors were applied, the conductive EMI was greatly reduced, and the radiation EMI was also found to have sufficient margin. In addition, X, Y-capacitors showed very high insulation resistance and withstanding resistance performances. In conclusion, EMI X, Y-capacitors using MLCCs reduced the EMI noise effectively and showed excellent electrical reliability.

• The Korean Journal of Emergency Medical Services
• /
• v.14 no.3
• /
• pp.71-81
• /
• 2010

Purpose: To minimize an interruption in chest compression, reduce the hands-off time, the American Heart Association has recommended the ratio of chest compression to ventilation ratio to 30:2 from 2005 CPR guideline to 2010 CPR guideline. However, current studies have shown that the hands-off time was > 10 seconds with that method. For this reason, we devised new CPR method that a ventilation to chest compression ratio of 2:30 to reduce pt assessment time and skipped the assessment step of carotid artery pulse would be a more effective way to reduce the hands-off time & the time to set the CPR. According to the more detailed purpose are listed below. 1) We would like to confirm efficiency of a ventilation to chest compression ratio of 2:30 than a chest compression to ventilation ratio of 30:2 to reduce the hands-off time & the time to set the CPR. 2) We would like to evaluate possibility of increasing for chest compression accuracy of a ventilation to chest compression ratio of 2:30 than a chest compression to ventilation ratio of 30:2 3) We would like to evaluate possibility of increasing for ventilation accuracy of a ventilation to chest compression ratio of 2:30 than a chest compression to ventilation ratio of 30:2 Methods: According to 2005 American Heart Association Guidelines, 60 paramedic students(20 students X freshmen, sophomore, junior) performed 5 cycles of 3~ chest compressions : 2 ventilations after A, B, C evaluation with Laerdal Resusci R Anne SkillReporters. After 5 minutes rest, the 60 students performed 5 cycles of 2 ventilations : 30 chest compressions after A, B evaluation with the manikins between 13 and 17 September 2010. The short reports including speed & accuracy of chest compression, respiratory, CPR cycle were gained from the manikins. Hands-off times were measured by assistants. Results: Recently, the importance of high quality CPR was emphasized in order to perform the CPR faster and more accurate. To find out improving the conventional CPR method, we switch the procedure of the compression and the ventilation. By switching the procedure back and forth, we are able to compare the effectiveness of CPR between two type of CPR method which are 2:30 and 30:2 methods. 2:30 is that the breaths is delivered twice, first and perform 30 compressions while 30:2 perform 30 compressions first and give 2 breaths followed by the ABC method. Also, we verify the effectiveness of the hands off time, compression accuracy of the compression through the comparison of the two procedure as mentioned earlier. Consequently research verified that 2:30 is the efficient by providing faster set up delivering more accurate chest compression. Conclusion: 2:30 can minimize a time delay from cardiac standstill until starting the chest compression. In addition, hands-off time which is an interruption in chest compression can be shortened by 2:30 method, which result to effective oxygenation of coronary artery & maintenance of the bloodstream. Once again, performing the 2:30 method provide lessen hands off time and increase the accuracy of the chest compression.

• KDI Journal of Economic Policy
• /
• v.30 no.2
• /
• pp.225-270
• /
• 2008

We analyze macroeconomic consequences of pay-as-you-go (PAYGO) public pension system with a simple overlapping generations model. Contrary to large body of existing literatures offering quantitative results based on simulation study, we take another route by adopting a highly simplified framework in search of qualitatively tractable analytical results. The main contribution of our results lies in providing a sound theoretical foundation that can be utilized in interpreting various quantitative results offered by simulation studies of large scale general equilibrium models. We present a simple overlapping generations model with a defined benefit(DB) PAYGO public pension system as a benchmark case and derive an analytical equilibrium solution utilizing graphical illustration. We also discuss the modifications of the benchmark model required to encompass a defined contribution(DC) public pension system into the basic framework. Comparative statics analysis provides three important implications; First, introduction and expansion of the PAYGO public pension, DB or DC, result in lower level of capital accumulation and higher expected rate of return on the risky asset. Second, it is shown that the progress of population aging is accompanied by lower capital stock due to decrease in both demand and supply of risky asset. Moreover, risk premium for risky asset increases(decreases) as the speed of population aging accelerates(decelerates) so that the possibility of so-called "the great meltdown" of asset market cannot be excluded although the odds are not high. Third, it is most likely that the switch from DB PAYGO to DC PAYGO would result in lower capital stock and higher expected return on the risky asset mainly due to the fact that the young generation regards DC PAYGO pension as another risky asset competing against the risky asset traded in the market. This theoretical prediction coincides with one of the firmly established propositions in empirical literature that the currently dominant form of public pension system has the tendency to crowd out private capital accumulation.