• Smart Structures and Systems
• /
• v.21 no.5
• /
• pp.705-713
• /
• 2018

High-speed rail (HSR) has been in operation and development in many countries worldwide. The explosive growth of HSR has posed great challenges for operation safety and ride comfort. Among various technological demands on high-speed trains, vibration is an inevitable problem caused by rail/wheel imperfections, vehicle dynamics, and aerodynamic instability. Ride comfort is a key factor in evaluating the operational performance of high-speed trains. In this study, online monitoring data have been acquired from an in-service high-speed train for condition assessment. The measured dynamic response signals at the floor level of a train cabin are processed by the Sperling operator, in which the ride comfort index sequence is used to identify the train's operation condition. In addition, a novel technique that incorporates salient features of Bayesian inference and time series analysis is proposed for outlier detection and change detection. The Bayesian forecasting approach enables the prediction of conditional probabilities. By integrating the Bayesian forecasting approach with time series analysis, one-step forecasting probability density functions (PDFs) can be obtained before proceeding to the next observation. The change detection is conducted by comparing the current model and the alternative model (whose mean value is shifted by a prescribed offset) to determine which one can well fit the actual observation. When the comparison results indicate that the alternative model performs better, then a potential change is detected. If the current observation is a potential outlier or change, Bayes factor and cumulative Bayes factor are derived for further identification. A significant change, if identified, implies that there is a great alteration in the train operation performance due to defects. In this study, two illustrative cases are provided to demonstrate the performance of the proposed method for condition assessment of high-speed trains.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2263-2268
• /
• 2011

THE VIBRATION MODE OF RAILWAY VEHICLE IS DIFFICULT TO FIND OUT THE CHARACTERISTICS OF MOTION DURING THE OPERATION ON THE TRACK BECAUSE THESE HAPPEN TO INDEPENDENCE OR DUPLICATION MOTION CAUSED BY VEHICLE, WHEEL/RAIL INTERACTION, TRACK IRREGULARITY AND FAILURE OF THE SUSPENSION & POWER TRANSMISSION DEVICE ETC. IT IS NAMED AN ABNORMAL VIBRATION THAT THE VIBRATION, WHICH WAS PASSED THE PRIMARY AND SECONDARY SUSPENSION, IS AFFECTED TO THE PASSENGER OR DRIVER WITHOUT DAMPING. THIS PAPER DESCRIBES AN EXPERIENCE EVALUATION TO FIND OUT THE CAUSE OF AN ABNORMAL VIBRATION WHICH WAS HAPPEN AT THE CAB OF POWER CAR IN KTX-SANCHEON TRAINSET WHEN ON RUNNING AT HIGH SPEED ZONE.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.186-192
• /
• 2007

In general, pulsation damper is installed in fuel rail for conventional MPI engine to decrease undesirable noise in vehicle cabin room. However, pulsation damper is so expensive that there are prevailing studies to reduce fuel pressure pulsations with integrated damping effect. This paper is one of basic studies for development of fuel rail to abate pulsations with self-damping effect. Primarily, the pressure pulsation characteristics was investigated with aspect ratio of cross section, wall thickness, and materials of fuel rail. A high aspect ratio or thin wall was found to absorb the pressure pulsations effectively. But volume effects on the fuel pressure pulsation reductions were not especially significant than cross section effects because volume increment rate is larger than pressure pulsation reduction rate. The fuel rail made of aluminum is effective for reduction of pressure pulsation than that of low-carbon steel. Pressure change period increases on the basis of same lengths of supply line and fuel rail as the volume is enlarged and/or the thickness of wall is thinned.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.1653-1661
• /
• 2008

A trial run of locally-developed tilting train has been in process on Chungbuk line since the test vehicle was first produced. For the system stabilization, interface verification among the systems including track, structure, catenary and signaling system, not to mention the rolling stock, is very crucial. In the area of wayside structure, the stability of track structure and train run shall be evaluated through the review of impact by increased speed by developed train on track structure. The study thus was intended to evaluate the impact on track while a tilting train is running the conventional line(ballast track), which is vulnerable to accelerated train speed. The evaluation of tilting train test running the part of Honam line was conducted to identify the impact on existing track performance by tilting train. To identify the performance of each part of track components while tilting train and high speed train were running the existing line, wheel load, rail bending stress, vertical displacement of rail and sleeper were compared so as to evaluate the expected impact by tilting train for improving the train speed.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1305-1306
• /
• 2006

A new material was developed to achieve improvement of heat durability, improvement of wear resistance, stability of friction coefficient and reduction in aggression to counterpart, because it is difficult to maintain braking properties by using currently available materials in the train wagons used for high-speed transportation. As a result, the new material showed a stable wear resistance even in the speed range of 350km/h, where improvement was also confirmed in reduction of aggression to counterpart material by more than approximately 10%. This development was adopted for the brake lining in the Taiwan High Speed Rail project.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.7
• /
• pp.679-686
• /
• 2013

The reduction unit is one of the most important components in railway cars, due to the transmission of torque from the motor to the wheels. Faulty reduction gears in high-speed trains result from excessive wear on the gear or damage to the gear. These types of gear defects have a significant effect on high-speed rail operation and safety; thus, a diagnosis system for the reduction unit is needed. Vibration diagnosis technology is one of the most effective diagnostics. In this paper, the vibration parameters of a reduction unit were evaluated during a driving-gear test and a full-vehicle test, using kurtosis and the crest factor. These tests were performed under normal operating conditions; a specimen tester was used to diagnose problems in defective gears.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.11
• /
• pp.1602-1607
• /
• 2014

This paper deals with the design and property analysis of 7kW-class small-scaled superconducting Linear Synchronous Motor (LSM) and testing equipment for a number of performance pre-tests prior to the development of coreless-type superconducting LSM suitable for 600km/h very high speed train. First, the basic design and property analysis are conducted before developing a small-scaled superconducting LSM model with 2-pole superconducting electromagnets, and additionally the cost-down design of the superconducting electromagnets is conducted to use less high-Tc superconducting wire. Finally, the superconducting magnet coil span is selected at 120mm, and input ground armature current of 670Aturns is required to produce 44.7N of thrust based on research findings.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.138-143
• /
• 2006

Oscillatory wheel load fluctuation of considerable amplitude is almost always observed on railway vehicle running at high speed. From the acceleration measured on the axle-box, the frequency of this fluctuation is estimated to be approximately within 70 Hz. By the conventional measuring method, continuous outputs of wheel load can not be obtained, so it is difficult to investigate such a high frequency phenomenon exactly. We have developed a new method of measuring the forces and derailment coefficient continuously, using two pairs of strain gauge bridges whose output phases are shifted by 90 degree, and summing up the outputs with a weighting function. This method is available for measuring the forces between wheel and rail up to high frequency. In this paper, continuous method of measuring forces between wheel and rail and derailment coefficient.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.3-5
• /
• 2004

In order to speed up basic concept is to enhance high speed, curve limit speed, cross limit speed, acceleration/deceleration speed. It is important to optimal interface fundamental technology of vehicle, rail, electrical power, and signal system. Tilting train has advantage minimizing investment cost of infra railway system for increasing train limit speed in curve. the developed tilting train should be operated to commercial service speed 180Km/h of 200Km/h at KNR upgrade railroad. This paper proposed the basic model of system engineering for developing of TTX, tilting EMU (maximum operation speed : 180km/h) with speed-up of conventional railway system.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.26-29
• /
• 2004

In order to speed up basic concept is to enhance high speed, curve limit speed, cross limit speed, acceleration/deceleration speed. It is important to optimal interface fundamental technology of vehicle, rail, electrical power, and signal system. Tilting train has advantage minimizing investment cost of infra railway system for increasing train limit speed in curve. the developed tilting train should be operated to commercial service speed 180Km/h of 200Km/h at KNR upgrade railroad. This paper proposed the basic model of system engineering for developing of tilting EMU (maximum operation speed : 180km/h) with speed-up of conventional railway system.