• Journal of ILASS-Korea
• /
• v.16 no.3
• /
• pp.126-133
• /
• 2011

In HCCI Engine, combustion is affected by change of compression speed corresponding to engine speed. The purpose of this study is to investigate the mechanism of influence of engine speed on HCCI combustion characteristics by using numerical analysis. At first, the influence of engine speed was shown. And then, in order to clarify the mechanism of influence of engine speed, results of kinetics computations were analyzed to investigate the elementary reaction path for heat release at transient temperatures by using contribution matrix. In results, as engine speed increased, in-cylinder gas temperature and pressure at ignition start increased. And ignition start timing was retarded and combustion duration was lengthened on crank angle basis. On time basis, ignition start timing was advanced and combustion duration was shortened. High engine speed showed higher robustness to change of initial temperature than low engine speed. Because of its high robustness, selecting high engine speed was efficient for keeping stable operation in real engine which include variation of initial temperature by various factors. The variation of engine speed did not change the reaction path. But, as engine speed increased, the temperature that each elementary reaction would be active became high and reaction speed quicken. Rising the in-cylinder gas temperature of combustion start was caused by these gaps of temperature.

• Journal of the Korean Institute of Gas
• /
• v.4 no.2 s.10
• /
• pp.20-26
• /
• 2000

In this experimental study, we examined gas engine characteristics of a small high-speed engine in various ways. And we studied performance of natural gas, hydrogen gas and gasoline fuel engines, as emission characteristics and process of combustion. For the purpose of preventing back-fire occurred in case of high-speed and high load in hydrogen engine, we controlled air quantity by installing throttle valve in gas fuel engine. We performed experiment by mixing nitrogen to hydrogen fuel. As a result, we could find out characteristics which of a high speed small engine by applying gas fuels.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.219-222
• /
• 2003

Turbo generator system need starter for gas turbine engine. Turbo generator has high rate gearbox for reduce rotating speed. Because a conventional generator could not operate same speed of gas turbine engine. But Recently turbo generator system is directly connected a gas turbine engine with a super high-speed generator. In this paper, starter driver are implemented direct coupled turbo generator system, Which is directly connected 100kW, 60,000rpm gas turbine engine and 25kW 60,000rpm super high speed generator.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.5
• /
• pp.579-583
• /
• 1997

A diesel Engine rotates vibratively because of alternative explosion strokes. Traditional measurement of a diesel engine speed is carried out by measuring output voltage of FV convertor from input signals of MPU(magnetic pickup unit) or of DC tachometer. Because these measurement include also vibrative rotation of a diesel engine, an analog filter is often used to eliminate high frequency noises due to periodic explosion stroke. But by this method these high frequency noises do not eliminated effectively because noise frequencies are changed according to diesel engine speed. In this paper, author proposes a new measurement method of a diesel engine revolution which read digital signal directly from MPU and prove the utility of proposed method through the real experiment.

• Journal of the korean Society of Automotive Engineers
• /
• v.4 no.1
• /
• pp.20-30
• /
• 1982

Recent diesel engine has achieved high speed running comparable to that of gasoline engine as a speed improvement effort. Consequently, torsional vibration of high-speed diesel engine induced vibration nosise, reduced horsepower and the like. Viscous damper which is thought to be effective in curtailing the torsional vibration was studied over a wide range of speed. In this investigation, a water cooling, 4-cycle high-speed diesel engine(Msx. 3500 rpm)was used for the study. Theoretical analysis was made by assuming the engine to be an ideal equivalent system(length, moment of inertia) i. e. the multi-degree of freedom equivalent torsional vibration system with damper was analyzed. In the analysis, the inertia moment of suitable damper for this experiment was calculated by varying the relative damping coefficient of damper of engine for each damper. Furthermore, in the torsional vibration experiment, the torsional vibration amplitude of the crankshaft system was measured when the engine was equipped with dampers of different moments of inertia and also when the engine was equipped without dampers. The experimental results were compared with the analytical values and were found to be satisfied. The results of this investigation are summarized below; (1) It was found that for the engine equipped with dampers, the torsional vibration amplitude was reduced to about one third of those without dampers. (2) The optimum value of inertia moment of viscous damper for the engine was found to be about Id=1.05(kg.cm.s$^{2}$) (3) The optimum damping coefficient and the ratio of moment of inertia for the engine were found to be about Ca= 850(kg.cm.s), Rd=0.509, respectively (b1 dapmper).

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.287-291
• /
• 1992

Recently, electronic engine control system is used in many automotives for high efficiency and low pollution. In order to perform these requirements, fuel injection control, spark timing control, knock control, exhaust gas recirculation control and idle speed control should be implemented. In this paper, idle speed control system using microcontroller is developed, which is compact in hardware, but powerful in software performing efficient control and various compensations for engine condition and environments. If idle speed is low engine operation is not smooth, reversely if high, fuel consumption is increased. Therefore idle speed must be maintained as low as possible within the scope that ensures smooth operation of engine. Also, an engine signal simulator, which generates various signals from engine, is realized for test facility.

• Journal of information and communication convergence engineering
• /
• v.8 no.5
• /
• pp.534-538
• /
• 2010

Efficient control of a marine engine requires an engine control unit (ECU) system that handles fast and precise signal processes for in-coming and out-going signals from fast running engines. In order to handle these roles, the sequential control has been adapted in the ECU system in small and medium size ship engines, which has caused high production cost and complexity of the system. Hence, this paper is focused on developing an distributed ECU system for high speed and high precision control of a marine engine by efficiently combining a CPLD chip and a microprocessor. By sharing load at the MCU with the designed CPLD chip, we could achieve in driving a marine engine with high speed and precise control so that the ECU board has been simplified and its production cost has been reduced.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.54-64
• /
• 1995

The effects of swirl on early flame development and late combustion characteristic were investigated using a high speed single-shot visualized 51 engine. LDV measurements were performed to get better understanding of the flow field in this combustion chamber. Spark plugs were located at half radius (R/2) and central location of bore. High speed schlieren photographs at 20,000 frames/sec were taken to visualize the detailed formation and development of the flame kernel with cylinder pressure measurements. This study showed that high swirl gave favorable effects on combustion-related performances in terms of the maximum cylinder pressure and flame growth rate regardless of spark position. However, at R/2 ignition the low swirl shown desirable effects at low engine speed gave worse performances as engine speed increased than without swirl. There were distinct signs of slow-down in flame growth during the period when the flame front expanded from 2.5mm in radius until it reached 5.0mm apparently due to the presence of ground electrode. There seemed to be heat transfer effect on the flame expansion speed which was evidenced in high swirl case by the slowdown of the late flame front presumably caused by relatively large heat loss from burned gas to wall compared with low- or no-swirl cases.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.6
• /
• pp.87-94
• /
• 2003

This paper presents results of the development of the turbo generator system with structure which is HSG(High Speed Generator) installed directly to gas-turbine engine. Turbo generator with a high speed motor-generator directly has many advantages aspects of weight, size, lubrication system and complexity of the system compared of conventional turbo generator system with a gear box. But because of direct high speed operation of the high speed generator, we have to need stable high speed motor driving algorithm for perfect engine ignition when engine start. Also we have to need the design of the Power conditioning unit(PCU) for converting high speed AC output power to conventional AC power or needed DC power.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1078-1083
• /
• 2000

A high speed rotor balancing machine was developed, which is capable of balancing a flexible rotor in high speed. The machine is largely consisted of vacuum chamber, oil supply system and vacuum pump system. And, in order to investigate performances of the machine, various tests were carried. After high speed rotor balancing of gas turbine engine rotor using influence coefficient method, the flexible engine rotor passed smoothly through its critical speed.