• Journal of ILASS-Korea
• /
• v.25 no.1
• /
• pp.1-7
• /
• 2020

In the common rail fuel injection system, which is the core of diesel high efficiency and NO_X reduction, injection strategies such as high pressure injection of fuel, accurate injection rate control, and multistage injection are important to increase fuel atomization. In this study, the bypass type piezo injector for the electronic control based common rail injection system applied to diesel fuel vehicle was studied. In particular, the injection rate and internal fuel flow characteristics of the high-pressure injector according to the piezo stacking number and applied voltage were analyzed by theoretical numerical method. When the applied voltage changes, it is determined that additional fuel flow through the bypass compensates for the reduced valve driving force due to the change in the driving voltage.

• Journal of ILASS-Korea
• /
• v.12 no.3
• /
• pp.166-171
• /
• 2007

Recently, many studies on HSDI diesel engines have been performed to reduce the fuel consumption and $CO_2$ emission. One of the prominent technique to reduce emission is a high pressure multiple injection. For this technique, the injection rate is a critical parameter in order to determine precise injection duration and timing for combustion control. Thus the purpose of this study was to investigate relationship between the injection rate and the time-signature of chamber pressure at different injection pressure conditions in a common rail direct injection type injector using the Zeuch method. Using the measured correlation constants, estimated fuel injection rates are presented at many different injection conditions.

• Journal of Power System Engineering
• /
• v.18 no.6
• /
• pp.51-57
• /
• 2014

High pressure common rail injection technology has revolutionized the diesel industry. Over the last decade it has allowed engine builders to run higher injection pressures as much as above 1,300bar in order to increase engine efficiency, while reducing emissions. This common rail system has low pressure circuit which is consist of low pressure pump, cascade overflow valve and flow metering unit. The low pressure pump's purpose is to feed fuel oil to the high pressure pump. The cascade overflow valve keeps pressure in front of the metering unit constant and provides lubrication for the high pressure pump. The metering unit, known as the MPROP or fuel pressure regulator, regulates the maximum flow rate delivers to the rail. In this paper, we have investigated the performance characteristics of each components and total low pressure circuit of common rail system.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.05a
• /
• pp.77-85
• /
• 2000

LPG gains many advantages of a high octane number low emissions and low cost over conventional fuel. The fuel has been naturally used in engines to save running cost but the first generation fuel feeding system was not satisfied with stringent requirement for exhaust emissions, A liquid direct injection system into a cylinder has been suggested as a next generation system to maximize a fuel economy as well as to reduce emissions. In this paper LPG sprays are compared with diesel sprays in a high pressured surrounding condition in order to understand the high pressure spray characteristics, The spray images show that LPG spray penetrates further soon after the injection then the sprays stays in a distant. it may explain the flashing effect of LPG.

• Journal of ILASS-Korea
• /
• v.28 no.2
• /
• pp.89-96
• /
• 2023

This study presents a numerical simulation investigating hydrodynamic characteristics of high-temperature hydrocarbon aviation fuel injected through a plain orifice injector. The analysis encompassed the temperature range up to the critical point, and the obtained results were compared with prior experimental observations. The analysis unveiled that the injector's exit pressure remains equivalent to the ambient pressure when the fuel injection temperature is below the boiling point. However, when the fuel temperature surpasses the boiling point, the exit pressure of the injector transitions to the saturated vapor pressure corresponding to the fuel injection temperature. Consequently, the exit pressure of the injector increases in tandem with the rapid increase of the saturation vapor pressure due to escalating fuel temperatures. This rise in the exit pressure necessitates a proportional increase in fuel injection pressure to ensure a fixed fuel mass flow rate. Furthermore, the investigation revealed that the discharge coefficient obtained by applying the exit pressure instead of the ambient pressure did exhibit no decrease, but rather was maintained at a nearly constant value, comparable to its level below the boiling point.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.5
• /
• pp.31-38
• /
• 2009

Supercharging system was adopted to investigate the influence of boost pressure on operating range and exhaust emissions by using a supercharger at low temperature diesel combustion (LTC) condition in a 5-cylinder 2.7 L direct injection diesel engine. The experimental parameters such as injection quantity, injection timing, injection pressure and exhaust gas recirculation (EGR) rate were varied to find maximum operating range in LTC condition. As a result of adopting increased boost pressure in LTC, wider operating range was achieved compared with naturally aspirated condition due to increased mixing intensity. Increased boost pressure resulted in lower hydrocarbon (HC) and carbon monoxide (CO) emissions due to increased swirl rate and mixing intensity, which induced complete combustion. Moreover, increased boost pressure in LTC resulted in much lower soot emissions compared with high speed direct injection (HSDI) condition.

• Journal of ILASS-Korea
• /
• v.23 no.1
• /
• pp.22-29
• /
• 2018

The purpose of this study is to investigate the macroscopic spray characteristics and spray pattern of a gasoline direct injection (GDI) injector according to the increase of injection pressure. The macroscopic spray characteristics, such as a spray tip penetration and spray angle, were measured and analyzed from the frozen spray images, which are obtained from the spray visualization system including the high-speed camera, light-source, long-distance microscope (LDM). The spray pattern was analyzed through the deviation of the center of the spray plum and images were acquired using Nd: YAG Laser and ICCD(Intensified charge coupled device) camera. From the experiment and analysis, it revealed that the injection pressure have a significant influence on the spray tip penetration and spray pattern. However, the injection pressure have little influence on the spray angle. The increase of injection pressure induced the reduction of a closing delay. In addition, the deviation of spray center increase with the increase of injection pressure and the distance from a nozzle tip.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.3 s.234
• /
• pp.402-408
• /
• 2005

The instantaneous temperature behaviors on impinging plate in case of ultra high pressure have been measured and analyzed by using the instantaneous temperature probe and ultra high pressure injection equipment. The temperature drop was largest at P1 which is center of impinging spray and decreased with propagation of spray to the radius direction. The temperature drop was bigger in case of higher temperature of impinging plate. The temperature drop decreased with increase of injection pressure. But decreasing rate of temperature drop was slight over 2,500 bars. Therefore, it was predicted that the fuel evaporation versus the increase of injection pressure was maximum at around 2,500 bars.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.5
• /
• pp.790-796
• /
• 2012

Chip curling occurred during cutting process for difficult-to-cut material detracts product qualities and productivity. Among of method preventing the phenomenon, high pressure injecting cutting oil is an alterative. In this study, the optimal nozzle was designed by CFD method and it was conducted to analyse on the effect of high pressure injection on chip shape generated during cutting process and wear of insert by experimental method. As the result, it could be confirmed that high pressure injection is favorable for preventing chip curling and insert from wearing.

• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.1
• /
• pp.59-68
• /
• 2023

In this study, the performance of high-pressure fuel pumps was compared to find a high-pressure pump suitable for dimethyl ether (DME) fuel, and to establish a database of basic data on flow rates. The use of DME in compression ignition engines can reduce pollutant emissions. The cetane value of DME is higher than that of diesel fuel. The physical properties of DME are similar to liquefied gasoline gas (LPG), and when pressurized at a pressure of 6 bar or more, it changes from gas to liquid. Two types of high pressure pumps used in this study were independent injection type pump and a wobble plate type pump. Two high-pressure pumps with different injection types were compared. By measuring and comparing the performance changes of the two high-pressure pumps, a pump suitable for DME was selected and performance improvement measures were proposed. The changed experimental conditions to measure the performance change of the high pressure pump were increased in the units of 100 to 1,000 rpm and 100 rpm, and the experiment was performed at common rail pressures 300 and 400 bar. it was confirmed that the DME inside the fuel supply system remained in a liquid state through temperature sensors, pressure sensors, and pressure gauges. As a result of the experiment, it was confirmed that the flow rate discharged from the high-pressure fuel pump increased as the motor rotational speed increased, and the flow rate of the high-pressure fuel pump