• 한국축산식품학회지
• /
• 제18권2호
• /
• pp.176-184
• /
• 1998

The objective of this study was to investigate the effects of freezing rate on aroma retention and to examine the mechanism of aroma retention during freeze drying process. Our experiments were carried out with self-manufactured freeze-dryer. Gelatin gels (2% w / w, 80${\times}$20mm) containing diacetyl(2mg/ml) were frozen unidirectionally (Neumann's model) from the bottom at -45, -30, -20, and -15$^{\circ}C$ and followed with freeze-drying. Under the upper conditions we measured freezing rate and the change of temperature and pressure during freeze drying. Freeze-dried gelatins were cut horizontally into 5 mm thickness from the bottom measured and diacetly contents. Besides, we observed the effect of the relative humidity of the diacetyl contents freeze-dried gelatin during storage. The retained diacetyl content was increased at high freezing temperature and in order of 0∼5, 5∼10, 10∼15, 15∼20 mm section from the bottom of the sample. It was observed that the retained diacetyl content was high in 15∼20 mm section. The retained diacetyl content and freeze-dried gelatin stored in the condition of high relative humidity was decreased significantly but in the low relative humidity case, was it decreased in small amount. The results of our experiment resents that the low temperature freezing and low humidity storing condition is effective for preserving aroma compound in food.

• 한국생산제조학회지
• /
• 제9권3호
• /
• pp.83-89
• /
• 2000

In hydraulic control system turbine and gear motor type flowmeters are widely used to measure the flow rate under steady flow conditions. With the recent growth of interest in the measurement of instantaneous values of unsteady flow rate the test of the transient response of these flowmeters are in some significance. however an unsteady flow rate mea-surment and its calibration method with a fast response and a high accuracy have not beendeveloped. In this research particularly the dynamic characteristics of turbine and gear motor type flowmeters are investigated experimentally and simple mathematical models are proposed. The measured flow rate waveforms are compared with those by remote instan-taneous flow rate measurement method(RIFM) which has been developed by author and used for calibration As the result of frequency response test gain and phase between the measured flow rate waveforms by turbine type flowmeter and those estimated by RIFM are in good agreement up to 70Hz For the gear motor type flowmeter th simulated results by a math-ematical model proposed here agree well with the experiment nearly up to 100Hz. Also it if sound that the pressure drop across the flowmeter is increased in proportion to the frequency of the flow rate variation in a high frequency region of more than 100Hz. It can be explained that the dealy of gear motor type flowmeter in high frequency regionis mainly attributed to a first order delay consisting of the inertia of gears and internal leakage of the gear motor.

• 한국재료학회지
• /
• 제8권11호
• /
• pp.987-992
• /
• 1998

Ti 과 AI의 고순도 원소 박판을 이용하여 열간프레스장치에서 고온자전합성법으로 TiAI계 금속간화합물을 제조하였다. 원소 박판에서 $TiAl_3$ 금속간화합물을 제조하는 데 승온속도, 압력, 온도 등의 변수가 고온자전합성에 영향을 미치는 중요한 인자다. 특히 승온속도는 반응합성온도를 결정하는 인자로서 본 실험에서 DTA 분석을 이용하여 공정변수를 결정하였다. DTA 분석결과에 따르면, Ti와 AI의 계면에서 반응합성은 AI의 용융점 이하와 이상의 온도에서 두 번 발생함을 알 수 있다. 또한 승온속도가 증가할수록 두 반응합성온도는 증가하였다. 10층의 Ti 박판과 9층의 AI 박판을 $20^{\circ}C$/min의 승온속도로 고온자전합성시킨 후, $810^{\circ}C$와 240MPa의 압력에서 4시간 동안 열처리한 결과 $700\mu\textrm{m}$ 두께의 TiAI계 금속간화합물 판재를 제조하였으며, XRD 회절과 SEM으로 확인하였다.

• 한국초지조사료학회지
• /
• 제17권1호
• /
• pp.43-50
• /
• 1997

The aim of the study is to describe the fate and transformation of nitrogen in grassland ecosystems. Field experiments were conducted using sandyloam soil under variabling conditions: Zen, fertilization, reduced slurry application(l20kg N $ha^{-1}\;yr^{-1}$), usual sluny application (240 kg N $ha^{-1}\;yr^{-1}$).Soil water samples were gathered with 120cm ceramic cups with initial pressure of 0.5 bar. Samples were collected twice a month and analysed for NO, colormetrically. Percolation was calculated as the difference between precipitation and potential evapotranspiration, and leaching as the product of percolation and nitrate content of the water h m the ceramic cups. The N$H_4$-N content in soil had no significant effect on slurry application, but high slurry application on grassland resulted in high N$O_3$-N content in soil. The NO, concentration in soil water was remarkably variable during the year. The average N$O_3$, concentration during experiment became the lowest(8.5 mg/e ) without slurry application and highest with 240kOa cattle sluny(25.3 mg4 ). For each of the three different amounts of cattle sluny applied (0, 120, and 240kOa), the amount of N$O_3$-N leached per year were 12, 23 and 29kg/ha respectively. On grassland under the climatic conditions of Allgau showed enormous nitrate leaching, which has a p a t potential of polluting the ground water. The high pool of mineral N in the soil are the source for N$O_3$ leaching. The leaching of N$O_3$ cannot be avoided completely, but minimized by optimizing N fertilization rate.

• 한국표면공학회지
• /
• 제47권3호
• /
• pp.109-115
• /
• 2014

High power impulse magnetron sputtering (HIPIMS), also known as the technology is called peak power density in a short period, you can get high, so high ionization sputtering rate can make. Higher ionization of sputtered species to a variety of coating materials conventional in the field of improving the characteristics and self-assisted ion thin film deposition process, which contributes to a superior being. HIPIMS at the same power, but the deposition speed is slow in comparison with DC disadvantages. Since recently as a replacement for HIPIMS modulated pulse power (MPP) has been developed. This ionization rate of the sputtered species can increase the deposition rate is lowered and at the same time to overcome the problems to be reported. The differences between the MPP and the HIPIMS is a simple single pulse with a HIPIMS whereas, MPP is 3 ms in pulse length is adjustable, with the full set of multi-pulses within the pulse period and the pulse is applied can be micro advantages. In this experiment, $In_2O_3$ : $SnO_2$ composition ratio of 9 : 1 wt% target was used, Ar : $O_2$ flow rate ratio is 4.8 to 13.0% of the rate of deposition was carried out at room temperature. Ar 40 sccm and the flow rate of $O_2$ and then fixed 2 ~ 6 sccm was compared against that. The thickness of the thin film deposition is fixed at 60 nm, when the partial pressure of oxygen at 9.1%, the specific resistance value of $4.565{\times}10^{-4}{\Omega}cm$, transmittance 86.6%, mobility $32.29cm^2/Vs$ to obtain the value.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권4호
• /
• pp.67-74
• /
• 2015

본 연구에서는 슬래그를 다량 치환한 콘크리트의 동결융해 저항성능에 미치는 미세공극의 영향을 검토하였다. 콘크리트는 용선예비처리 슬래그가 포함된 고로슬래그 미분말을 0, 40, 70 % 치환하여 제조하였으며 압축강도 특성 및 동결융해 저항성능과 미세공극을 검토하였다. 또한 설계기준강도와 목표공기량을 설정하고, 동결융해 작용에 따른 열화를 확인하기 위하여 재령 14일의 낮은 압축강도로 인한 내력저하를 유도하였다. 실험결과, 설계기준강도를 유사하게 설정하고 목표공기량을 확보하였음에도 불구하고 콘크리트의 미세공극 분포가 상이한 결과를 나타내었다. GGBS70 시험체는 동결융해를 받지 않은 초기 0사이클에서 10~100 nm 크기의 공극량이 가장 적어 공극 내 동결할 수 있는 물의 양이 적을 것으로 판단된다. 이러한 이유로 다른 시험체에 비해 동결팽창압력이 상대적으로 작기 때문에 동결융해 저항성능이 우수한 것으로 판단된다.

• 동아시아식생활학회지
• /
• 제15권2호
• /
• pp.165-170
• /
• 2005

연근의 에탄올 추출물이 과당 유도 고혈압 백서의 신장 기능에 미치는 영향을 관찰하고자 뇨량과 전해질 배설량, 혈장의 creatinine, creatinine 청소율, 자유-수분 재흡수량 등을 측정하였다. 그 결과 연근은 과당 유도 고혈압 백서에서 나타나는 전해질 배설량의 변화를 개선시키는 효과는 없는 것으로 나타났고 단지 삼투질 농도의 배설량에만 약간의 개선 효과를 보였다. 신장의 가장 중요한 기능중 하나는 여과 기능이고 이를 나타내는 지표는 사구체 여과율인데, 고혈압 백서에서 혈장내 creatinine 농도가 증가하였고, creatinie 청소율이 크게 억제되었으나 연근추출물 투여 후 사구체 여과율의 감소가 회복되었다. 그러므로 연근은 과당으로 유도된 고혈압 흰쥐의 사구체 여과율을 개선시키는 것으로 사료된다.

• Journal of Welding and Joining
• /
• 제27권6호
• /
• pp.74-79
• /
• 2009

Titanium and titanium alloy can be reproduced immediately even if oxide films($TiO_2$) break apart in sea water. Therefore, since titanium demonstrates large specific strength and outstanding resistance to stress corrosion cracking, crevice corrosion, pitting and microbiologically influenced corrosion in sea water environment, it has been widely applied to heat exchanger for ships. In particular, with excellent elongation, pure titanium may be deemed as optimal material for production of heat exchanger plate which is used with wrinkles formed for efficient heat exchange. Conventional plate type heat exchanger prevented leakage of liquid through insertion of gasket between plates and mechanical tightening by bolts and nuts, but in high temperature and high pressure environment, gasket deterioration and leakage occur, so heat exchanger for LPG re-liquefaction device etc do not use gasket but weld heat exchanger plate for use. On the other hand, since welded plate cannot be separated, it is important to obtain high quality reliable welds. In addition, for better workability and production performance, lasers that can obtain weldment with large aspect ratio and demonstrate fast welding speed even in atmospheric condition not in vacuum condition are used in producing products. So far, 1st report and 2nd report compared and analyzed embrittlement degrees by bead colors of weldment through quantitative analysis of oxygen and nitrogen and measurement of hardness as fundamental experiment for the evaluation of titanium laser welding, and evaluated the welding performance and mechanical properties of butt welding. This study welded specimens in various conditions by using laser and GTA welding machine to apply edge welding to heat exchanger, and evaluated the mechanical strength through tensile stress test. As a result of tensile test, laser weldment demonstrated tensile strength 4 times higher than GTA welds, and porosity could be controlled by increasing and decreasing slope of laser power at overlap area.

• Design & Manufacturing
• /
• 제16권4호
• /
• pp.67-74
• /
• 2022

Injection molding is a cyclic process comprising of cooling phase as the largest part of this cycle. Providing efficient cooling in lesser cycle times is of significant importance in the molding industry. Recently, lots of researches have been done for rapid cooling of a hot-spot area using CO2 in injection molding. The CO2 flows under high pressure through small, flexible capillary tubes to the point of use, where it expands to create a snow and gas mixture at a temperature of -79℃. The gaseous CO2 removes heat from the mold and releases it into the atmosphere. In this paper, a CO2 cooling module was applied to an injection mold in order to cool a large area cavity uniformly and quickly, and the cooling performance of the injection mold was investigated. The product was a high-curvature molded part with a molding area of 300x100mm. Heat cartridges were installed in a stationary mold, and CO2 cooling module was inserted inside a movable mold. Through structural analysis, it was confirmed that the maximum deformation of mold with CO2 cooling module was 0.09mm. A CO2 feed system with a heat exchanger was used for cooling experiments. The CO2 was injected into the holes on both sides of the supply pipe of the cooling module and discharged through hexagon blocks to cool the mold. It took 5.8 seconds to cool the mold from an average temperature of 140℃ to 70℃. Through the experiment using CO2 cooling module, it was found that a cooling rate of up to 12.98℃/s and an average of 10.18℃/s could be achieved.

• Journal of Mechanical Science and Technology
• /
• 제16권11호
• /
• pp.1448-1456
• /
• 2002

The present study addresses the flow characteristics involved in the self-induced oscillations of the underexpanded jet impinging upon a cylindrical body. Both experiment and computational analysis are carried out to elucidate the shock motions of the self-induced oscillations and to find the associated major flow factors. The underexpanded sonic jet is made from a nozzle and a cylindrical body is placed downstream to simulate the impinging jet upon an obstacle. The computational analysis using TVD scheme is applied to solve the axisymmetric, unsteady, inviscid governing equations. A Schlieren system is employed to visualize the self-induced oscillations generated in flow field. The data of the shock motions are obtained from a high-speed video system. The detailed characteristics of the Mach disk oscillations and the resulting pressure variations are expatiated using the time dependent data of the Mach disk positions. The mechanisms of the self-induced oscillations are discussed in details based upon the experimental and computational results.