• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.317-320
• /
• 2010

In this study, the requirements for propellants to modulate the thrust of solid rocket motor were primarily investigated, followed by searching the research trends for propellants which would be feasible for the controlled solid rocket motor. And then, the theoretical performance and combustion characteristics of solid propellants being studied in ADD were demonstrated briefly.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.259-264
• /
• 2004

The critical component of combustor having high combustion efficiency for high performance liquid rocket engine is injector. The results of design and hot firing tests of six sub-scale combustors which have respectively an impinging type injector(1ea.), an bi-propellant swirl closed injector(1ea.), and hi-propellant swirl mixed injector(4ea.) were described in this paper. The combustion test were successfully performed. The combustion efficiency have higher value than predicted value and high frequency combustion instability does not occur.

• Journal of Aerospace System Engineering
• /
• v.14 no.3
• /
• pp.24-31
• /
• 2020

A study on the H2O2 based low toxic hypergolic propellant was conducted. The fuel candidates were chosen as a mixture of Amine solvent and reactive additive. The analytical performance was calculated via the NASA CEA code and 96% Isp of the NTO/UDMH was confirmed. The ignition delay measurement with drop test was performed and all candidates showed less than 10 ms in the best performance cases. Based on these results, the feasibility of high response H2O2 based low toxic hypergolic propellant was confirmed.

• Tribology and Lubricants
• /
• v.32 no.5
• /
• pp.154-159
• /
• 2016

This paper presents an experimental study of the leakage performance and endurance performance of a mechanical face seal in the 7-ton-class turbopump of the Korea Space Launch Vehicle 2 third-stage engine. We install a mechanical face seal between the fuel pump and turbine to prevent the mixing of the fuel and turbine gas. We design and manufacture a prototype mechanical face seal, which has two parts, namely, a bellows seal assembly and mating ring. We set up a test facility to measure the leakage and endurance of the mechanical face seal. For the similarity tests, we use water under real operating conditions such as high rotational speed, high temperature, and high pressure. Through investigation of the leakage and carbon wear rate, it is possible to evaluate the performance of the mechanical face seal. The results of the leakage and endurance performance test demonstrate the absence of any leakage from the prototype mechanical face seal after a trial run and clarify that the acceptable wear rate fully satisfies the turbopump requirements. Finally, we install a qualified mechanical face seal in a 7-ton-class turbopump and perform a validation test in the turbopump real-propellant test facility in the Korea Aerospace Research Institute. The test results confirm that the mechanical face seal works well under real operating conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.79-86
• /
• 2014

A turbopump real-propellant test facility(TPTF) is to verify the performance of a turbopump unit(TPU) based on liquid oxygen and kerosene. One of the most important sub-facilities is a hot-gas generation system which makes the driving force of the TPU with an alcohol burner. The alcohol burner generates the required flow rates and temperature at the facility using high pressure air and ethanol. In the study, the verification tests of the alcohol burner which was manufactured entirely with domestic technology were performed and fabrication technique and operation skill for the burner could be obtained ahead of the construction of the facility. Two burners will be operated simultaneously for the real-propellant test of 75tf class turbopump and satisfy the power requirement from the turbine of the TPU.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.4
• /
• pp.46-58
• /
• 2010

Hydrogen peroxide(HP) and liquid methane have deserved renewed considerations as green propellants in recent years, because main design concerns in the development of the new generation propulsion system for spacecrafts are concentrated on low operation cost and environmental cleanness. Although HP has a long history of application to aerospace propulsion systems due to high density, mono-propellant characteristics and low toxicity, it had been replaced by hydrazine and liquid oxygen due to extreme performance requirement during the cold war. But HP has received a renewed interest due to its increased stability and many researches have been conducted to develop high performance LREs(Liquid Rocket Engines) using HP. Liquid methane has also received a new interest in rocket propulsion system for the future space exploration according to its possibility of ISRU(In-Situ Resource Utilization).

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.1
• /
• pp.1-8
• /
• 2015

Micro igniter on the glass membrane for MEMS thruster was developed. The stability of the micro igniter by using a glass membrane with a thickness of tens of microns was improved. The micro igniter was fabricated by anisotropic wet etching of photosensitive glass and deposition of Pt/Ti for electric heat coil. The solid propellant was loaded into the propellant chamber without an especial technique due to the high structural stability of the glass membrane. Ignition tests were performed successfully. The minimum ignition delay was 27.5 ms with an ignition energy of 19.3 mJ.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.373-376
• /
• 2010

The characteristics of thermal-resistance catalyst for $N_2O$ propellant decomposition were studied in the present study. Si was added to the $Al_2O_3$ support to stabilize its surface area at high temperature (> $1000^{\circ}C$). Ru was used as a catalyst for $N_2O$ decomposition. The prepared catalysts were characterized using SEM, EDS and XRD analysis, and $N_2O$ conversion was measured as reaction temperatures. The Ru/$Al_2O_3$-Si catalyst showed better performance than Ru/$Al_2O_3$ catalyst.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.2
• /
• pp.72-82
• /
• 2017

Nozzleless booster is one of the applicable components for integral rocket ramjet (IRR). In order to predict nozzleless solid booster performance, the simplified theoretical analysis was applied for L/D=5, 6, 7, 9, 11, and 13. Al-HTPB and Zr-HTPB propellant with a high metal content were used to increase the hardness because of the combustion gas flow effect. It was found that the trends between the simplified theoretical analysis and experiments were similar.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.58-61
• /
• 2009

The characteristics of nitrous oxide catalytic decomposition were studied to utilize the nitrous oxide as a propellant. The Ru and Pt were selected as nitrous oxide decomposition catalysts and loaded in the $Al_2O_3$ support using an impregnation method. The nitrous oxide conversions as a variation of GHSV and reaction temperature were measured in a tubular reactor. At the low GHSV and high temperature, the conversion was increased, and Ru/$Al_2O_3$ catalyst showed better performance than Pt/$Al_2O_3$ catalyst.