• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.3
• /
• pp.214-222
• /
• 2015

The superiority of gallium nitride FET (GaN FET) over silicon MOSFET is examined in this paper. One of the outstanding features of GaN FET is low reverse-recovery charge, which enables continuous conduction mode operation of totem-pole bridgeless boost power factor correction (PFC) circuit. Among many bridgeless topologies, totem-pole bridgeless shows high efficiency and low conducted electromagnetic interference performance, with low cost and simple control scheme. The operation principle, control scheme, and circuit implementation of the proposed topology are provided. The converter is driven in two-module interleaved topology to operate at a power level of 5.5 kW, whereas phase-shedding control is adopted for light load efficiency improvement. Negative bias circuit is used in gate drivers to avoid the shoot-through induced by high speed switching. The superiority of GaN FET is verified by constructing a 5.5 kW prototype of two-module interleaved totem-pole bridgeless boost PFC converter. The experiment results show the highest efficiency of 98.7% at 1.6 kW load and an efficiency of 97.7% at the rated load.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.6
• /
• pp.241-249
• /
• 2012

In the many countries, research about ultra wideband wireless transmission technique is widely studied for efficient utilization of frequency resource due to a sudden increase of demand of frequency resource all over the world. The ultra wideband communication system has the some specific advantages. First, it can transmit data with high speed, second short transmission range can increase the frequency reuse rate, and finally it has high security property. However, there is a interference between ultra wideband system and other communication system but study to solve this problem is insufficient. To efficient utilization of limited frequency resource, a novel frequency avoidance technique and setup the standardization of frequency interference must need. So, the purpose of this paper is that increases communication efficiency of microwave communication systems to analyze the technical trends for transmission of the low power device, and to research the implementation and technical research of wireless access network technique of wideband communication systems.

• Journal of Internet Computing and Services
• /
• v.2 no.1
• /
• pp.49-61
• /
• 2001

Internet has been becoming widely popular and making rapid progress and network technologies is showing extension in data transmission speeds. Rapid and convenient multimedia services supplied with high quality and high speed are being needed, This paper treats of the design and implement method of clip-based video retrieval system on the world-wide-web environments. The implemented system consists of the content-based indexing system supporting convenient services for video contents providers and the web-based retrieval system in order to make it easy and various information retrieval for users on the world-wide-web. Three important methods were used in the content-based indexing system. Key frame extracting method by dividing video data, clip file creation method by clustering related information and video database build method by using clip unit, In web-based retrieval system, retrieval method by using a key word, two dimension browsing method of key frame and real-time display method of the clip were used. As a result. the proposed methodologies showed a usefulness of video content providing. and provided an easy method for searching intented video content.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.1
• /
• pp.38-48
• /
• 1996

We implemented and evaluated the preformance of a task level pipelined multicomputer "RV860-PIPE(Realtime Vision i860 system using PIPEline)" for computer vision applications. RV860-PIPE is a message-passing MIMD computer having ring interconnection network which is appropriate for vision processing. We designed the node computer of RV860-PIPE using a 64-bit microprocessor to have generality and high processing power for various vision algorithms. Furthermore, to reduce the communication overhead between node computers and between node computer and a frame grabber, we designed dedicated high speed communication channels between them. We showed the practical applicability of the implemented system by evaluting performances of various computer vision applications like edge detection, real-time moving object tracking, and real-time face recognition.

• Journal of Advanced Navigation Technology
• /
• v.18 no.6
• /
• pp.600-608
• /
• 2014

In this paper, CABAC H/W module is developed using co-design method. After entire H.264/AVC encoder was developed with C using reference SW(JM), CABAC H/W IP is developed as a block in H.264/AVC encoder. Context modeller of CABAC is included on the hardware to update the changed value during binary encoding, which enables the efficient usage of memory and the efficient design of I/O stream. Hardware IP is co-operated with the reference software JM of H.264/AVC, and executed on Virtex-4 FX60 FPGA on ML410 board. Functional simulation is done using Modelsim. Compared with existing H/W module of CABAC with register-level design, the development time is reduced greatly and software engineer can design H/W module more easily. As a result, the used amount of slice in CABAC is less than 1/3 of that of CAVLC module. The proposed co-design method is useful to provide hardware accelerator in need of speed-up of high efficient video encoder in embedded system.

• Journal of Advanced Navigation Technology
• /
• v.18 no.6
• /
• pp.541-545
• /
• 2014

Rec. ITU-R M.1842-1 is international recommendation for VHF band communication guideline in maritime mobile service RR Appendix 18 channels. In this paper, we simulate 28.8 kbps VHF ${\pi}$/4-DQPSK digital baseband modem compatible with the recommendation, then it is designed and implemented with FPGA. Cazac sequence is used as a preamble since packet format is not defined untill now in the recommendation. Baseband modem is designed by VHDL language and implemented on NEXYS4 development platform having Atrix7 FPGA chip from Xilinx. For wireless communication test of total prototype system, ADC/DAC board is implemented and EV9730 RF module is utilized. From the experimental results, implemented FPGA modem shows spectral bandwidth of 25 kHz and successful data exchanges between tx and rx communication platform.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.5
• /
• pp.1031-1038
• /
• 2005

In this paper, we propose real-time 3D image converting architecture by a unit of pixel for 2D/3D compatible PC and LCD of cellular phone with parallax burier, and implement a system for overall display operation after designing a circuit based on FPGA. After digitizing anolog image signal from PC, we recompose it to 3D image signal according to input image type. Since the architecture which rearranges 2D image to 3D depends on parallax burier, we use interleaving method which mixes pixels by a unit of R, G, and B cell. The propose architecture is designed into a circuit based on FPGA with high-speed memory access technique and use 4 SDRAMs for high performance data storing and processing. The implemented system consists of A/D converting system, FPGA system to formatting 2D signal to 3D, and LCD panel with parallax barrier, for 3D display.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.83-89
• /
• 2011

Diesel engines can produce higher fuel efficiency and lower $CO_2$ emission, they are subject to ever more stringent emission regulation. However, there are two major emission concerns fo diesel engines like such as particulate matter (PM) and nitrogen oxides (NOx). Moreover, it is not easy to satisfy the regulations on the emission of NOx and PM, which are getting more strengthened. One of the solutions is to apply the new combustion concept using multistage injection such as HCCI and PCCI. The other solution is to apply after-treatment systems. For example, lean NOx trap catalyst, Urea-SCR and others have various advantages and disadvantages Especially, Urea-SCR system have advantages such as a high conversion efficiency and a wide operation conditions. Hence the key factor to implementation of Urea-SCR technology, good mixing of urea(Ammonia) and gas, reducing Ammonia slip. Urea mixer components are required to facilitate evaporation and mixing because the liquid state of urea poses significant barriers for evaporation, and the distance to mixer is the most critical that affect mixer performance. In this study, to find out the distance from injector to mixer and simulation factor, a laser diagnostics and high speed camera are used to analyze urea injector spray characteristics and to present a distribution of urea solution in transparent manifold In addition, Droplet Uniformity Index is calculated from the acquired images by using image processing method to clarify the distribution of spray.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.73-81
• /
• 2011

As high speed digital systems continue to use components with faster edge rate and clock speeds, transmission of the digital information, it can bring about many troubles. The increasing requirement for controlled impedance PCBs becomes both a critical success factor and a design challenge to implement a system. Especially, the noise sources in high frequency digital systems include the noise in power supply, ground and packaging, and they destroy the fidelity of signals. Therefore PCB design with impendence matching is needed to improve fidelity of signal in H/W. In this paper, we have developed an impedance control and analysis tool for multi-layer PCB design, and simulates the tracks controlled impedance with the test coupon. So, it can save the design time and support the economical PCB design.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.10
• /
• pp.1137-1146
• /
• 2008

OFDM is very effective for the high speed communication system. However, OFDM has the problems of high PAPR and serious ICI, which is different from the single carrier system. Especially, ICI problem caused by phase noise, Doppler effect and frequency offset is main reason for poor performance since it breaks down the orthogonality between subcarriers in OFDM communication system. Therefore, WFMT modulation scheme is studied and the effect of the carrier frequency offset and phase noise is analyzed. WFMT modulation scheme is based on the wavelet theory and complex filter banks for synthesis and analysis of multichannel signal. WFHT modulation scheme keeps on the advantage of filter banks system and can be easily possible for the implementation of filter banks. In this paper, we compare ISI and ICI distortions of the WFMT and OFDM system due to the carrier frequency offset and phase noise. Also, we analyze the PAPR and BER performances in the HPA and ICI situation caused by the Doppler frequency shift and the frequency offset.