• 보존과학회지
• /
• 제31권2호
• /
• pp.125-130
• /
• 2015

전통 칠기의 보존처리에 있어 수리 복원 기술이나 재료 등에 관한 명확한 기록이나 전승이 제대로 이루어지지 않고 있다. 본 연구는 목칠기 보존처리 중 하지층 복원에 사용되는 충진제의 기초적인 특성을 비교하여 칠기 하지층 복원시 적합한 재료를 선택적으로 사용하는데 목표를 두고 있다. 토회와 3종의 첨가제를 혼합한 토회, 곡수를 사용하여 시료를 제작하여 건조속도, 색도, 내충격성, 연마도를 비교하였다. 건조 속도는 토회, 목분 혼합, 목탄분 혼합, 와분 혼합, 곡수, 맥칠 시료의 순이었으며, 상대적으로 토분의 비율이 많아질수록 건조속도는 빠르고, 표면의 균열이 심해졌다. 내충격성 또한 토분의 비율이 많아질수록 낮은 값을 보였다. 첨가제의 종류에 따른 차이는 크지 않았으며 곡수와 첨가제를 혼합한 시료 모두 상대적으로 높은 내충격성을 보였다. 연마도의 경우 토분의 양이 많아질수록 커지고, 목분과 목탄분을 혼합한 시료 역시 큰 연마도를 보였다. 맥칠과 곡수 시료는 가장 큰 연마도를 보였고 와분을 혼합한 시료의 경우 가장 낮은 연마도를 보였다.

• 한국철도학회논문집
• /
• 제18권6호
• /
• pp.578-585
• /
• 2015

궤도의 탄성 구성요소는 기술적 및 경제적으로 효율적인 철도 네트워크를 위해 궤도상부구조로 잘 통합될 수 있다. 탄성 레일패드는 곡선반경이 800m보다 큰 경우 부드러운 레일지점과 고속(160km/h 이상)을 제공한다. 높은 궤도저항성은 눈에 띄게 다짐주기를 연장시킨다. 침목패드의 꾸준히 증가된 점유율은 향상된 다짐주기와 연마주기를 제공하고, 좁은 곡선반경에서도 기술적인 철도구조물 그리고 고체음의 감소에 대한 대책을 제공하기 때문이다. 밸러스트 매트의 설치는 신설선 건설 또는 광범위한 혁신 조치의 차원에서 특히 방진 및 구조물 보호와 같은 좋은 효과를 준다. 다만, 적절한 설치에는 세심한 주의가 필요하다.

• Tribology and Lubricants
• /
• 제39권1호
• /
• pp.28-34
• /
• 2023

Because of their cleanliness, low friction, and high stiffness, aerostatic bearings are used in numerous applications. Aerostic bearings that use porous materials as means of flow restriction have higher stiffness than other types of bearings and have been successfully applied as guide bearings, which have high motion accuracy requirements. However, the performances of porous bearings exhibit strong nonlinearity and can vary considerably depending on design parameters. Therefore, accurate prediction of the performance characteristics of porous bearings is necessary or their successful application. This study presents a porous bearing design and performance analysis for a spindle used in wafer polishing. The Reynolds and Darcy flow equations are solved to calculate the pressures in the lubrication film and porous busing, respectively. To verify the validity of the proposed analytical model, the calculated pressure distribution in the designed bearing is compared with that derived from previous research. Additional parametric studies are performed to determine the optimal design parameters. Analytical results show that optimal design parameters that obtain the maximum stiffness can be derived. In addition, the results show that cross-coupled stiffness increases with rotating speed. Thus, issues related to stability should be investigated at the design stage.

• 한국전기전자재료학회논문지
• /
• 제36권3호
• /
• pp.214-225
• /
• 2023

Piezoelectric actuators, which utilize piezoelectric crystals or ceramics, are commonly used in precision positioning applications, offering high-speed response and precise control. However, the use of low-performance ceramics and expensive single crystals is limiting their versatile use in the actuator market, necessitating the development of both high-performance and cost-effective piezoelectric materials capable of delivering higher forces and displacements. The use of textured Pb (lead)-based piezoelectric ceramics formed by so-called templated grain growth method has been identified as a promising strategy to address the performance and cost issue. This review article provides insights into recent advances in texturing Pb-based piezoelectric ceramics for improved performance in actuation applications. We discussed the relevant issues in detail focusing on current challenges and emerging trends in the textured piezoelectric ceramics for their reliability and performance in actuator applications. We discussed in detail focusing on current challenges and emerging trends of textured piezoelectric ceramics for their reliability and performance in actuator applications. In conclusion, the article provides an outlook on the future direction of textured piezoelectric ceramics in actuator applications, highlighting the potential for further success in this field.

• 대한미생물학회지
• /
• 제7권1호
• /
• pp.21-27
• /
• 1972

생검(生檢)한 나결절(癩結節)에서 간단(簡單)하고 효과적(效果的)인 방법(方法)인 trypsin 처리(處理)와 고속도유침(高速度遠沈)에 의(依)하여 동물접종목적(動物接種目的)에 사용(使用)할수 있는 인나균(人癩菌)의 정제(精製)에 대(對)하여 기술(記述)하였다. 본(本) 방법(方法)의 한 특징(特徵)은 그 정제과정중(精製過程中)에 재래식(在來式)인 나결절조직(癩結節組織)의 마쇄(磨碎)나 유액화조작(乳液化操作)을 전혀 포함(包含)시키지 않은 점(點)이다. 이 방법(方法)에 의(依)하여 정제(精製)된 인나균(人癩菌)을 한국산(韓國産) 다람쥐(Tamias sibiricus asiaticus, Gmelin)의 족저부(足底部) 및 이타조직내(耳朶組織內)에 접종(接種)하였던 바 균접종(菌接種) 8 및 12개월(個月)에 이르러 균증식양상(菌增殖樣狀)이 야기(惹起)됨이 관찰(觀察)되었다.

• 한국재료학회지
• /
• 제20권11호
• /
• pp.559-569
• /
• 2010

The liquid-phase sintering method was used to prepare a glass lens forming core composed of SiC-$Al_2O_3-Y_2O_3$. Spark plasma sintering was used to obtain dense sintered bodies. The sintering characteristics of different SiC sources and compositions of additives were studied. Results revealed that, owing to its initial larger surface area, $\alpha$-SiC offers sinterability that is superior to that of $\beta$-SiC. A maximum density of $3.32\;g/cm^3$ (theoretical density [TD] of 99.7%) was obtained in $\alpha$-SiC-10 wt% ($6Al_2O_3-4Y_2O_3$) sintered at $1850^{\circ}C$ without high-energy ball milling. The maximum hardness and compression stress of the sintered body reached 2870 Hv and 1110 MPa, respectively. The optimum ultra-precision machining parameters were a grinding speed of 1243 m/min, work spindle rotation rate of 100 rpm, feed rate of 0.5 mm/min, and depth of cut of $0.2\;{\mu}m$. The surface roughnesses of the thus prepared final products were Ra = 4.3 nm and Rt = 55.3 nm for the aspheric lens forming core and Ra = 4.4 nm and Rt = 41.9 for the spherical lens forming core. These values were found to be sufficiently low, and the cores showed good compatibility between SiC and the diamond-like carbon (DLC) coating material. Thus, these glass lens forming cores have great potential for application in the lens industry.

• 한국정밀공학회지
• /
• 제28권9호
• /
• pp.1078-1085
• /
• 2011

Prediction of a minimum crack size for growth, which is defined as a crack size that grows fast enough to keep ahead of its removal by contact wear and periodic grinding, is the most demanding work to prevent rail from fatigue failure and develop cost effective railway maintenance strategy In this study, we investigated the wheel load increment due to a rail defect during a train ran over it, and its effect on the minimum crack size for growth. For this purpose, we developed simulation software based on the Fletcher and Kapoor's "2.5D" model and measured wheel load increment during a train passed over a defect. A maximum contact pressure and contact patch size were calculated by 3D FEM and crack growth analyses were performed by varying two of dominant contact contributors; surface friction coefficient(0.1, 0.2, 0.3 and 0.4) and crack aspect ratio. The minimum crack sizes for growth were calculated from 0.29 to 1.44mm depending on the contact conditions. They were decreasing with increasing surface friction coefficient and decreasing with crack aspect ratio(a/b).

• 한국재료학회지
• /
• 제26권3호
• /
• pp.136-142
• /
• 2016

To study the dispersion factors of silica sol prepared from fumed silica powder, we prepared silica sol under an aqueous system using a batch type bead mill. The dispersion properties of silica sol have a close relationship to dispersion factors such as pH, milling time and speed, the size and amount of zirconia beads, the solid content of fumed silica, and the shape and diameter of the milling impellers. Especially, the silica particles in silica sol were found to show dispersion stability on a pH value above 7, due to the electrostatic repulsion between the particles having a high zeta potential value. The shape and diameter of the impellers installed in the bead mill for the dispersion of fumed silica was very important in reducing the particle size of the aggregated silica. The median particle size ($D_{50}$) of silica sol obtained after milling was also optimized according to the variation of the size and amount of the zirconia beads that were used as the grinding medium, and according to the solid content of fumed silica. The dispersion properties of silica sol were investigated using zeta potential, turbiscan, particle size analyzer, and transmission electron microscopy.

• 한국항행학회논문지
• /
• 제26권4호
• /
• pp.235-243
• /
• 2022

본 논문에서는 관성 항법 시스템 (INS)의 경우, 수직편향 (DOV)으로 인한 초기정렬에서의 자세 추정 오차를 분석한다. INS의 속도 및 자세 오차를 기반으로 DOV로 인한 자세 추정 오차를 이론적으로 분석하였다. 이론적 분석을 검증하기 위한 시뮬레이션을 수행했으며 결과는 이론적 분석과 잘 일치했다. 일례로 η=20"일 경우 정렬오차는 ϕ_N=0.00287°, ϕ_U=0.00196°가발생하며, 𝜉=20"일 경우에는 ϕ_E= -0.00286°의 오차가 발생하였다. 이를 통해 INS 자세오차의 결합특성으로 DOV에 기인한 수직 자세오차가 발생함을 확인하였다. 기존의 INS 정렬에서는 고려하지 않았던 DOV로 인해 추가로 자세오차가 발생할 수 있음을 보여 주었으며 이는 고정밀 INS 적용시에 DOV에 대한 보정을 반드시 고려해야 함을 의미한다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 춘계학술대회 논문집
• /
• pp.23-28
• /
• 2002

This paper describes the machining characteristics of the $MoSi_2$ based composites by electric discharge drilling with various tubular electrodes, besides, Hardness characteristics and microstructures of $Nb/MoSi_2$ laminate composites were evaluated from the variation of fabricating conditions such as preparation temperature, applied pressure and pressure holding time. $MoSi_2$ -based composites has been developed in new materials for jet engine of supersonic-speed airplanes and gas turbine for high- temperature generator. Achieving this objective may require new hard materials with high strength and high temperature-resistance. However, With the exception of grinding, traditional machining methods are not applicable to these new materials. Electric discharge machining (EDM) is a thermal process that utilizes a spark discharge to melt a conductive material, the tool electrode being almost non-unloaded, because there is no direct contact between the tool electrode and the workpiece. By combining a nonconducting ceramics with more conducting ceramic it was possible to raise the electrical conductivity. From experimental results, it was found that the lamination from Nb sheet and $MoSi_2$ powder was an excellent strategy to improve hardness characteristics of monolithic $MoSi_2$. However, interfacial reaction products like (Nb, Mo)$SiO_2$ and $Nb_2Si_3$ formed at the interface of $Nb/MoSi_2$ and increased with fabricating temperature. $MoSi_2$ composites which a hole drilling was not possible by the conventional machining process, enhanced the capacity of ED-drilling by adding $NbSi_2$ relative to that of SiC or $ZrO_2$ reinforcements.