• Journal of Ocean Engineering and Technology
• /
• v.31 no.5
• /
• pp.335-339
• /
• 2017

This study investigated the sea trial performance of a wave piercing high speed planing hull (WPH). The bow shape of the boat is sharp, and it has no chine or spray strip like a normal planing boat. The skeg is attached to the bottom of the boat in the longitudinal direction from the bow to the stern. The speed performance was analyzed as the speed dropped in a wave, and the seakeeping performance was compared with that of a planing boat with a similar velocity coefficient by measuring the vertical acceleration of the bow in the wave. The turning circle was compared with Lewandowski's estimation for a planing boat. As a result of this study, it was confirmed that the velocity drop of the developed WPH was not large in a wave, and the vertical acceleration was greatly reduced compared with that of a normal planing boat. The turning circle was somewhat larger than the estimated results for a planing boat, but the overall tendency was the same.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.2
• /
• pp.182-188
• /
• 2012

The hull form design technique for high speed power boat based on the parametric design method is presented in this paper. While the design methods of conventional vessels that are currently in use have been well developed in various aspects from existing database. However, an easy and simple design program for high speed power boats needs to be provided for the relatively small boat builders who are in lack of experience and skilled manpower. This paper presents a parametric design technique which is aimed to provide an easier creation of a new model by inputting several parameters, such as angles and lengths, which correlate with hydrodynamics characteristic for high speed boats. The paper also introduces the prototype program developed to design power boat with parametric design technique.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.4
• /
• pp.84-89
• /
• 2008

It is hard to find experimental data for a model test of small high-speed planning boats. It is difficult to verify the performance seen in a model test for a high-speed boat because the ship-model scale-ratio is very small and the flow velocity of the circulating water channel and the X-carriage speed of the towing tank are restricted. Therefore most hull-form designs for high-speed small boats depend on the sea-trial test result for similar boats or evaluation through numerical calculations. This study investigated the anti-rolling effect of the stern sub-body in a 50-knot doss planning boat. To carry out this work, new model test procedures were set up in the actual sea. Using this method, the anti-rolling effect of the stern sub-body was investigated. A stern sub-body attached to a planning boat was proved to be effective in reducing the roll and pitch angle.

• Journal of Navigation and Port Research
• /
• v.34 no.8
• /
• pp.623-628
• /
• 2010

High speed marine vehicle, such as semi-planing, planing craft have been developed recently. These ships paid attention to the resistance characteristics, especially in high speed region. Model test method is divided to two equipment greatly, first 'Towing tank', second 'C.W.C.'. It is difficult to estimate a resistance characteristics for high speed boat. because these are made for low speed ship. This paper suggests a new model test method and system. This is real sea model test and it's comprised of eight part. Firstly, This method is tested at C.W.C that is possible to using in real sea model tes using low speed boat modelt. And then, Real sea model test and CFD calculation are performed and compared with tow way used high speed boat model. It can be a good way to estimate a performance for high speed boat.

• 한국기계연구소 소보
• /
• s.10
• /
• pp.63-77
• /
• 1983

This paper presents the hydrodynamic performance characteristics of a planing boat which was tested with a new dynamometer system specifically designed to measure towing force along the thrust plane, the change in trim angle and the vertical displacement of the model center of gravity from still water condition. The test conditions include systematic variations in the three positions of LCG and the three load coefficients of a high speed planing boat.

• Journal of Ship and Ocean Technology
• /
• v.9 no.2
• /
• pp.1-10
• /
• 2005

A light-weight cantilever type towing carriage was devised and installed in the towing tank at Seoul National University. Wireless measurement devices were also provided for appropriate data acquisition during high-speed towing tests. With the new carriage system, a series of model tests were performed to investigate the hydrodynamic characteristics of the racing boat in the towing tank and the resistance test results had sufficient accuracy so that they could be used in the development of a high speed planning hull.

• Journal of Navigation and Port Research
• /
• v.42 no.3
• /
• pp.177-186
• /
• 2018

Designers need a lot of information to determine the principal dimensions in the initial stage of boat design, and most of the information they need can be obtained by investigating and analyzing similar existing boat data. In addition, the principal dimensions that are determined have an impact throughout the design process (basic/detailed design), which in turn leads directly to the stability and performance of the boat. Therefore, in this study, the initial design system for the boat (design support platform) was developed using a correlation analysis with existing data for more than 700 boats. It was confirmed that the designer could conveniently and reasonably derive and determine the principal dimensions for a boat in the initial design stage, for the 50ft-class of small and high-speed boats.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.2
• /
• pp.69-74
• /
• 2016

A new wave-piercing-type high-speed planing boat without a chine was developed, and its basic performance was investigated in a model test, including the resistance, trim, and sinkage. The maximum speed of the developed ship was 35 knots. The hull form was developed by combining a VSV (very slender vessel) and TH (transonic hull), which have large deadrise angles at the bow. The main dimensions were estimated by a statistical approach using actual ship data. The effect of a side fin attached at the stern near the water line was investigated from a resistance point of view. It was found that the developed hull form showed the possibility of a new concept for a high-speed planing hull without a chine, and the side fin played an important role in increasing the resistance performance by controlling the trim and sinkage in the high-speed range.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.6
• /
• pp.784-789
• /
• 2015

It was carried out a review of operating limit analysis for small high-speed boat by author. In general, a review of ship's seakeeping performance is performed in the step of ship design, but this study was carried out in the state of completion of boat. Motion performance of Pitch, Vertical and Lateral acceleration and Slamming were satisfied in some encounter angle but deck wetness was not satisfied in all it does the analysis. As a result, sea state rather than the speed and encounter angle of vessel have a greater effect on the seakeeping performance of target vessel. It seems to be due to the size of the target ship.

• Proceedings of the KWS Conference
• /
• v.43
• /
• pp.213-215
• /
• 2004

Water jet propulsion system has high efficiency on middle to high speed, and it provides better safety than conventional screw propeller because it has not projected propeller and rudder. So many leisure boat and high-speed ferries use this propulsion system. We developed water-jet propulsion unit for small planning boat, and launched that in the boat, after that we tested water-jet unit in the lake. As a result, we certify heat dissipation at the bearing housing and reverse duct's shape for neutral position are important at the design, and alignment water-jet unit and keel line are important at the launching, and ship's resistance performance and jet's propulsion performance also are needed to consideration.