• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.976-978
• /
• 1999

Recently PWM invertor is broadly used for control of induction motor. The invertor is able to generate sin wave current from high speed switching power device such as IGBT. However the invertor is disturbed by dead time inevitably needed to prevent a short of the DC link voltage, and the dead time mainly causes distortions of the output current. In this Paper the dead time compensation method which corrects the voltage error from dead time, and Min Max algorithm enlarging the operating voltage of PWM were Proposed. This method can be implemented by software programming without any additional hardware circuit. The proposed algorithms were implemented by DSP(TMS320C31, 40MHz) and FPGA(QL2007, Quick Logic) described in VHDL. and applied to 3 phase induction motor(2.2 KW) to show the superior performance

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.1
• /
• pp.58-69
• /
• 2016

This paper describes the design and implementation of a new diode clamped multilevel inverter for variable frequency drive. The diode clamp multilevel inverter has been widely used for low power, high voltage applications due to its superior performance. However, it has some limitations such as increased number of switching devices and complex PWM control. In this paper, a new topology is proposed. New topology requires only (N-1) switching devices and (N-3) clamping diodes compared to existing topology. A modified APO-PWM control method is used to generate gate pulses for inverter. The proposed inverter topology is coupled with single phase induction motor and its performance is tested by MATLAB simulation. Finally, a prototype model has built and its performance is tested with single phase variable frequency drive.

• Proceedings of the KIEE Conference
• /
• 1990.07a
• /
• pp.430-432
• /
• 1990

This paper concerns a method for high precision torque control of induction motor supplied with power via a Transister inverter. The control system is totaly digitized using DSP - TMS32010.Since operation time leads to control delay in such a system, torque ripples are more significient than relieved considerably by using current preview control and vector pulse width control. The usefulness of these techniques will be demonstrated by showing the results of a simulation,and results of measurement on a 2.2Kw induction motor.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.5 no.4
• /
• pp.352-357
• /
• 2000

The vector control scheme is usually applied to the high performance induction motor drives. The PI controller is adopted traditionally to control the motor speed and currents in the vector control scheme. In this case, the dynamic performance of the induction motor is dependent on the PI gains and the gain optimization is necessary in order to get a good dynamic performance. But, it is very hard to optimize the PI gains uniquely within the speed control range because the equivalent model of the motor control system should be known exactly. In this paper, we propose the hybrid control scheme to remove the defects of PI controller. The hybrid control scheme includes the simplified fuzzy controller which operates in the transient state and the PI controller which operates in the steady state. The proposed scheme is applied to the vector control for induction motor, and the digital simulation and the experimental results are given to verify the proposed scheme.

• Journal of Power System Engineering
• /
• v.9 no.2
• /
• pp.45-49
• /
• 2005

Liquefied natural gas takes up six hundredths of the volume of natural gas, which makes storage and transportation much easier. To send out natural gas via a pipeline network across the nation, high-pressure LNG pumps supply highly compressed LNG to high-pressure vaporization facilities. The Number of high-pressure LNG pumps determined the send-out amount in LNG receiving terminal. So it is main equipment at LNG production process and should be maintained on best conditions. In this paper, to find out the cause of high beat vibration at cryogenic pumps, vibration and motor current signal analysis have been performed. High vibration of cryogenic pumps could be reduced due to the modification of motor rotor.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.270-272
• /
• 2004

At the water supply field, high voltage induction motor is main facility of a load equipment. The motor is often out of order and its noise, generated heat, loss etc occurred occasionally. especially, transmission motor for flux control generates an amount of the harmonics then have a bad influence upon the electric power system. In this study, to analyze the total harmonics distortion of the water supply field receiving high voltage, the harmonics measured and analyzed using the PQA(Power quality Analyzer) according to the electric power system and electrical load and the reduction method presented.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.2077-2078
• /
• 2011

Now a days, the induction motor is widely used in industry automation. Without monitoring the motor fault, maintenance cost is increased undesirably high. The slip frequency is included in the feature frequency, so rotating rotor speed is needed. In this paper, a sensorless motor speed estimation method, rotor slot harmonic(RSH) method is suggested and a solution of rotor bar diagnosis is proposed for motor running with light-load. When the rotor is rotating, it shows the harmonic signal of back-emf voltage related with number of rotor slot. So from the power spectrum of current signal, we can find the rotor speed.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.699-702
• /
• 1992

A miniature size electrostatic induction motor have been constructed and studied by applying a three phase ac power source with a maximum voltage of 5 KV and a variable frequency ranged 0.0 - 150 Hz. A maximum no load speed of the motor tested was about 7600 RPM at the applied voltage of 4330 volt and the frequency of 130 Hz for the case of the rotor surface material of polyprophylene sheet screen-printed $TiO_2$ powder on it. It is found that there are 3 different regions of the motor operation, a rotor stop region, a stable operation region and a high speed abnormal region. And it is also found that the motor speed is influenced greatly by the charge relaxation time constant of the rotor surface materials, which however was changed by the means of vapour-deposited Ti or Ni and screen-printed $TiO_2$ powder on the surface of the rotor material, polyprophylene.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.4
• /
• pp.364-371
• /
• 2004

This thesis is proposing novel RPWM(Random PWM) techniques that can locate PWM pulse to do random. RPWM techniques to propose locates SVPWM(Space Vector PWM) pulse by number of each random and principle to locate of pulse applies different random function and locate pulse. For propriety verification of proposed techniques, achieve an simulation and experiment that use MATLAB/SIMULINK about proposed RPWM techniques algorithm and IGBT inverter composition that use DSP(TMS320C31). Specially, analyze harmonic spectra of inverter output current when the induction motor speed is more than 10,000 rpm, confirm that RPWM's effect in high speed degree appears. Proposed RPWM techniques propriety prove from reduction effect of harmonic magnitude that corresponds to an integer times of switching frequency.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1197-1199
• /
• 2001

TFM(Transeverse Flux Motor) is switched reluctance motor with new structure of novel design concept based on the high efficiency and power density compare to induction motor used on wide industrial field. This paper realized FWM asymmetric converter drive control system for TFM using IGBT and DSP.