• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.269-270
• /
• 2019

Vienna rectifier is used for telecom power applications because of its simple structure, high efficiency and high power density. This rectifier is also suitable to obtain a high voltage DC output. This paper describes the analysis and design of a single-phase module of a Vienna rectifier to obtain 750VDC output. The simulation and experimental results are provided to verify the theoretic analysis and design.

• Journal of Power Electronics
• /
• v.12 no.3
• /
• pp.458-467
• /
• 2012

Single phase converters suffer from ripple power pulsating at twice the line frequency. The ripple power is usually absorbed by a bulky capacitor bank and/or a dedicative LC resonant link, resulting in a low power density and a high cost. An alternative solution is using a dc link active power filter (APF) to direct the pulsating power into another energy-storage component. The main dc link filter capacitor can then be reduced substantially. Based on a mainstream dc APF topology, this paper proposed a new control strategy incorporating both dual-loop control and repetitive control. The circuit parameter design is also re-examined from a control point of view. The proposed APF scheme has better control performance, and is more suited for high power applications since it works in CCM and with a low switching frequency.

• Journal of Power Electronics
• /
• v.18 no.4
• /
• pp.975-984
• /
• 2018

This work presents a high efficiency phase shifted full bridge (PSFB) DC-DC converter for use in the second stage of a battery charger for neighborhood electrical vehicle (EV) applications. In the design of the converter, Lithium-ion battery cells are preferred due to their high voltage and current rates, which provide a high power density. This requires wide range output voltage regulation for PSFB converter operation. In addition, the battery charger works with a light load when the battery charge voltage reaches its maximum value. The soft switching of the PSFB converter depends on the dead time optimization and load condition. As a result, the converter has to work with soft switching at a wide range output voltage and under light conditions to reach high efficiency. The operation principles of the PSFB converter for the continuous current mode (CCM) and the discontinuous current mode (DCM) are defined. The performance of the PSFB converter is analyzed in detail based on wide range output voltage and load conditions in terms of high efficiency. In order to validate performance analysis, a prototype is built with 42-54 V / 15 A output values at a 200 kHz switching frequency. The measured maximum efficiency values are obtained as 94.4% and 76.6% at full and at 2% load conditions, respectively.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.249-252
• /
• 2000

A new Smart rower IC's based on the Partial SOI technology was designed for such applications as mobile communication systems, high-speed HDD systems etc. A new methodology of integrating a 0.8${\mu}{\textrm}{m}$ BiCMOS compatible Smart Power technology, high voltage bipolar device, high speed SAVEN bipolar device, LDD NMOSFET and a new LDMOSFET based on the Partial SOI technology is presented in this paper. The high voltage bipolar device has a breakdown voltage of 40V for the output stage of analog circuit. The optimized Partial SOI LDMOSFET has an off-state breakdown voltage of 75 V and a specific on- resistance of 0.249mΩ.$\textrm{cm}^2$ with the drift region length of 3.5${\mu}{\textrm}{m}$. The high-speed SAVEN bipolar device shows cut-off frequency of about 21㎓. The simulator DIOS and DESSIS has been used to get these results.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.5
• /
• pp.563-569
• /
• 2015

For some low-frequency applications such as power-related circuits, NEM relays have been known to show better performance than MOSFETs. For example, in a step-down charge pump circuit, the NEM relays showed much smaller layout area and better energy efficiency than MOSFETs. However, severe process variations of NEM relays hinder them from being widely used in various low-frequency applications. To mitigate the process-variation problems of NEM relays, in this paper, a new NEM-relay charge pump circuit with the self-adjustment is proposed. By self-adjusting a pulse amplitude voltage according to process variations, the power consumption can be saved by 4.6%, compared to the conventional scheme without the self-adjustment. This power saving can also be helpful in improving the power efficiency of the proposed scheme. From the circuit simulation of NEM-relay charge pump circuit, the efficiency of the proposed scheme is improved better by 4.1% than the conventional.

• Journal of Advanced Navigation Technology
• /
• v.9 no.2
• /
• pp.164-169
• /
• 2005

In this paper, the high efficiency Doherty power amplifier using adaptive bias technique has been designed and realized for 2.3GHz Wibro applications. The RF performances of the Doherty power amplifier using adaptive bias technique have been compared with those of a class AB amplifier alone, and conventional Doherty amplifier. The Maximum PAE of designed Doherty power amplifier with adaptive bias technique has been 36.6% at 34.0dBm output power. The proposed Doherty power amplifier showed an improvement 1dB at output power and 7.6% PAE than a class AB amplifier alone.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.1
• /
• pp.1-8
• /
• 2022

Recently, photovoltaic (PV) systems have been gradually applied in eco-friendly vehicle applications to improve fuel economy. The relevant market is expected to continue to grow because the installation of large-capacity PV systems to other eco-friendly vehicles, such as electric buses and trains, is being considered. However, in a PV system, power imbalance between submodules and low power generation efficiency occur due to factors such as cell aging, contamination, and shading. To resolve this problem, various differential power processing (DPP) converters have been researched and developed. However, conventional DPP converters suffer from large volume and low efficiency. Therefore, to apply DPP converters to eco-friendly vehicles, increasing efficiency and reducing volume and price compared with existing DPP converters is necessary. In this paper, a novel DPP converter with an integrated transformer is proposed and analyzed. The proposed DPP converter uses a single magnetic component by integrating transformers and secondary sides of conventional DPP converters. Therefore, the proposed DPP converter shows high power density and high efficiency, and it is suitable for PV systems in eco-friendly vehicle applications.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.920-927
• /
• 1998

This paper proposed that an Analysis of a partial resonant AC-DC converter for high power and power factor operates with four choppers connecting to a number of parallel circuit. To improve these, a large number of soft switching topologies included a resonant circuit have been proposed. And, some simulative results on computer are included to confirm the validity of the analytical results. The partial resonant circuit makes use of an inductor using step-down and a condenser of lose-less snubber. The result is that the switching loss is very low and the efficiency of system is high. And the snubber condenser used in a partial resonant circuit makes charging energy regenerated at input power source for resonant operation. The proposed conversion system is deemed the most suitable for high power applications where the power switching devices are used

• Journal of Power Electronics
• /
• v.3 no.2
• /
• pp.81-89
• /
• 2003

The global electrical energy consumption is still rising and there is a steady demand to increase the power capacity, to produce, distribute and use the energy as0 efficient as possible and furthermore to set up incentives to save energy at the md-user. Two major technologies will play important roles to fulfill those targets. One is to change the electrical power production sources from the conventional, fossil (and short term) based energy sources to renewable energy resources. The other is to use high efficiency power electronics in power systems for high efficiency and high performance applications. This paper discusses both areas, in particular the power electronic application in wind power integration.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.24-24
• /
• 2003

Research activity in the III-V nitrides materials system has increased markedly in the past several years ever since high-brightness blue light-emitting diodes (LEDs) became commercially available. Despite of excellent optical properties of the GaN, however, inherently poor thermal property of the sapphire used as a substrate material n these devices may lead to thermal degradation of devices, especially during their high power operation. Therefore, dependable thermal analysis and packaging schemes of GaN-based LEDs are necessary for solid lighting applications under high power operation. In this paper, emphasis will be placed upon thermal design of GaN-based LEDs. Thermal measurements of LEDs on chip and packaging scale were performed using the liquid crystal thermographic technology and micro thermocouples for different bias conditions. By a series of optical arrangement, hot spots with specific transition temperatures were obtained with increasing input power. Thermal design of LEDS was made using the finite element method and analytical unit temperature profile approach with optimal boundary conditions. The experimental results were compared to the simulated data and the results agree well enough for the establishment of dependable prediction of thermal behavior in these devices. The paper will present a more detailed understanding of the thermal analysis of the GaN-based blue and white LEDs for high power applications.