• 한국지진공학회논문집
• /
• 제10권2호
• /
• pp.11-19
• /
• 2006

본 연구에서는 4층, 10층, 30층 스태거드 트러스 시스템 (STS)의 비탄성 정적해석에 의한 하중-변위 관계와 비탄성거동을 분석하고, 그 결과를 바탕으로 STS의 내진성능을 평가하였다. 또한 동일한 규모의 모멘트골조 및 가새골조의 거동과 비교함으로써 STS의 횡력 저항 능력을 파악하였다. 해석결과에 따르면, STS는 일반적으로 적용되는 구조시스템에 비하여 비교적 만족할 만한 내진성능을 보유하는 것으로 나타났다. 그러나 중층 이상의 STS에 있어서는 상대적으로 강성이 작은 비렌딜 패널 상.하현재에 소성변형이 발생한 후 인접한 수직 가새가 항복함으로써, 다른 층으로 소성변형이 전이되지 못하여 약층의 형성에 의한 취성적인 거동을 보인다. 그러므로 스태거드 트러스 시스템의 연성능력을 확보하기 위해서는 비렌딜 패널의 수직 가새를 보강하여 비렌딜 패널 상하현재에 발생한 소성변형을 다른 층의 비렌틸 패널로 유도하는 것이 필요하다.

• 한국강구조학회 논문집
• /
• 제23권3호
• /
• pp.385-395
• /
• 2011

교량용 HSB 고성능 강재를 적용한 정모멘트부 강합성 복합단면 거더의 휨저항강도를 모멘트-곡률 해석법으로 산정하고 LRFD 휨저항강도 설계식에 의한 휨저항강도와 비교하여 기존 설계식의 적용성을 검토하였다. 강거더의 하부플랜지는 HSB800 강재를 상부플랜지와 복부판은 HSB600 강재를 적용하였다. 다양한 연성특성을 갖는 6,205개 단면을 임의추출법으로 선정하고 재료 비선형 모멘트-곡률 해석 프로그램을 이용하여 이들 단면에 대한 휨저항강도를 구하였다. 합성단면을 구성하는 콘크리트 재료는 CEB-FIP 모델로, HSB600 및 HSB800 강재는 탄소성-변형경화 재료로 모델링하였으며 콘크리트 바닥판의 압축강도는 30MPa, 45MPa 및 60MPa를 고려하였다. HSB 강재를 적용한 강합성 복합단면 거더의 연성계수와 콘크리트 바닥판의 압축강도에 따른 휨저항강도 특성을 분석하였다. HSB 고성능강을 적용한 이종 복합단면 강합성 거더의 모멘트-곡률해석 결과, 현 AASHTO LRFD 정모멘트부 휨저항강도 산정식을 적용할 수 있는 것으로 평가되었다.

• 콘크리트학회논문집
• /
• 제19권3호
• /
• pp.313-322
• /
• 2007

PCS 구조 시스템은 프리캐스트 콘크리트 기둥과 철골보로 이루어진 합성 구조 시스템의 일종이다. 이 시스템은 접합부를 볼트로 연결함으로써 완전건식공법이며 조립식이어서 시공성 및 경제성 면에서 많은 장점을 가지고 있다. 본 연구에서는 실험체를 구성하는 PC 기둥 및 접합부를 개발하였으며, PCS 구조 시스템의 구조적 특성과 내진 성능을 파악하기 위하여 다양한 실험을 수행하였다. 실험 결과 개발된 PC 기둥은 손상 이후에도 강도 성능을 유지하는 우수함을 보였다. 철골보의 스캘럽은 파괴 모드 조절 및 에너지소산 능력에 효율적인 것으로 나타났으며, 단부 평판으로 구속된 접합부는 그 강도 성능이 매우 우수하였다 타설된 슬래브는 파괴 모드 조절 및 에너지소산 능력에 바람직하지 못한 효과를 보였다. 내진 성능 분석 결과 PCS 구조 시스템은 초기 강성을 제외한 강도 및 강성 저하, 에너지소산 성능의 ACI 기준을 모두 만족하는 것으로 나타났으며 매우 우수한 것으로 분석되었다. 초기 강성의 경우 PCS 구조 시스템은 다른 합성 구조와 비슷한 수준이었으며, 일반콘크리트 및 철골조도 ACI의 기준을 만족하지 못하는 것으로 조사되었다. 이러한 이유는 ACI의 초기 강성 평가 기준이 부분 구조 실험체만으로는 만족하는데 한계가 있기 때문이다. 그러므로 본 연구에서 수행된 PCS 구조 시스템은 내진 성능 및 역학적 성능이 매우 우수한 것으로 판단된다.

• 대한기계학회논문집A
• /
• 제24권3호
• /
• pp.777-785
• /
• 2000

The low-cycle fatigue behaviors of cast AI-Si alloy and composite with reinforcement of SIC particles were compared with those of extruded unreinforced matrix alloy and composite in order to investigate the influence of cast and extrusion processes on the cyclic deformation and fatigue life. Generally, both cast and extruded composites including the unreinforced alloy exhibited cyclic hardening behaviour, with more pronounced strain-hardening for the composites with a higher volume fraction of the SiC particles. However, cast composite under a low applied cyclic strain showing no observable plastic strain exhibited cyclic softening behavior due to the cast porosities. The elastic modulus and yield strength of the cast composite were found to be quite comparable to those of the extruded composite, however, the extrusion process considerably improved the ductility and fracture strength of the composite by effectively eliminating the cast porosities. Low-cycle fatigue lives of the cast alloy and composite were shorter than those of the extruded counterparts. Large difference in life between cast and extruded composites was attributed to the higher influence of the cast porosities on the fatigue life of the composite than that of the unreinforced alloy material. A fatigue damage parameter using strain energy density effectively represented the inferior life in the low-cycle regime and superior life in the high-cycle regime for the composite, compared to the unreinforced alloy.

• 동력기계공학회지
• /
• 제3권2호
• /
• pp.51-56
• /
• 1999

Fatigue crack propagation rates and characteristics of the SA516-70 steel which is used for the low temperature pressure vessels, were studied in the room temperature of $10^{\circ}C$ and low temperature ranges of $-10^{\circ}C,\;-30^{\circ}C,\;-50^{\circ}C,\;and\;-70^{\circ}C$ with stress ratio of R=0.05. The obtained experimental results are as follows; 1) In the logarithmic relationship between the fatigue crack propagation rate(da/dN) and stress intensity factor K, the linear relationship was obtained up to da/dN > $8{\times}10^3$ mm/cycle in the same of room temperature, but in low temperature case, the relationship was extended to the range of low crack propagation rate. 2) The lower limit stress intensity factor of SA516-70 ${\Delta}K_{th}\;was\;23MPa\sqrt{m}$ and in the case of low temperature $-50^{\circ}C\;and\;-70^{\circ}C$, the crack propagation rate da/dN which showed a linear relation, reached rapidly to the ${\Delta}K_{th}$. As the results, the crack propagation rates of $-50^{\circ}C\;and\;-70^{\circ}C$ were lower than that of room temperature and according to the testing temperature the rates were decreased rapidly to the ${\Delta}K_{th}$. 3) On the relationship between the stress intensity factor ${\Delta}K$ and the track propagation cycle, the stress intensity factors of low cycle region was rapidly increased at low temperature, but ${\Delta}K$ was increased rapidly at room temperature of high cycle. 4) On the relationship between the fatigue crack propagation rate and cycle, the fatigue crack propagation rate showed higher gradient in the room temperature than the low temperature due to the increment in ductility at low temperature.

• Steel and Composite Structures
• /
• 제21권3호
• /
• pp.537-551
• /
• 2016

A new type of composite beam which consists of a wide flange steel shape beam and an innovative type of composite slab was introduced. The composite slab is composed of concrete slab and normal flat steel plates, which are connected by perfobond shear connectors (PBL shear connectors). This paper describes experiments of two large-scale specimens of that composite beam. Both specimens were loaded at two symmetric points for 4-point loading status, and mechanical behaviors under hogging and sagging bending moments were investigated respectively. During the experiments, the crack patterns, failure modes, failure mechanism and ultimate bending capacity of composite beam specimens were investigated, and the strains of concrete and flat steel plate as well as steel shapes were measured and recorded. As shown from the experimental results, composite actions were fully developed between the steel shape and the composite slab, this new type of composite beams was found to have good mechanical performance both under hogging and sagging bending moment with high bending capacity, substantial flexure rigidity and good ductility. It was further shown that the plane-section assumption was verified. Moreover, a design procedure including calculation methods of bending capacity of this new type of composite beam was studied and proposed based on the experimental results, and the calculation methods based on the plane-section assumption and plastic theories were also verified by comparisons of the calculated results and experimental results, which were agreed with each other.

• Steel and Composite Structures
• /
• 제33권6호
• /
• pp.793-803
• /
• 2019

Concrete-filled steel tubular (CFST) beam-columns are widely used owing to their good performance. They have high strength, ductility, large energy absorption capacity and low costs. Externally stiffened CFST beam-columns are not used widely due to insufficient design equations that consider all parameters affecting their behavior. Therefore, effect of various parameters (global, local slenderness ratio and adding hoop stiffeners) on the behavior of CFST columns is studied. An experimental study that includes twenty seven specimens is conducted to determine the effect of those parameters. Load capacities, vertical deflections, vertical strains and horizontal strains are all recorded for every specimen. Ratio between outer diameter (D) of pipes and thickness (t) is chosen to avoid local buckling according to different limits set by codes for the maximum D/t ratio. The study includes two loading methods on composite sections: steel only and steel with concrete. The case of loading on steel only, occurs in the connection zone, while the other load case occurs in steel beam connecting externally with the steel column wall. Two failure mechanisms of CFST columns are observed: yielding and global buckling. At early loading stages, steel wall in composite specimens dilated more than concrete so no full bond was achieved which weakened strength and stiffness of specimens. Adding stiffeners to the specimens increases the ultimate load by up to 25% due to redistribution of stresses between stiffener and steel column wall. Finally, design equations previously prepared are verified and found to be only applicable for medium and long columns.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 추계학술대회 논문집
• /
• pp.240-245
• /
• 2000

Fatigue crack propagation rates and characteristics of the SA516-60 steel which is used for the low temperature pressure vessels, were studied in the room temperature of $25^{\circ}C$ and low temperature ranges of $10^{\circ}C,\; -10^{\circ}C,\; -30^{\circ}C,\; -50^{\circ}C, \;and\; -70^{\circ}C4 with stress ratio of R=0.05. The obtained experimental results are as follows; 1) In the logarithmic relationship between the fatigue crack propagation rate(da/dN) and stress intensity factor K, the linear relationship was obtained up to da/dN 〉$8\times10^{-3}$/mm/cycle in the same of room temperature, but in low temperature case, the relationship was extended to the range of crack propagation rate. 2) The lower limit stress intensity factor of SA516-60 $\DeltaK_{th}$ was 15.8MPa and in the case of low temperature $-50^{\circ}C\; and\; -70^{\circ}C$, the crack propagation rate da/dN which showed a linear relation, reached rapidly to the $\DeltaK_{th}$/. As the results, the crack propagation rates of $-50^{\circ}C\; and\; -70^{\circ}C$ were lower than that of room temperature and according to the testing temperature the rates were decreased rapidly to the $\DeltaK_{th}$/. 3) On the relationship between the stress intensity factor $\DeltaK$ and the crack propagation cycle, the stress intensity factors of low cycle region was rapidly increased at low temperature, but $\DeltaK$ was increased rapidly at room temperature of high cycle. 4) On the relationship between the fatigue crack propagation rate and cycle, the fatigue crack propagation rate showed higher gradient in the room temperature than the low temperature due to the increment in ductility at low temperature.

• Steel and Composite Structures
• /
• 제37권1호
• /
• pp.91-98
• /
• 2020

Steel plate shear walls are recently used as efficient seismic lateral resisting systems. These lateral resistant structures are implemented to provide more strength, stiffness and ductility in limited space areas. In this study, the seismic behavior of the multi-story steel frames with steel plate shear walls are investigated for buildings with 4, 8, 12 and 16 stories using verified computational modeling platforms. Different number of steel moment bays with distinctive lengths are investigated to effectively determine the deflection amplification factor for low-rise and high-rise structures. Results showed that the dissipated energy in moment frames with steel plates are significantly related to the inside panel. It is shown that more than 50% of the dissipated energy under various ground motions is dissipated by the panel itself, and increasing the steel plate length leads to higher energy dissipation capability. The deflection amplification factor is studied in details for various verified parametric cases, and it is concluded that for a typical multi-story moment frame with steel plate shear walls, the amplification factor is 4.93 which is less than the recommended conservative values in the design codes. It is shown that the deflection amplification factor decreases if the height of the building increases, for which the frames with more than six stories would have less recommended deflection amplification factor. In addition, increasing the number of bays or decreasing the steel plate shear wall length leads to a reduction of the deflection amplification factor.

• Steel and Composite Structures
• /
• 제26권6호
• /
• pp.719-731
• /
• 2018

Concrete filled steel tubular (CFST) laced columns have been widely used in high rise buildings in China. Compared to solid-web columns, this type of columns has a larger cross-section with less weight. In this paper, four concrete filled steel tubular laced columns consisting of 4 main steel-concrete tubes were tested under cyclic loading. Hysteresis and failure mechanisms were studied based on the results from the lateral cyclic loading tests. The influence of each design parameter on restoring forces was investigated, including axial compression ratio, slenderness ratio, and the size of lacing tubes. The test results show that all specimens fail in compression-bending-shear and/or compression-bending mode. Overall, the hysteresis curves appear in a full bow shape, indicating that the laced columns have a good seismic performance. The bearing capacity of the columns decreases with the increasing slenderness ratio, while increases with an increasing axial compression ratio. For the columns with a smaller axial compression ratio (< 0.3), their ductility is increased. Furthermore, with the increasing slenderness ratio, the yield displacement increases, the bending failure characteristic is more obvious, and the hysteretic loops become stouter. The results obtained from the numerical analyses were compared with the experimental results. It was found that the numerical analysis results agree well with the experimental results.