• 한국건설순환자원학회논문집
• /
• 제2권4호
• /
• pp.354-359
• /
• 2014

이 연구의 목적은 혼화재 다량 치환 경량 및 보통중량 콘크리트의 압축 피로 특성 평가이다. 사용된 결합재는 시멘트 30%, 플라이애쉬 20%, 고로슬래그 50%이다. 콘크리트의 설계 압축강도는 40MPa 이다. 반복하중은 최대 응력비가 정적 콘크리트 압축강도의 75%, 80% 및 90%와 최소 응력비가 정적 강도의 10% 범위에서 1Hz의 속도로 가력하였다. 실험결과 혼화재 다량 치환 경량콘크리트의 피로수명은 혼화재 다량치환 보통중량 콘크리트에 비해 다소 낮았다. 최대응력에서의 피로변형률 값은 피로수명의 약 90% 이후부터 정정 응력-변형률 곡선의 하강부와 교차하였다.

• Computers and Concrete
• /
• 제22권2호
• /
• pp.183-196
• /
• 2018

The rheological behaviour of high strength self compacting concrete (HS-SCC) studied through an experimental investigation is presented in this paper. The effect of variation in supplementary cementitious materials (SCM) $vis-{\grave{a}}-vis$ four different types of processed crushed sand as fine aggregates is studied. Apart from the ordinary Portland cement (OPC), the SCMs such as fly ash (FA), ground granulated blast furnace slag (GGBS) ultrafine slag (UFS) and micro-silica (MS) are used in different percentages keeping the mix -paste volume and flow of concrete, constant. The combinations of rheology, strength and durability are equally important for selection of mixes in respect of high-rise building constructions. These combinations are referred to as the rheo-strength and rheo-durability which is scientifically linked to performance based rating. The findings show that the fineness of the sands and types of SCM affects the rheo-strength and rheo-durability performance of HS-SCC. The high amount of fines often seen in fine aggregates contributes to the higher yield stress. Further, the mixes with processed sand is found to offer better rheology as compared to that of mixes made using unwashed crushed sand, washed plaster sand, washed fine natural sand. The micro silica and ultra-fine slag conjunction with washed crushed sand can be a good solution for high rise construction in terms of rheo-strength and rheo-durability performance.

• 소성∙가공
• /
• 제10권1호
• /
• pp.35-41
• /
• 2001

The high temperature deformation behavior of SCM 440 can be characterized by the hot torsion test in the temperature ranges of $900^{\circ}C$~$1100^{\circ}C$ and strain rate ranges of 0.05/sec~5/sec. The aim of this paper is to establish the quantitative equation of the volume fraction of dynamic recrystallization (DRX) as a function of processing variables, such as strain rate ($\varepsilon$), temperature (T), and strain ('$\varepsilon$). During hot deformation, the evolution of microstructure could be analyzed from work hardening rate ($\theta$). For the exact prediction of dynamic softening mechanism the critical strain ($\varepsilon_c$), the strain for maximum softening rate ($\varepsilon^*$ and Avrami' exponent (m') were quantitatively expressed by dimensionless parameter, Z/A, respectively. The transformation-effective strain-temperature curve for DRX could be composed. It was found that the calculated results were agreed with the experimental data for the steel at any deformation conditions.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.5-21
• /
• 2006

Traditional standards and specifications for concrete have largely been prescriptive, (or prescription-based), and can sometimes hinder innovation and in particular the use of more environmentally friendly concretes by requiring minimum cement contents and SCM replacement levels. In December 2004, the Canadian CSA A23.1-04 standard was issued which made provisions (a) for high-volume SCM concretes, (b) added new performance requirements for concrete, and (c) clearly outlined the requirements and responsibilities for use in performance-based concrete specifications. Also, in December 2003, the CSA A3000 Hydraulic Cement standard was revised. It (a) reclassified the types of cements based on performance requirements, with both Portland and blended cements meeting the same physical requirements, (b) allows the use of performance testing for assessing sulphate resistance of cementitious materials combinations, (c) includes an Annex D, which allows performance testing of new or non-traditional supplementary cementing materials. From a review of international concrete standards, it was found that one of the main concerns with performance specifications has been the lack of tests, or lack of confidence in existing tests, for judging all relevant performance concerns. Of currently used or available test methods for both fresh, hardened physical, and durability properties, it was found that although there may be no ideal testing solutions, there are a number of practical and useful tests available. Some of these were adopted in CSA A23.1-04, and it is likely that new performance tests will be added in future revisions. Other concerns with performance standards are the different perspectives on the point of testing for performance. Some concrete suppliers may prefer processes for both pre-qualifying the plant, and specific mixtures, followed only with testing only 'end-of-chute' fresh properties on-site. However, owners want to know the in-place performance of the concrete, especially with high-volume SCM concretes where placing and curing are important. Also, the contractor must be aware of, and share the responsibility for handling, constructability, curing, and scheduling issues that influence the in-place concrete properties.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 춘계 학술논문 발표대회
• /
• pp.126-127
• /
• 2016

In this research, the optimum combination of fly ash (FA) and blast furnace slag (BS) was deduced by analyzing the performance of high volume supplementary cementitious materials (SCMs) cement mortar depending on various combinations of cement, FA, and BS. As a result, increased workability was shown with increased the portion of FA, while air content, setting time, and compressive strength were decreased.

• 산업공학
• /
• 제18권3호
• /
• pp.234-246
• /
• 2005

A silicon wafer is a highly customized product made to the individual order varying its electrical and physical characteristics. Therefore, it has distinctive supply chain structure that is different from highly standardized commodity product. For high-volume/high-standardization product, it is general that a main stream of information flow initiated by the production planning of the manufacturers is usually directed to push both ways in a supply chain: upstream to the suppliers and downstream to the customers. Contrastingly, for low-volume/high-customization product, the information flow triggered by the fluctuating customer demand usually propagates upward to the suppliers through the manufacturers. Furthermore, for R &D based hi-technology product like silicon wafer, the interactive information feedback mechanism between manufacturer and customer, which is essential to the new product development process, is to be embedded in the supply chain. This article is a case study of supply chain management system of LG Siltron, a major Korean silicon wafer manufacturer. The SCM system entails special information structure fitting well typical high-variety/high-customization product, and also gives application possibilities to the R&D based high-technology product made to the individual customer order.

• 한국전문물리치료학회지
• /
• 제29권4호
• /
• pp.255-261
• /
• 2022

Background: For the elderly, masticatory function is one of the most important oral functions and the masticatory ability is related to the wearing of dentures. Many older people wear dentures for their masticatory function, but a significant number of older people who use dentures have found that they feel uncomfortable when performing their daily activities, such as performing masticating functions or talking. Objects: The purpose of this study is to investigate how the forward head posture (FHP), respiratory function and thickness of masseter (MS), and sternocleidomastoid (SCM) are affected by the presence or absence of dentures in the elderly, and what kind of correlation there is between these variables. Methods: The study was conducted on 11 patients in the normal group and 13 in the denture group. The participant's cognitive ability was evaluated using Mini-Mental State Examination Korean (MMSE-K), and the FHP was evaluated by measuring the craniovertebral angle (CVA). The thickness of the MS and SCM muscles were measured using ultrasound, and respiration was measured with a spirometry. As for the statistical method, the correlation of each variable was investigated using Spearman's correlation coefficient. Results: In the normal group, there was a significant correlation between forced vital capacity (FVC) and forced expiratory volume in 1 second (FEV1) (p < 0.001), and in the denture group, FVC and FEV1 (p < 0.001), maximal inspiratory pressure (MIP) and maximal expiratory pressure (MEP) (p < 0.001), CVA and Lt. MS (p = 0.012). Conclusion: CVA and Lt. MS of the denture group have a high negative correlation, it is related that the thickness of MS may be thick when the elderly wearing dentures are FHP.

• 한국건설순환자원학회논문집
• /
• 제3권3호
• /
• pp.228-236
• /
• 2015

본 연구는 폐유지류를 중심으로 한 도포제 종류 및 도포시기에 따른 혼화재 다량치환 콘크리트의 탄산화 및 염해저항성에 미치는 영향에 관하여 실험 연구한 것이다. 즉 내구성 향상방안으로서, 도포시기를 탈형 즉시와 28일 수중양생후의 변화를 주고 도포제는 Plain인 Control을 포함한 ERCO(유화처리정제유지류), RCO(정제유지류), WR(발수제), ERCO+WR의 5가지 수준에 대하여 비교 실험을 실시하였다. 실험결과 도포시기에 따른 탄산화 및 내염해 저항성의 경우 28일 수중양생 후 도포의 경우 탄산화 및 염화물 침투 깊이가 감소하는 것을 알 수 있었고, 또한, 도포제는 ERCO, RCO, ERCO+WR, WR의 순으로 탄산화 및 염화물 침투깊이가 늦게 진행되어, 특히 ERCO의 도포가 탄산화 및 염화물 억제효과에 가장 우수한 것을 알 수 있었다.

• 한국지구과학회지
• /
• 제35권2호
• /
• pp.104-114
• /
• 2014

주풍에 따른 강수의 산성도, 전기전도도, 이온 성분의 변화를 알아보기 위하여 2009년 부산지역 강수를 분석하였다. 부산지역에서는 남서풍과 북동풍이 우세하게 나타났다. 주풍이 서풍인 경우, 강수의 산성도는 약 pH 7로 중성으로 나타났으나 전기전도도는 약 200 ${\mu}scm^{-1}$로 다른 풍향에 비해 월등히 높게 나타나 강수에 이온성분이 많이 함유된 것을 알 수 있었다. 양이온 $K^+$와 음이온 $Cl^-$가 다른 이온에 비해 높게 나타났으며, 북풍과 남서풍이 불 때 다른 풍향에 비해 전체적으로 높은 농도로 나타났다. 산성비의 주 원인물질인 $NO{_3}^-/SO{_4}^{2-}$의 구성비는 북풍에서 3 이상으로 월등히 높은 값이 나타났다. 다른 풍향에 비해 북동풍, 동풍, 남서풍, 서풍에서의 $K^+$의 중화기여도는 전체적으로 1 이상으로 높은 값을 나타내었는데, 이는 산성이온을 중화시키는데 있어서 알카리성 이온인 $K^+$의 중화기여도가 크게 작용하였음을 알 수 있다. 또한 해염입자는 북풍, 북동풍, 남서풍에서 800 ${\mu}sm^{-3}$ 이상으로 다른 풍향에 비해 상대적으로 많은 양을 나타내었다. 역궤적 분석 결과, 북풍, 서풍, 북서풍계열에서는 봄, 가을, 겨울철에 만주, 내몽골 고원, 중국, 러시아 지역으로부터 공기덩어리의 이동을 볼 수 있었다. 반면, 동풍, 북동풍, 남서풍계열에서는 여름철에 해양으로부터 공기덩어리의 이동을 볼 수 있었다. 따라서 부산지역의 강수중 산성도, 전기전도도, 이온 성분 농도는 내륙과 연안해역의 특성을 가진 주풍에 의한 변동 특성을 잘 나타내고 있음을 알 수 있었다.

• 한국항만경제학회지
• /
• 제30권4호
• /
• pp.219-254
• /
• 2014

최근 글로벌화와 SCM의 발전으로 인한 국제무역량의 증가는 물동량의 확대로 이어지고 있다. 해운 항만 물류환경의 변화로 컨테이너선의 대형화, 하역장비의 고성능화 항만운영의 글로벌화 및 급격한 기술의 변화가 해운항만에 많은 영향을 미치고 있으며, 이로 인해 경쟁력의 우위를 확보하는것은 이제 항만의 생존문제가 되고 있다. 항만 물동량이 많다는 것은 일반적으로 우세한 경쟁력을 지닌 항만이라고 할 수 있으나 다른 항만에 비해 효율적으로 운영되지 않으면 곧 경쟁력을 잃을 것이다. 반면에 특정시점에서 경쟁력이 낮은 항만일 지라도 효율성이 높은 항만은 경쟁력의 제고로 이어져 미래에는 우세한 항만이 될 수 도 있다. 본 연구에서는 동북아시아 항만간 물동량변화 추이 및 효율성 분석으로 항만경쟁력을 평가하여 국내항만의 경쟁력 제고방향을 제시하는데 그 목적이 있다. 이를 위한 실증분석에서는 항만물동량 성장추이와 경쟁우위를 파악할 수 있는 Shift-share기법과 DEA로 항만의 효율성을 분석하였다. 분석대상은 동북아시아 항만 총 21개로 하였으며, 두 기법의 결과를 종합적으로 분석하여 대상항만을 4가지 유형으로 구분하여, 동북아시아 항만 간 경쟁력 위치를 비교 분석하였다. 분석결과 우리나라의 대표적인 항만이 부산항은 여전히 성장세를 이어가고 있는 반면 인천항과 광양항은 성장추세가 둔화되고 있기 때문에 마케팅의 활성화와 항로의 다변화, 인센티브 제도 적극 실시 등을 통해 물동량 확보에 보다 집중해야 할 것이다.