• Corrosion Science and Technology
• /
• 제12권1호
• /
• pp.7-11
• /
• 2013

High velocity oxy-fuel (HVOF) spray coating of WC-metal powder (powder) was carried out to improve the resistances of friction, wear and corrosion of magnetic bearing shaft material Inconel718 (In718) of turbo blower. A micron sized WC-metal powder (86.5% WC, 9.5% Co 4% Cr) was coated onto In718 surface using HVOF thermal spraying. During the spraying, the binder metals and alloy such as Co, Cr and Co-Cr alloy were molten and a small portion of WC particles were partially decomposed to $W_2C$ and free carbon at above its decomposition temperature of $1250^{\circ}C$. The free carbon and excessively sprayed oxygen formed carbon oxide gases, resulting a porous coating of porosity of $2.2{\pm}0.3%$. The surface hardness of substrate increased approximately three times from 400 Hv of In718 to $1260{\pm}30Hv$ of the coating The friction coefficients of the coating were approximately $0.33{\pm}0.03$ at $25^{\circ}C$ and $0.26{\pm}0.03$ at $450^{\circ}C$. These values were smaller than those of In718 substrate at both temperatures due to the lubrication from the free carbon and the cobalt oxide debris. The corrosion resistance of the coating was higher than that of In718 both in salt water of 3.5% NaCl and acid of 1 M HCl solutions, on the contrary, it was lower in base solution of 1 M NaOH. According to this study, the HVOF WC-metal powder coating is recommended for the durability improvement of magnetic bearing shaft of turbo blower.

• 한국분말재료학회지
• /
• 제27권3호
• /
• pp.210-218
• /
• 2020

A T-800 (Co-Mo-Cr) coating material is fabricated using Co-Mo-Cr powder feedstock and laser cladding. The microstructure and melted Al erosion properties of the laser-cladded T-800 coating material are investigated. The Al erosion properties of the HVOF-sprayed MoB-CoCr and bulk T-800 material are also examined and compared with the laser-cladded T-800 coating material. Co and lave phases (Co₂MoCr and Co₃Mo₂Si) are detected in both the laser-cladded T-800 coating and the bulk T-800 materials. However, the sizes of the lave phases are measured as 7.9 ㎛ and 60.6 ㎛ for the laser-cladded and bulk T-800 materials, respectively. After the Al erosion tests, the erosion layer thicknesses of the three materials are measured as 91.50 ㎛ (HVOF MoB-CoCr coating), 204.83 ㎛ (laser cladded T-800), and 226.33 ㎛ (bulk T-800). In the HVOF MoB-CoCr coating material, coarse cracks and delamination of the coating layer are observed. On the other hand, no cracks or local delamination of the coating layer are detected in the laser T-800 material even after the Al erosion test. Based on the above results, the authors discuss the appropriate material and process that could replace conventional bulk T-800 materials used as molten Al pots.

• 한국추진공학회지
• /
• 제11권5호
• /
• pp.72-77
• /
• 2007

액체로켓엔진용으로 내부혼합 동축 와류형 분사기를 장착한 축소형 연소기에 대한 설계 및 연소시험결과를 기술하였다. 추진제는 액체산소 및 케로신이며 연소기는 분사기 헤드, 삭마냉각방식의 연소실 그리고 물냉각 노즐부로 구성되어 있다. 분사기 헤드는 액체산소 매니폴드, 연료 매니폴드, 중앙 분사기 그리고 내부혼합 형태의 18개 분사기로 이루어졌다. 축소형 연소기 연소시험은 성공적으로 이루어졌으며, 분사기의 손상이 발생하지 않았고 연소특성속도는 설계점에서 1756 m/sec을 나타내었다. 고주파 연소불안정은 나타나지 않았지만 탈설계점에서 압력의 저주파 섭동이 기준치를 넘는 결과를 보여주었다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2008년도 추계학술대회 초록집
• /
• pp.11-12
• /
• 2008

Micron-sized Co-alloy T800 powder was coated on Inconel718 (IN718) using high velocity oxygen fuel (HVOF) thermal spraying by the optimal coating process (OCP) determined from the best surface hardness of 16 coatings prepared by Taguchi program. The surface hardness improved 140-160 % from 399 Hv of IN718 to 560-630 Hv by the coating. Porosity of the coating was 1.0-2.7 %, strongly depending on spray parameters. Both friction coefficients (FC) and wear traces (WT) of the coating were smaller than those of IN718 substrate at both $25^{\circ}C$ and $538^{\circ}C$. FC and WT of IN718 and coating decreased with increasing the surface temperature. Tensile bond strength (TBS) and fracture location (FL) of Ti64/T800 were 8,770 psi and near middle of T800 coating respectively. TBS and FL of Ti64/NiCr/T800 were 8,740 psi and near middle of T800 coating respectively. This showed that cohesion of T800 coating was 8,740-8,770 psi, and adhesion of T800 on Ti64 and NiCr was stronger than the cohesion of T800.

• 한국분말재료학회지
• /
• 제12권2호
• /
• pp.136-145
• /
• 2005

Graphite-Ni composite powders were synthesized by mechanical alloying(MA) and spray drying(SD). Fabricated powders as well as commercial graphite-Ni powders were thermally sprayed on mild steel substrates using high velocity oxygen fuel (HVOF) thermal spray process and flame thermal spray process. The effects of several process parameters on related properties in thermally sprayed coatings have been investigated and correlated with microstructures in this study. The results indicated that the desired properties can be obtained when commercial powders were applied using HVOF process, while coating properties in case of MA powder application were inferior to those in HVOF process in so far. However, it is suggested that property enhancement can be obtained if the fraction of hexagonal graphite phase can be increased in mechanically alloyed powders.

• 한국산학기술학회논문지
• /
• 제12권9호
• /
• pp.4250-4256
• /
• 2011

활성증진 물질 Cu가 첨가된 Mn계 촉매를 제조하여 암모니아를 이용하여 질소산화물을 제거하는 SCR공정에서 질소산화물제거능을 측정하였다. 제조된 촉매를 사용하여 반응온도, 유량, 수분함량 그리고 산소농도에 대한 활성변화를 조사하였다. $H_2$-TPR 시스템에서 온도에 따른 촉매의 수소전환특성을 측정하였다. 수분공급유무를 조절함으로써 촉매반응에 대한 수분의 억제효과를 파악하였다. Mn-Cu계 촉매는 $160{\sim}260^{\circ}C$의 온도범위에서 높은 탈질효율을 보였다. 그리고 산소농도의 증가는 촉매활성 증진효과를 가져왔으나 수분함유는 촉매활성을 감소시키는 역할을 함을 알 수 있었다.

• 한국산학기술학회논문지
• /
• 제17권4호
• /
• pp.448-453
• /
• 2016

선박의 프로펠러나 임펠러와 같은 유체기기에서는 캐비테이션 현상으로 인해 마모와 침식이 발생한다. 이와 같은 기기손상은 소음과 진동을 발생시켜 기기수명을 단축시키는 문제점을 가지고 있다. 본 연구에서는 캐비테이션 현상에 대한 저항성을 높이기 위해 산업 현장에서 많이 사용되고 있는 고속화염용사코팅의 공정 최적화에 따른 각 요소별 중요도를 분석하였다. 다구찌 실험계획법을 적용하여 ALBC3 모재 표면에 비정질 분말을 코팅하였고 기공도 실험을 통해 각 요소별 특성을 분석하였다. 다구찌 실험계획법에 의해 고속 화염용사(HVOF) 코팅의 최적 공정을 찾아낸 결과 연소압이 80 psi, 코팅거리가 270 mm, 이송속도가 200 mm/s, 분말속도는 25 g/min으로 확인되었고, 그 결과, 연소압, 코팅거리 및 분말속도는 25% 이상으로 비슷한 기여도를 나타냈고 이송속도는 19%로 다소 떨어지는 수준을 나타내었다. 공정에 대한 각 인자별 기여도는 약간의 차이는 있지만 그 차이가 크지 않으므로 네 개의 인자 모두 고속 화염용사(HVOF) 코팅 공정에서 중요한 기여를 하였다.