• Journal of Biosystems Engineering
• /
• 제2권1호
• /
• pp.7-24
• /
• 1977

This paper is the forth and fifth one of the study on balanced type oscillating mole drainer. In the light of the results from previous reports about the model tests, some design criteria were established and a prototype machine was set up for experimental purpose. Motion characteristics and functionof the each parts of the machine were checked and analyzed. After that, performance tests of the prototype machine were carried out in thefield. Obtained results are summarized as follows ; 1. Ten centimeter of the bullet diameter was determined so as to be able to attach it to the tractors with capacity of 30 PS to 40 PS. 2. To maintain the balance between the moments of the front shank and rear shank, the oscillating amplitude of the rear bullet was determined to be larger than that of the front bullet. At the same time , the oscillating direction of the rear bullet was designed with the inclines of ten to thirty degrees. 3. An octagonal dynamo transduced was developed for measuring the compressive force of the upper link is measuring the draft force of the machine. Acceptable linear relationship between forces and strain responses from O.D.T. was obtained. 4. Analysing the balancing mechanism of the acting part of the machine , it was found that the total draft force of the machine was equal to the difference between the sum of the draft force produced from the right and left side bending moments of the lower drawber and the compressive force on the upper link. 5. There are acceptable linear relationship between the strain and twisting moment by driving shaft, and between strain and shank moment. Above results enable us to carry out the field experiment with prototype machine. 6. When the test machine was used in the field, it was possible to reduce the oscillating acceleration by forty percent in average as compared it with the single bullet mole drainer. 7. When the test machine was used under the oscillating condition, the dratt torce was reduced by 27 percent to 59 percent as compared it with the test machine under non-oscillating condition, while the draft force was increased by 7 percent to 20 percent as compared it with the mole drainer having oscillating single bullet. The reasoning behind this fact was considered as the resistance force due to the rear shank and bullet. 8. As the amplitude and frequency of the bullet were increased, the torque was increased accordingly. This tendency could be varied with the various characteristics of the given soils. And the larger frequency and amplitute, the more increasing oscil\ulcornerlating power but decreasing draft brce were needed, and draft force was increased as the velocity was increased.9. When the amplitude of the rear bullet was designed to be larger than that of the front bullet, the minimum value of the moment was lowered and oscillating acceleration was reduced. And when the oscillating direction of the rear bullet was declined back\ulcornerwards, oscillating acceleration was increased along with the increasing angle of decli\ulcornernation. When the test machine was operated in high speed, the difference between maximum moments and minimum ones became narrow. This varying magnitude of moments appeared on the moment oscillogram seems to be correlated to the oscillating acceleration and draft force. 10. From the analysis of variance, it was found that those factors such as frequency, amplitude, and operating velocity significantly affected in the oscillating acceleration, the draft resistance, the torque, the moment, and the total power required. And interaction between frequency and amplitude affected in the oscillating acceleration. 11. Within the given situation of this study, the most preferable operating conditions of the test machine were 7 Hz in oscillating frequency, 0.54 m/sec in operating velocity, and 39.1 mm in oscillating amplitude of front and rear bullets. However, it is necessary to select the proper frequency and magnitude of oscillation depending on the soil properties of the field in which the mole drainer is practiced by use of a bal1nced type oscillating mole drainer. 12. It is recommended that a comparative study of the mole drainers would be performed in the near future using two separate balanced oscillating bullet with the one which is operated by oscillating the movable bullet in a single cylinder or other balanced type which may be single oscillating bullet with spring, damper or balancing weight, and that of thing. To expand the applicability of the balanced type oscillating mole drainer in practical use, it is suggested to develop a new mechanism which perform mole drain with vinyl pipe or filling material such as rice hull.

• 구강회복응용과학지
• /
• 제34권2호
• /
• pp.80-88
• /
• 2018

목적: 임플란트 표면의 특성과 임플란트 디자인은 성공적인 초기 고정을 얻는데 중요한 변수이다. 이 연구의 목적은 치유기간 동안 테이퍼드 직선형 디자인을 가진 SLA (Sandblasted and Acid-etched) 임플란트의 ISQ (Implant Stability Quotient) 값을 측정하고 임플란트의 안정성에 미치는 영향을 평가하는 것이다. 연구 재료 및 방법: 임플란트의 안정성을 측정하기 위하여 26명의 환자(여자 13명, 남자 13명)의 44개 임플란트에 대한 자기공명주파수분석(Resonance Frequency Analysis)을 실시하였다. 골질 및 골량에 대한 임상적 평가는 Lekholm & Zarb (1985)의 기준에 따라 시행하였다. 시간경과에 따른 임플란트 안정성변화(총 ISQ 값)를 고정체 식립 시 그리고 12주후 치유지대주 연결 시 측정하고 RFA와 식립토크, RFA와 골질, RFA와 상, 하악골 사이의 상관관계를 평가하였다. 결과: 임플란트의 평균 ISQ값은 임플란트 식립 당시(기준선) $69.4{\pm}10.2$, 치유지대주연결에서(두번째수술) $81.4{\pm}6.9$였다(P < 0.05). RFA와 골질, RFA와 상하악골 사이에 유의한 차이가 있었다(P < 0.05). RFA와 식립토크, 식립부위, 고정체 직경, 임플란트 길이 사이에는 유의한 차이가 없었다(P > 0.05). 결론: 본 연구의 제한된 범위내에서 테이퍼드 직선형 디자인을 가진 SLA 임플란트의 ISQ값은 고정체 식립시와 치유지대주 연결 시 모두 높은 값을 보였다. 따라서 테이퍼드 직선형 디자인을 가진 SLA 임플란트는 초기안정성 및 2차 안정성을 향상시킬 수 있으며, 즉시 또는 초기하중을 적용할 수 있을것으로 사료된다.

• 한국가스학회지
• /
• 제18권6호
• /
• pp.27-31
• /
• 2014

본 연구에서는 LP가스 용기용 밸브에서 취약할 것으로 예상되는 Part 1, Part 2, Part 3 지역에 대한 강도안전성을 FEM으로 해석하였다. 밸브의 두께가 1.5mm이고, LPG 압력이 3.5MPa일 때 밸브의 Part 1 모서리 부분에서 27.5MPa의 Von Mises 최대응력이 걸리는 것으로 나타났다. 또한, 밸브의 두께가 1.5mm이고, LPG 압력 3.5MPa이 밸브에 작용할 때 Von Mises 최대응력은 Part 2에서 41.5MPa, 그리고 Part 3에서 46.5MPa으로 나타났다. 이러한 FEM 해석결과는 밸브의 Part 1, Part 2, Part 3에 작용하는 Von Mises 최대응력 모두가 황동소재 C3604의 항복강도 대비 9.2~15.5% 수준으로 대단히 낮은 값을 나타내고 있다. 이것은 기존의 LP가스 용기용 밸브의 두께가 지나치게 과도한 설계를 하였다는 것을 의미한다. 따라서, 밸브의 Part 1과 Part 2 지역의 두께는 황동밸브의 경량화 차원에서 얇게 설계하는 것이 바람직하다. 반면에 Part 3 지역의 두께는 기존의 밸브 두께처럼 두껍게 설계하여 높은 체결토크에도 안전한 강도를 유지하는 것이 좋다.

• 한국가스학회지
• /
• 제22권2호
• /
• pp.59-66
• /
• 2018

최근 무인기에 대한 관심과 수요가 높아지고 있는 가운데, 가동범위가 넓고 전략적으로 활용이 많은 고고도장기체공 무인기의 동력원개발이 연구 목표로 검토되었다. 기존 왕복동 엔진에 수소 연료를 적용하는 기술은 현행으로써 적용성이 용이하고 경제적이다. 수소는 중량당 에너지 밀도가 높아서 한 번 충전으로 장시간 운항을 지속할 수 있고 환경적인 측면에서도 무공해 연료라는 긍정적인 부분이 존재하기 때문에 적합하다고 평가된다. 하지만 현재 수소연료를 왕복동 엔진에 적용한 개발사례가 적은 편이라 향후 기술적으로 많은 연구가 필요한 것으로 판단된다. 항공기는 운항고도에 따라 공기밀도 저감으로 인한 냉각성능 저하 또는 복사열 감소에 의한 주변온도 강하로 과냉각이 될 수 있는 요인들이 존재한다. 따라서 본 실험은 냉각수온을 변화시켜서 이러한 주변온도 변화가 수소연료 엔진에 미치는 연소특성에 대해 살펴보았다. 역화에 의한 안정적인 운전 영역의 제한은 냉각수 온도변화에 의한 영향보다 공기과잉률에 의한 영향이 지배적으로 나타났으며, 냉각수 온도가 증가할 경우 충진효율이 감소하여 토크가 감소하고 냉각수 온도가 감소할 경우 열손실이 증가하여 열효율이 감소하였다.

• Journal of Periodontal and Implant Science
• /
• 제39권sup2호
• /
• pp.287-291
• /
• 2009

Purpose: The objective of this clinical presentation was to present a clinical case series report of socket preservation, sinus augmentation, and bone grafting using a horse-derived biomaterial. Methods: A horse-derived biomaterial was used in 8 patients for different indications including socket preservation following tooth extraction, osseous bone grafting, and sinus augementation procedures. Surgeries were performed by a well trained specialist and clinical radiographs were obtained at designated intervals. Biopsy cores of 2 ${\times}$ 8 mm prior to implant placement was obtained following a healing interval of 4 - 6 months. A clinical and histologic evaluation was performed to evaluate the clinical effectiveness and biocompatibility of the biomaterial. Results: All surgeries in 8 patients were successful with uneventful healing except for one case with membrane exposure that eventually resulted with a positive outcome. Radiographic display of the healing phase during different intervals showed increased radiopacity of granular nature as the healing time increased. No signs of adverse effect or infection was observed clinically and the tissues surrounding the biomaterial seemed well-tolerated with good intentional healing. The augmented sinuses healed uneventfully suggesting in part, good biocompatibility of the biomaterial. Dental implants placed following socket preservation were inserted with high initial torque suggesting good initial stability and bone quality. Conclusions: Our results show that at least on a tentative level, a horse-derived biomaterial may be used clinically in socket preservation, sinus augmentation, bone grafting techniques with good intentional healing and positive results.

• 비파괴검사학회지
• /
• 제22권5호
• /
• pp.490-499
• /
• 2002

국내 감마선투과검사용 조사장치는 1,000여대로 2,500여명의 종사자가 대부분 수동으로 원격 조작하는 실정으로 작업의 효율화와 방사선피폭 저감화를 위하여 자동 원격조작기의 사용이 요구된다. 이에 연구팀은 실무에 적합한 토크와 안전계수로부터 $54kgf{\cdot}cm$의 출력을 지닌 24V, 200W의 BLDC모터를 이용하여 $0.4{\sim}1.2m/s$ 범위의 선원 이동 속도를 조절할 수 있는 구동장치와 RF 센서로 구동 속도 조절, 광전센서에 의한 선원 위치 및 timer로 노출시간을 제어할 수 있는 무선 원격조작기를 개발하였다. 이와 같이 개발한 자동원격조작기는 AC 와 DC 겸용, 그리고 기존의 수통 원격조작기에 탈착이 가능하여 자동과 수동을 겸용할 수 있는 경제적 이점 등으로 활용도가 클 것으로 기대된다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권9호
• /
• pp.911-917
• /
• 2015

본 논문에서는 함정용 디젤연료를 단기통 커먼레일 디젤엔진에 적용하여 연료분사압력 변화에 따른 분사율 특성, 거시적 분무 특성 및 연료분사시기와 연료압력변화에 따른 연소 및 배기가스 배출특성을 분석하는데 초점을 두었다. 분사율 특성은 Bosch법을 적용한 분사율 측정 시험 장치를 이용하여 분석하였고, 거시적 분무 특성은 정적용기 및 초고속 카메라를 이용하여 분석하였다. 또한, 연료분사시기 및 연료압력 변화를 정밀하게 제어할 수 있는 단기통 엔진을 이용하여 연소 및 배기가스 배출특성을 분석하였다. 30MPa과 50MPa의 분사조건에서 초기 분사율은 50MPa의 분사조건에서 크게 나타났으며, 분무 발달(투과) 또한 동일시간대에서 큰 것으로 분석되었다. 연료분사시기가 지각될수록 실린더 내부 최대 압력과 최대 열발생량은 떨어지는 경향으로 나타났으며, 고압분사조건에서 실린더 내부 최대압력과 최대 열발생량은 다소 큰 것으로 분석되었다. 고압분사조건에서 도시평균유효압력은 낮은 것으로 분석되었고, 연료분사시기가 TDC 쪽으로 지각될수록 도시평균유효압력 및 토크는 증가하는 것으로 나타났다. 연료분사시기가 $BTDC20^{\circ}$(30MPa)와 $BTDC15^{\circ}$(50MPa)에서 질소산화물 발생수준이 가장 높았으며, 일산화탄소는 $BTDC30^{\circ}$를 기준으로 지각될수록 저감되었다.

• 대한치과보철학회지
• /
• 제33권4호
• /
• pp.780-806
• /
• 1995

The purpose of this study was to describe the application of 3D finite element analysis to determine resultant stresses on the bone anchored fixed prosthesis, implants and supporting bone of the mandible according to fixture numbers and load conditions. 4 or 6 fixtures and the bone anchored fixed prosthesis were placed in 3D finite element mandibular arch model which represents an actual mandibular skull. A $45^{\circ}$ diagonal load of 10㎏ was labiolingually applied in the center of the prosthesis(P1). A $45^{\circ}$ diagonal load of 20㎏ was buccolingually applied at the location of the 10mm or 20mm cantilever posterior to the most distal implant(P2 or P3). The vertical distribution loads were applied to the superior surfaces of both the right and the left 20mm cantilevers(P4). In order that the boundary conditions of the structure were located to the mandibular ramus and angle, the distal bone plane was to totally fixed to prevent rigid body motion of the entire model. 3D finite element analysis was perfomed for stress distribution and deflection on implants and supporting bone using commercial software(ABAQUS program. for Sun-SPARC Workstation. The results were as follows : 1. In all conditions of load, the hightest tensile stresses were observed at the metal lates of prostheses. 2. The higher tensile stresses were observed at the diagonal loads rather than the vertical loads 3. 6-implants cases were more stable than 4-implants cases for decreasing bending and torque under diagonal load on the anterior of prosthesis. 4. From a biomechanical perspective, high stress developed at the metal plate of cantilever-to-the most distal implant junctions as a consequence of loads applied to the cantilever extension. 5. Under diagonal load on cantilever extension, the 6-implants cases had a tendency to reduce displacement and to increase the reaction force of supporting point due to increasing the bendign stiffness of the prosthesis than 4-implants cases. 6. Under diagonal load on cantilever extension, the case of 10mm long cantilever was more stable than that of 20mm long cnatilever in respect of stress distribution and displacement. 7. When the ends of 10mm or 20mm long cantilever were loaded, the higher tensile stress was observed at the second most distal implant rather than the first most distal implant. 8. The 6-implants cases were more favorable about prevention of screw loosening under repeated loadings because 6-implants cases had smaller deformation and 4-implants cases had larger deformation.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.31-38
• /
• 2008

본 연구는 도시형 자기부상열차 부상레일의 롤 성형공정 해석에 대한 연구로서 성형공정의 타당성을 검증하기 위하여 부상레일과 유사형상인 트랙슈에 대한 롤 성형공정을 해석하였다. 해석과정은 초기 육면체의 블록에서 시작하여 총 12공정으로 이루어졌으며, 이중 중복되는 공정을 제외한 8개 공정에 대하여 해석을 수행하였다. 공정별 온도의 변화는 초기 $1200^{\circ}C$에서 1공정에 투입되는 30초 동안 표면의 온도는 $1010^{\circ}C$까지 냉각 되며, 최종 공정인 12공정에서는 중심부에서 $980^{\circ}C$, 표면은 $900^{\circ}C$로 냉각되었다. 아울러 각 공정별 소재의 길이변화는 롤 성형전의 블록을 1로 했을 경우 각 공정별로 소재의 길이변화를 초기 길이로 나누어 비율로 계산한 결과 최종 공정후 초기에 비해 5배 증가하는 것을 알 수 있었다. 소재의 변형률은 상부롤의 형상부에서 크게 나타났으며, 최소 2.5에서 최대 6.5의 변형률을 나타내었다. 각 공정별 상 하부롤의 토크는 초기 2, 3, 4공정에서 높게 나타났으며, 최대 $27,000ton{\cdot}mm$를 보였으며, 수직방향으로의 하중은 최대 300톤이 필요한 것으로 해석되었다.

• 대한치과보철학회지
• /
• 제38권4호
• /
• pp.526-543
• /
• 2000

Finite element analyses were performed to study effects on stress distribution generated in jaw bone for various shapes of dental implants: plateau type, plateau with small radius of curvature, triangular thread screw type in accordance with ISO regulations and square thread screw filleted with small radius partially. It was found that square thread screw filleted with small radius was more effective on stress distribution than other dental implants used in analyses. Additional analyses were performed on the implant with square thread screw filleted with small radius for very-ing design parameters, such as the width of thread end, the height of the thread of the implant and load direction, to determine the optimum dimensions of the implant. The highest stress concentration occurred at the region in jaw Pone adjacent to the first thread of the implant. The maximum effective stress induced by a 15 degree oblique load of 100 N was twice as high as the maximum effective stress caused by an equal amount of vertical load. Stress distribution was more effective in the case when the width of thread end and the height of thread were p/2 and 0.46p, respectively, where p is the pitch of thread. At last, using tensile force calculated from the possible insert torque without breading bone thread, finite element analysis was performed on the implant to calculate pre-stress when the primary fixation of the implant was operated in jaw bone. The maximum effective stress was 136.8 MPa which was proven to be safe.