• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.4
• /
• pp.114-125
• /
• 1994

Fatigue behavior and life prediction method were presented for themal-mechanical and isothermal low cycle fatigue of 12 Cr forged steel used for high temperature applications. In-phase and out-of-phase thermal-mechanical fatigue test from 350 .deg. C to 600 .deg. C and isothermal low cycle fatigue test at 600 .deg. C, 475 .deg. C, 350 .deg. C were conducted using smooth cylindrical hollow specimen under strain-control with total strain ranges from 0.006 to 0.015. The phase difference between temperature and strain in thermal-mechanical fatigue resulted in significantly shorter fatigue life for out-of-phase than for in-phase. Thermal-mechanical fatigue life predication was made by partitioning the strain ranges of the hysteresis loops and the results of isothermal low cycle fatigue tests which were performed under the combination of slow and fast strain rates. Predicted fatigue lives for out-of-phase using the strain range partitioning method showed an excellent agreement with the actual out-of-phase thermal-mechanical fatigue lives within a factor of 1.5. Conventional strain range partitioning method exhibited a poor accuracy in the prediction of in-phase range partitioning method in a conservative way. By the way life prediction of thermal-mechanical fatigue by Taira's equivalent temperature method and spanning fartor method showed good agreement within out-of-phase thermal-mechanical fatigue.

• Korean Journal of Metals and Materials
• /
• v.48 no.1
• /
• pp.28-38
• /
• 2010

High temperature high cycle and low cycle fatigue deformation behavior of automotive heat resistant aluminum alloys (A356 and A319 based) were investigated in this study. The microstructures of both alloys were composed of primary Al-Si dendrite and eutectic Si phase. However, the size and distribution for eutectic Si phase varied: a coarse and inhomogeneous distributed was observed in alloy B (A319 based). A brittle intermethallic phase of ${\alpha}-Fe\;Al_{12}(Fe,Mn)_3Si_2$ was detected only in B alloy. Alloy B exhibited high fatigue life only under a high stress amplitued condition in the high cycle fatigue results, whereas alloy A showed high fatigue life when stress was lowered. With regard to the low-cycle fatigue result ($250^{\circ}C$) showing higher fatigue life as ductility increased, alloy A demonstrated higher fatigue life under all of the strain amplitude conditions. Fractographic observations showed that large porosities and pores near the outside surface could be the main factor in the formation of fatigue cracks. In alloy B. micro-cracks were formed in both the brittle intermetallic and coarse Si phasese. These micro-cracks then coalesced together and provided a path for fatigue crack propagation. From the observation of the differences in microstructure and fractography of these two automotive alloys, the authors attempt to explain the high-temperature fatigue deformation behavior of heat resistant aluminum alloys.

• Korean Chemical Engineering Research
• /
• v.56 no.5
• /
• pp.732-737
• /
• 2018

Experimental data of phase equilibria are reported for the binary mixture of 1-phenyl-2-pyrrolidone in supercritical carbon dioxide. Phase behavior data was measured in a synthetic method at a temperature ranging from 333.2 to 393.2 K and at pressures up to 97.14 MPa. The solubility of 1-phenyl-2-pyrrolidone in the carbon dioxide + 1-phenyl-2-pyrrolidone system increased as temperature increased at a constant pressure and it exhibited the type-I phase behavior. The experimental data for the binary mixture were correlated with the Peng-Robinson equation of state using mixing rule and the critical properties of 1-phenyl-2-pyrrolidone were predicted with the Joback and Lyderson method.

• Advances in nano research
• /
• v.1 no.2
• /
• pp.93-103
• /
• 2013

An ultrasonic-mediated assisted stepwise method has been developed for depositing transparent ZnO films from aqueous solution. Rinsing in low ethylene glycol temperature was easy to produce intermediate phase of $Zn(OH)_2$, rinsing in $120^{\circ}C$ ethylene glycol was observed the diffraction peak of intermediate $Zn(OH)_2$ in early report, the rinsing temperature plays an important role in the process of $Zn(OH)_2$ phase transformed to ZnO, high rinsing temperature actually improved the intermediate phase. However, the effect of rinsing on the intermediate phase is yet to be understood clearly. The effect of different rinsing procedures, involving either of or a combination of successive ionic layer adsorption and reaction (SILAR) and ultrasonic-assisted rinsing, prior to hydrolysis in ethylene glycol was found to improve the occurrence $Zn(OH)_2$ in ZnO thin films. In the zinc complex ($[Zn(NH_3)_4]^{2+}$) solution, excess ($[Zn(NH_3)_4]^{2+}$) absorbed in glass substrate transformed incompletely to ZnO and exist as $Zn(OH)_2$ phase in thin films. In films deposited at low temperature, rinsing procedure is applied to improve excess $Zn(OH)_2$ and obtain smoother transparent thin films.

• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.5
• /
• pp.249-256
• /
• 2006

Structural studies have been performed on precipitation hardening found in $L1_2$ ordered ${\gamma}^{\prime}-Ni_3(Al,Ti)$ alloys using transmission electron microscopy. A uniform solid solution of ${\gamma}^{\prime}-L1_2$ ordered phase supersaturated with Ni can be obtained by solution annealing in a suitable temperature range. The ${\gamma}^{\prime}$ phase hardens appreciably by the fine precipitation of disordered ${\gamma}$. The shape of ${\gamma}$ precipitates formed during aging is initially spherical or round-cubic and grow into platelets as aging proceeds. High resolution electron microscopy revealed that the ${\gamma}$ precipitates are perfectly coherent with the matrix ${\gamma}^{\prime}$ as long as the ${\gamma}$-precipitates are plates. The loss of coherency initiates by the introduction of dislocations at the ${\gamma}/{\gamma}^{\prime}$ interface followed by the step formation at the dislocations. The ${\gamma}$ precipitates become globular after the loss of coherency. The strength of ${\gamma}^{\prime}-Ni_3(Al,Ti)$ increases over the temperature range of experiment by the precipitation of fine ${\gamma}$ particles. The peak temperature where a maximum strength was obtained shifted to higher temperature.

• Journal of Powder Materials
• /
• v.13 no.1 s.54
• /
• pp.46-51
• /
• 2006

Through the volume change of Sn in a low-temperature phase transformation, the Sn nanopowder with high, purity, was fabricated by an economic and eco-friendly process. The fine cracks were spontaneously generated. in, Sn ingot, which was reduced to powders in the repetition of phase transformation. The Sn nanopowder with 50 run in size was obtained by the 24th repetitions of phase transformation by low-temperature and ultrasonic treatments. Also, the $SnO_2$ powder was fabricated by the oxidation of the produced Sn powder to the ingot and milled by the ultrasonic milling method. The $SnO_2$ nanopowder of 20 nm in size was fabricated after the milling for 180 h.

• Journal of Korea Foundry Society
• /
• v.40 no.2
• /
• pp.16-24
• /
• 2020

The effect of a heat treatment on the microstructure and mechanical properties of Inconel 713C alloy vacuum investment castings were investigated. The microstructure of the as-cast state was observed, showing well-developed dendrite structures and distributed carbide particles and solidified massive precipitates in the grain or grain boundary during solidification, in this case the γ′ phase and MC particles. During a heat treatment, the γ phase matrix was reinforced by solid solution elements, carbide particles from the film morphology precipitated along the grain boundary, and many micro-precipitates of second γ′ phases 0.2 ㎛~2 ㎛ in size were newly formed in the γ phase matrix according to SEM-EDS analysis results. The tensile strength at a high temperature (850℃) decreased slightly becoming comparable with the room-temperature result, while the hardness value of the specimen after the vacuum heat treatment increased by approximately 19%, becoming similar to that of the as-cast condition. However, the impact values at room temperature and low temperature (-196℃) were approximated; this alloy was mostly not affected by an impact at a low temperature. In the observations of the fracture surface morphologies of the specimens after the tensile tests, the fractures at room temperature were a mix of brittle and ductile fractures, and an intergranular fracture in the inter-dendrite structure and some dimples in the matrix were observed, whereas the fractures at high temperatures were ductile fractures, with many dimples arising due to precipitation. It was found that a reinforced matrix and precipitates of carbide and the γ′ phase due to the heat treatment had significant effects, contributing greatly to the excellent mechanical properties.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.371-374
• /
• 1995

The real-time holographic interferometer with a digital high-speed camera is applied to the visualization of transient temperature field. Collimated and diffused laser beams are used to the object beam according to the shape and transmittance of the phase object. Also, ESPI(Electronic Speckle Speckle Pattern Interferometer) technique is used to the visualization and quantitatie measurement of slow-varying temperature field. The experimental results obtained form these two techniques are discussed.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.6
• /
• pp.443-450
• /
• 2023

SiC/SiC_f CMC is vulnerable to water vapor corrosion at a high temperature of 1500℃. So, EBC (Environmental Barrier Coating) materials are required to protect Si-based CMCs. Ytterbium silicates are reported to have coefficient of thermal expansion (CTE) similar to that of the base material, such as SiC/SiC_f CMC. When the EBC are materials exposed to high temperature environment, the interface between ytterbium silicates and SiC/SiC_f CMC is not separated, and the coating purpose can be safely achieved. For the perspective of EBC applications, thermally grown oxide (TGO) layer with different CTE is formed by the reaction with water vapor in EBC, which leads to a decrease in life time. In this study, we prepare two types of ytterbium silicates to observe the corrosion behavior during the expose to high temperature and water vapor. In order to observe this behavior, the steam-jet furnace is prepared. In addition, phase formation of these ytterbium silicates is analyzed with microstructures by the before/after steam-jet evaluation at 1500℃ for 100 h.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.4
• /
• pp.558-563
• /
• 1996

Fracture strength of $Si_{3}N_{4}/20$ vol% SiC nanocomposites with fifferent sintering additives was measured. Strength of nanocomposites with 6 wt% $Y_{2}O_{3}$ and 2 wt% $Al_{2}O_{3}$ as sintering additives was higher at room temperature but significant strength degradation at elevated temperature was occured due to the softening of grain boundary phase. Fracture strength of 8 wt% $Y_{2}O_{3}$ doped sample was higher than that of $Al_{2}O_{3}$ added sample at $1400^{\circ}C$. The retention of high temperature strength in 8 wt% $Y_{2}O_{3}$ doped sample can be attributed to high softening temperature and crystallization of grain boundary glassy phase.