• Journal of Korea Foundry Society
• /
• v.33 no.5
• /
• pp.215-225
• /
• 2013

The alloys required for fossil power plants are altered from stainless steel that has been used below $600^{\circ}C$ to Ni-based alloys that can operate at $700^{\circ}C$ for Hyper Super Critical (HSC) steam turbine. The IN740 alloy (Special Metals Co. USA) is proposed for improved rupture strength and corrosion resistance at high temperature. However, previous studies with experiments and simulations on stable phases at about $700^{\circ}C$ indicated the formation of the eta phase with the wasting of a gamma prime phase, which is the most important reinforced phase in precipitation hardened Ni alloys, and this resulted in the formation of precipitation free zones to decrease the strength. On the basis of thermodynamic calculation, the new Ni-based superalloy named LESS 1 (Low Eta Sigma Superalloy) was designed in this study to improve the strengthening effect and structure stability by depressing the formation of topologically close packed phases, especially sigma and eta phases at high temperature. A thermal exposure test was carried out to determine the microstructure stability of LESS 1 in comparison with IN740 at $800^{\circ}C$ for 300 hrs. The experimental results show that a needle-shaped eta phase was formed in the grin boundary and it grew to intragrain, and a precipitation free zone was also observed in IN740, but these defects were entirely controlled in LESS 1.

• ETRI Journal
• /
• v.41 no.6
• /
• pp.820-828
• /
• 2019

A highly reliable conductive adhesive obtained by transient liquid-phase sintering (TLPS) technologies is studied for use in high-power device packaging. TLPS involves the low-temperature reaction of a low-melting metal or alloy with a high-melting metal or alloy to form a reacted metal matrix. For a TLPS material (consisting of Ag-coated Cu, a Sn96.5-Ag3.0-Cu0.5 solder, and a volatile fluxing resin) used herein, the melting temperature of the metal matrix exceeds the bonding temperature. After bonding of the TLPS material, a unique melting peak of TLPS is observed at 356 ℃, consistent with the transient behavior of Ag₃Sn + Cu₆Sn₅ → liquid + Cu₃Sn reported by the National Institute of Standards and Technology. The TLPS material shows superior thermal conductivity as compared with other commercially available Ag pastes under the same specimen preparation conditions. In conclusion, the TLPS material can be a promising candidate for a highly reliable conductive adhesive in power device packaging because remelting of the SAC305 solder, which is widely used in conventional power modules, is not observed.

• Transactions of Materials Processing
• /
• v.13 no.3
• /
• pp.205-210
• /
• 2004

The waveguide Bragg gratings have been fabricated by the phase-mask method. An excimer laser with maximum 600mJ output pulse energy and uniform phase masks have been used. Hydrogen loading is often used for enhancing the uv photosensitivity of the core, however, the resultant gratings show significant aging effect. In the present study, high temperature thermal annealing process has been investigated to obtain thermal gratings and process parameters are deduced.

• Journal of Korean Society for Atmospheric Environment
• /
• v.6 no.1
• /
• pp.85-96
• /
• 1990

Simultaneous removal efficiencies of hydrophilic and hydrophobic gaseous pollutants are experimentally determined, and the macroscopic removal mechanism of pollutants in a dry scrubber is analyzed using the extended model of three phase equilibrium distribution of pollutant at high temperatures that can describe the different morphological conditions of adsorbent and water at varying relative humidities. For the simplicity, the inside of spray dryer is divided into three regions of ; (1) absorption, (2) three-phase equilibrium, and (3) adsorption, and the removal efficiencies of each pollutants at three regions are observed at different experimental conditions to estimate the effects of important parameters of dry scrubber. The laboratory experiments simulate the three regions of spray dryer with the temperature control and thus evaporation rate of water from the slurry particle. $SO_2$ as a hydrophilic gaseous pollutant and vinyl chloride as a hydrophobic toxic gas are selected for the future field application to soid waste incineration, and the two types of slurry are made of the two sorbents ; 10 wt.% $Ca(OH)_2$, and 10 wt.% NaOH. Result of temperature effect shows the height of absorption plus three-phase region is decreased as the operation temperature is increased, which results in the lower removal efficiency of $SO_2$ but higher removal for vinyl chloride in the adsorption region of dry scrubber. The removal efficiency of $SO_2$ is higher by NaOH slurry than by $Ca(OH)_2$ slurry due to the hygroscopic nature of NaOH, while the removal of vinyl chloride is higher in $Ca(OH)_2$ case. From the analysis of redults using three-phase equilibrium distribution model, the effective two-phase partition coefficients can be obtained, and the possible extention in the application of the three-phase equilibrium model in a dry scrubber design has been demonstrated.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.1
• /
• pp.39-43
• /
• 2007

The pure CrN powders oxidized to $Cr_2O_3$ noticeably above $850^{\circ}C$ in air. When these powders were sintered into bulk samples at $1500^{\circ}C$ under 40 atm of $N_2$ pressure, the CrN phase partly changed into the $Cr_2N$ phase, owing to the partial loss of nitrogen from CrN. When the bulk sample was heated at $1000-1200^{\circ}C$ for 100 hr under vacuum, the CrN phase also progressively changed into $Cr_2N$. At the same time, a relatively thin $Cr_2O_3$ layer formed on the bulk sample due to the reaction of chromium with residual oxygen in vacuum.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1999.05a
• /
• pp.124-124
• /
• 1999

An ultrasonic method is developed for the measurement of the two-phase mixture level in the reactor vessel or steam generator. The ultrasonic method is selected among the several non¬nuelear two-phase mixture level measurement methods through two steps of selection procedure. A commercial ultrasonic level measurement method is modified for application into the high temperature, pressure, and other conditions. The calculation method of the ultrasonic velocity is modified to consider the medium as the homogeneous mixture of air and steam. and to be applied into the high temperature and pressure conditions. The cross-correlation technique is adopted as a detection method to reduce the effects of the attenuation and the dif.JUsed reflection caused by suface fluctuation. The waveguides are developed to reduce the loss of echo and to remove the effects of obstructs. The present experimental study shows that the developed ultrasonic method measures the two-phase mixture level more accurately than the conventional methods do.

• Journal of Technologic Dentistry
• /
• v.31 no.4
• /
• pp.25-30
• /
• 2009

Zirconia($ZrO_2$) has attracted much attention in science and technology because of its high refractive index, high melting temperature, hardness, low thermal conductivity and corrosion barrier properties. And it is widely used as the dental restoration material because of its esthetic appearance. In this research, we analyzed the particle size and composition of the imported dental porcelain for zirconia. And the glass frit was produced. To decrease the glass transition temperature and softening temperature of the glass frit, $Li_2O$ was added into it and the effect of $Li_2O$ on the firing temperature was researched. Then the glass which contains leucite crystal with a high coefficient of thermal expansion(CTE) was manufactured and it was mixed with the glass frit to control the CTE. The phase composition were analyzed using the X-ray diffraction. The morphologies of the samples were observed by the scanning electron microscope. The 4wt% $Li_2O$-added glass frit has the optimal glass transition temperature and softening temperature. And 6 wt% leucite crystal was mixed with the glass frit to control the CTE. From the experimental results of crystallization, the crystal phase was found only leucite crystal.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.94-97
• /
• 2005

Bismuth high Tc superconducting thin films are fabricated via a co-deposition process by an ion beam sputtering with an ultra low growth rate, and sticking processing of the respective elements are evaluated. The sticking processing of bismuth element in bismuth high Tc superconducting thin film formation was observed to show a unique temperature dependence; it was almost a constant value of 0.49 below about $730^{\circ}C$ and decreased linearly over about $730^{\circ}C$. This temperature dependence can be elucidated from the evaporation and sublimation rates of bismuth oxide, $Bi_2O_3$, from the film surface. It is considered that the liquid phase of the bismuth oxide plays an important role in the bismuth phase formation in the co-deposition process.

• Proceedings of the KAIS Fall Conference
• /
• 2001.05a
• /
• pp.287-289
• /
• 2001

The morphology of silica supported MoO$_3$ catalysts, which was prepared by impregnation of ammonium heptamolybdate with various weight loadings up to 35 wt%, was studied using x-ray diffraction. In addition to the orthorhombic phase, the behavior of the rarely studied hexagonal phase was characterized. For high loading catalysts, excess ammonium ions present in the monoclinic and triclinic precursors are capable of occupying interstitial sites of microcrystalline MoO$_3$ during moderate temperature calcinations and in doing so enhance the MoO$_3$-SiO$_2$ interaction. This results in a "well dispersed" morphology at high loadings. Sintering at high temperature is due to loss of ammonium from the oxide framework. Ammonia reimpregnation, which leads back to the well dispersed hexagonal phase, may offer a simple regeneration process for spent Mo containing catalysts.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.193-197
• /
• 2004

The effect of the temperature dependence of the smectic layer spacing in the smectic-A (SmA) phase on the formation of defects in the ferroelectric smectic-$C^{\ast}$ ($SmC^{\ast}$) phase is investigated with x-ray scattering technique. The study is based on thin parallel-aligned surface stabilized ferroelectric liquid crystal cells with two different alignment conditions, high pretilt $SiO_x$, alignment and low pretilt polyimide films. It is found that defects observed in the $SmC^{\ast}$ phase have much more profound dependence on the layer changes and chevron formation in the SmA phase than in the $SmC^{\ast}$ phase. We find that thermal layer expansion with decreasing temperature in the SmA phase suppresses the formation of defects observed in the SmC phase.