• 한국전기전자재료학회논문지
• /
• 제19권8호
• /
• pp.701-706
• /
• 2006

In addition to its similarity to genuine diamond film, diamond-like carbon (DLC) film has many advantages, including its wide band gap and variable refractive index. In this study, DLC films were prepared by the RF PECVD (Plasma Enhanced Chemical Vapor Deposition) method on silicon substrates using methane $(CH_4)$ and hydrogen $(H_2)$ gas. We examined the effects of the post annealing temperature on the structural variation of the DLC films. The films were annealed at temperatures ranging from 300 to $900^{\circ}C$ in steps of $200^{\circ}C$ using RTA equipment in nitrogen ambient. The thickness of the film and interface between film and substrate were observed by surface profiler, field emission scanning electron microscopy (FESEM), high resolution transmission electron microscopy (HRTEM), respectively. Raman and X-ray photoelectron spectroscopy (XPS) analysis showed that DLC films were graphitized ($I_D/I_G$, G-peak position and $sp^2/sp^3$ increased) ratio at higher annealing temperature. The variation of surface as a function of annealing treatment was verified by a AFM and contact angle method.

• Archives of Metallurgy and Materials
• /
• 제64권3호
• /
• pp.875-878
• /
• 2019

Microstructures and mechanical properties of as-cast Al-6.5Mg-1.5Zn-0.5Fe alloys newly alloy-designed for the parts of automobile were investigated in detail. The aluminum (Al) sheets of 4 mm thickness, 30 mm width and 100 mm length were reduced to a thickness of 1mm by multi-pass rolling at ambient temperature and subsequently annealed for 1h at 200~500℃. The as-cast Al sheet was deformed without a formation of so large cracks even at huge rolling reduction of 75%. The recrystallization begun to occur at 250℃, it finished at 350℃. The as-rolled material showed tensile strength of 430 MPa and tensile elongation of 4.7%, however the specimen after annealing at 500℃ showed the strength of 305 MPa and the elongation of 32%. The fraction of high angle grain boundaries above 15 degree increased greatly after annealing at high temperatures. These characteristics of the specimens after annealing were discussed in detail.

• 열처리공학회지
• /
• 제23권6호
• /
• pp.331-337
• /
• 2010

Aluminum nitride (AlN) thin films containing various amounts of Co content have been deposited by using a two-facing targets type sputtering (TFTS) system. The deposited films were also annealed successively and isothermally at different temperatures. Annealing treatment can control the physical properties as well as the microstructure of AlN films with Co particles. High magnetization and high resistivity are obtainable in AlN films containing dispersed Co particles. The coercivity of the films does not depend on annealing time, but it increases with increasing annealing temperature due to the increase of the grain size. A high saturation magnetization of 46 kG and resistivity of 2200 ${\mu}{\Omega}$-cm was obtained for AlN films containing 25 at% Co.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1932-1938
• /
• 2003

We have applied spectroscopic ellipsometry to investigate $high-{\kappa}$ dielectric thin films and correlate their optical properties with fabrication processes, in particular, with high temperature annealing. The use of high-k dielectrics such as $HfO_{2}$, $Ta_{2}O_{5}$, $TiO_{2}$, and $ZrO_{2}$ as the replacement for $SiO_{2}$ as the gate dielectric in CMOS devices has received much attention recently due to its high dielectric constant. From the characteristics found in the pseudo-dielectric functions or the Tauc-Lorentz dispersions, the optical properties such as optical band gap, polycrystallization, and optical density will be discussed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 춘계학술회의 초록집
• /
• pp.21-21
• /
• 2010

(Ba,Sr)$TiO_3$ (BST) thin film with a perovskite structure has potential for the practical application in various functional devices such as nonvolatile-memory components, capacitor, gate insulator of thin-film transistors, and electro-optic devices for display. Normally, the BST thin films derived from sol-gel and sputtering are amorphous or partially crystalline when processed below $600^{\circ}C$. For the purpose of integrating BST thin film directly into a Si-based read-out integrated circuit (ROIC), it is necessary to process the BST film below $400^{\circ}C$. The microstructural and electrical properties of low-temperature crystallized BST film were studied. The BST thin films have been fabricated at $350^{\circ}C$ by UV-assisted rapidly thermal annealing (RTA). The BST films are in a single perovskite phase and have well-defined electrical properties such as high dielectric constant, low dielectric loss, low leakage current density, and high breakdown voltage. Photoexcitation of the organics contained in the sol-gel-derived films by high-intensity UV irradiation facilitates elimination of the organics and formation of the single-crystalline phase films at low temperatures. The amorphous BST thin film was transformed to a highly (h00)-oriented perovskite structure by high oxygen pressure processing (HOPP) at as low as $350^{\circ}C$. The dielectric properties of BST film were comparable to (or even better than) those of the conventionally processed BST films prepared by sputtering or post-annealing at temperature above $600^{\circ}C$. When external pressure was applied to the well-known contractive BST system during annealing, the nucleation energy barrier was reduced; correspondingly, the crystallization temperature decreased. The UV-assisted RTA and HOPP, as compatible with existing MOS technology, let the BST films be integrated into radio-frequency circuit and mixed-signal integrated circuit below the critical temperature of $400^{\circ}C$.

• Journal of Korean Vacuum Science & Technology
• /
• 제6권3호
• /
• pp.120-125
• /
• 2002

The aim of the present work is to optimized the annealing parameter in both front and back screen printed contacts realization on p-type multicrystalline silicon and with phosphorus diffused. The RTA treatments were carried out at various temperatures from 600 to 850$\^{C}$ and annealing time ranging from 3 min to 5 min in air, O$_2$and N$_2$ ambiance. The contacts parameters are obtained according to Transmission Line Model measurements. A good RTA cycle is obtained with a temperature plateau of 700$\^{C}$-750$\^{C}$ and annealing ambiance of air. Several processing parameters required for good cell efficiency are discussed with an emphasis placed on the critical role of the glass frit in the aluminum paste. A anamolus behaviour of Aluminum n-doping on p-type Si wafer, contact at high temperature have also been studied.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.318.1-318.1
• /
• 2016

Hafnium Oxide (HfOx) has been attracted as a promising gate dielectric for replacing SiO2 in gate stack applications. In this paper, Metal-Oxide-Semiconductor (MOS) capacitor with solution processed HfO2 high-k material as a dielectric were fabricated. The solvent using $HfOCl2{\cdot}8H2O$ dissolve in 2-Methoxy ethanol was prepared at 0.3M. The HfOx layers were deposited on p-type silicon substrate by spin-coating at $250^{\circ}C$ for 5 minutes on a hot plate and repeated the same cycle for 5 times, followed by annealing process at 350, 450 and $550^{\circ}C$ for 2 hours. When the annealing temperature was increased from 350 to $550^{\circ}C$, capacitance value was increased from 337 to 367 pF. That was resulted from the higher temperature of HfOx which have more crystallization phase, therefore dielectric constant (k) was increased from 11 to 12. It leads to the formation of dense HfOx film and improve the ability of the insulator layer. We confirm that HfOx layer have a good performance for dielectric layer in MOS capacitors.

• 한국전기전자재료학회논문지
• /
• 제19권4호
• /
• pp.334-338
• /
• 2006

Poly silicon TFT requires high quality dielectric film; conventional method of growing silicon dioxide needs highly hazardous chemicals such as silane. We have grown high quality dielectric film of silicon dioxide using non-hazardous chemical such as TFOS and ozone as reaction gases by APCVD. The films grown were characterized through C-V curves of MOS structures. Conventional APCVD requires high temperature processing where as in the process of current study, we developed a low temperature process. Interface trap density was substantially decreased in the silicon surface coated with the silicon dioxide film after annealing in nitrogen ambient. The interface with such low trap density could be used for poly silicon TFT fabrication with cheaper cost and potentially less hazards.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.570-573
• /
• 2001

In this paper, GaN films have been grown on SiO$_2$/Si(100) substrates by RF magnetron sputtering. To obtain high quality GaN films, we used ZnO buffer layer and modified the process conditions. The charateristics of GaN films on RF power, substrate temperature and Ar/N$_2$gas ratio have been investigated by Auger electron spectroscopy and X-ray diffraction analysis. At RF power 150W, substrate temperature 500 $^{\circ}C$ and Ar/N$_2$=1:2 gas ratio, we could grow high quality GaN films. Through the atomic force microscope and photoluminescence analysises, it was observed that the crystallization of GaN films was improved with increasing annealing temperature and the optimal crystallization of GaN films was found at 1100 $^{\circ}C$ annealing temperature.

• 한국재료학회지
• /
• 제25권7호
• /
• pp.347-351
• /
• 2015

To study the characteristics of ZTO, which is made using a target mixed $ZnO:SnO_2=1:1$, the ZnO and $SnO_2$ were analyzed using PL, XRD patterns, and electrical properties. Resulting characteristics were compared with the electrical characteristics of ZnO, $SnO_2$, and ZTO. The electrical characteristics of ZTO were found to improve with increasing of the annealing temperature due to the high degree of crystal structures at high temperature. The crystal structure of $SnO_2$ was also found to increase with increasing temperatures. So, the structure of ZTO was found to be affected by the annealing temperature and the molecules of $SnO_2$; the optical property of ZTO was similar to that of ZnO. Among the ZTO films, ZTO annealed at the highest temperature showed the highest capacitance and Schottky contact.