• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.2
• /
• pp.671-678
• /
• 2019

In this paper, the low cycle fatigue failure and ratcheting behavior, as well as their interaction of AH32 steel were experimentally investigated under uniaxial cyclic loading. The effects of mean stress, stress amplitude and stress ratio on the low cycle fatigue life and ratcheting strain were discussed. It was found that the ratcheting strain increased while the fatigue life decreased with the increase of mean stress and stress amplitude, and the increasing stress ratio would result in smaller ratcheting and larger fatigue life. Two kinds of failure modes, i.e. low cycle fatigue failure due to crack propagates and ratcheting failure due to large plastic strain will take place respectively. Based on the experimental results, considered the effect of ratcheting on fatigue life, a model with the maximum stress and ratcheting strain rate was proposed. Comparison with the experimental result showed that the new model provided a good prediction for AH32 steel.

• Parasites, Hosts and Diseases
• /
• v.22 no.2
• /
• pp.153-160
• /
• 1984

An experimental study was undertaken to observe the difference in susceptibility of mouse strains to Metagonimus yokogawai infection by estimating it from worm recovery rate and dimension of worms. It was also studied the effects of prednisolone injection on the chronological pattern of worm recovery in ICR mice. The metacercariae were obtained from sweetfish and 300 in each number were given to 5 strains (CBH, A, DBA, $C^{57}BL$ and KK) of mice, and after 7 days period, the worms were collected from their intestine. Prednisolone at the dose of 10 mg/kg was injected to ICR mice every other day from 7 days prior to infection until sacrificed at 6 hours to 35th post-infection day. ICR mice infected with M. yokogawai but untreated were used for controls. The success rate in infection of mice ranged 25.0-83. 3% by strains, the worm recovery rate 1. 2-18. 9%, and the average size of worms O. 554-0. 683 mm long and 0.214-0.244 mm wide. The higher rates and larger size of worms were observed in KK and $C^{57}BL$ strains than others and the difference was statistically significant. In ICR mice for control, the worm recovery rate until 1 day after infection was relatively high (38-66%) but it became much lower (less than 0.7%) during 1-35 days. However, prednisolone injection brought about persistently high recovery rates (16-80%) until 21 days. It was concluded that the susceptibility to M. yokogawai infection is different by strains of mice but it can be elevated by prednisolone injection probably due to suppression of Immune respon3e3 in ICR mice.

• Korean Journal of Metals and Materials
• /
• v.50 no.10
• /
• pp.703-710
• /
• 2012

The effects of the ordering reaction on high temperature mechanical behavior is investigated by tensile tests at $2{\times}10^{-2}/s-3.3{\times}10^{-5}/s$ up to $745^{\circ}C$. The tensile deformed region is examined by differential scanning calorimeter (DSC), TEM, and high resolution neutron diffraction (HRPD). The results showed that a plateau of tensile strength appeared at $150-500^{\circ}C$ whereas the elongation minimum occurred at about $600^{\circ}C$. This suggests that the occurrence of a plateau does not cause the elongation minimum. The temperature of the elongation minimum decreases with the strain rate. HRPD results show a lattice contraction in the tensile deformed specimen at the temperature of the plateau occurring region. The plateau of tensile strength, the lattice contraction, and the occurrence of serration appeared in the same temperature region.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.3
• /
• pp.275-282
• /
• 2012

In this study, tensile tests were performed using standard and notched-bar specimens under two different displacement rates and various temperatures, in order to investigate the effects of the stress and strain concentration at the notched section on the dynamic strain aging (DSA) behavior of carbon steel piping material. In addition, finite element simulations were conducted to evaluate quantitatively the stress and strain states for both types of specimen under uniaxial tensile loading. The results showed that serration and an increase in tensile strength, which are considered to be evidence of DSA in carbon steels, can be observed from tensile tests for notched-bar specimens. It was also found that the temperature region of DSA observed in the notched-bar specimens was higher than the DSA region observed in the standard tensile specimens tested under the same displacement rate. The results of finite element analysis showed that this behavior is associated with the high strain rate at the notched section, which is caused by the stress and strain concentration.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.211-215
• /
• 2000

A new methodology is presented to evaluate material properties at high strain rates and high temperatures based on orthogonal metal cutting experiments and FEM simulations. Average strain rate and average temperature found in the deformation zone are computed and flow stress data at these conditions are modified until cutting forces calculated in simulations match those determined in experiments. Material properties obtained from this method were verified by additional metal cutting simulations. Derivation from cutting forces measured in experiments was less than 10%. The feasibility of tool design using FEM simulations is also demonstrated.

• Nuclear Engineering and Technology
• /
• v.53 no.9
• /
• pp.2953-2959
• /
• 2021

A new practical modeling of the Norton's power law creep is proposed and implemented to analyze the high temperature behaviors of Alloy 690 SG tube material. In the model, both the stress exponent n and the rate constant B are simply treated as the temperature dependent parameters. Based on the two-step optimization procedure, the temperature function of the rate constant B(T) was determined for the data set of each B value after fixing the stress exponent n value by using the prior optimized function at each temperature. This procedure could significantly reduce the numerical errors when using the power law creep equations. Based on the better description of the steady-state creep rates, the experimental rupture times could also be well predicted by using the Monkman-Grant relationship. Furthermore, the difference in tensile strengths at high temperatures could be very well estimated by assuming the imaginary creep stress related to the given strain rate after correcting the temperature effects on the elastic modulus.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.48-53
• /
• 2007

The objective of this paper is to investigate the influence of impact conditions on the impact characteristics of the stainless sheet for the case of the fixed boundary conditions. In order to examine impact characteristics of the sheet, three-dimensional finite element analyses and impact tests have been performed. High speed tensile tests have been carried out to obtain strain-stress relationships including the effects of the strain rate. In order to improve an accuracy of the FE analysis, the hyper-elastic model and the damping factor have been introduced. The results of the FE analyses and the impact tests have been shown that the diameter of the impact head does not affect the absorption energy of the stainless sheet. In addition, it has been shown that the absorption rate of energy maintains almost $82.5\;\sim\;83.5\;%$ irrespective of the impact energy level and the diameter of the impact head. From the results of FE analyses, the variation of stress and strain energy in the stainless sheet has been quantitatively examined.

• Corrosion Science and Technology
• /
• v.22 no.5
• /
• pp.341-350
• /
• 2023

In the present study, effects of a thin Zn-flash coating on hydrogen evolution, infusion, and embrittlement of advanced high strength steel during electro-galvanizing were examined. The electrochemical permeation technique in conjunction with impedance spectroscopy was employed under applied cathodic polarization. Moreover, a slow-strain rate test was conducted to evaluate loss of elongation (i.e., indicative of hydrogen embrittlement (HE)) and examine fracture surfaces. Results showed that the presence of a thin Zn-flash coating, even when it was not distributed uniformly, reduced hydrogen evolution rate and substantially impeded infusion of hydrogen into the steel substrate. This was primarily due to a hydrogen overvoltage on Zn coating and trapping of hydrogen at the interface of Zn coating/flash coating/steel substrate. Consequently, the sample with flash coating had a smaller HE index than the sample without flash coating. These results suggest that a thin Zn-flash coating could be an effective technical strategy for mitigating HE in advanced high-strength steels.

• Journal of Biosystems Engineering
• /
• v.15 no.3
• /
• pp.219-229
• /
• 1990

The compression creep behavior of grains when loaded depends not only on load but also on duration of load application. The most common methods of studying the load-time characteristics of agricultural products is by employing rheological models such as Burger's model. However it is sometimes not sufficient to describe the viscoelastic behavior of grains to be Burger's model. For this reason, this study was conducted to develop the rheological model which represented the creep compliance response of the rough rice kernel and was a function of initial stress applied and time. The effects of the initial stress applied and the moisture content on the compression creep behavior of the rough rice kernel were analyzed. The results were obtained from the study as follows: 1. Since the viscoelastic behavior of the rough rice kernel was nonlinear, the transient and steady state creep compliance was satisfactorily modelled as follows: $$J({\sigma},t)=A{\sigma}^B[C+Dt-exp(-Ft)]$$ But, for the every stress applied, the compression creep behavior of the samples tested can be well described by Burger's model respectively. 2. The creep compliance, the instantaneous elastic strain, the retarded elastic strain and the viscous strain of the sample tested generally increased in magnitude with increasing the applied initial stress and the moisture content used in the tests. At low moisture content, the creep compliance for the Japonica-type rough rice kernel Was a little higher than those for Indica-type and at high moisture content, vice versa at high moisture content. 3. The retardation times of the samples had not an uniform tendency by the initial stress and the moisture content. The retardation times ranged from 0.66 to 6.76 seconds, and the creep progressed from transient to steady state at a relatively high rate. 4. The less viscous strain than the instantaneous elastic strain for the samples tested indicated that rough rice kernel behaved as a viscoelastic body characterized by elasticity than viscosity.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.5
• /
• pp.1562-1572
• /
• 1996

The rigid-plastic finite element formulation including the inertia force is derived and then the rigid-plastic finite elemnt program considering the inertia effect is developed. In order to consider the strain hardening, strain rate hardening and thermal softening effects which are frequentrly observed in high-velocity deformation phenomena, the Johnson-Cook constitutive odel is applied. The developed program is used to simulate two high-velocity deformation problemss ; rod impact test and hdigh-velocity compression precess. As a result of rod impact test simulation, it is found that the siulated result has a good agreement with the experimental observation. Through the high-velocity compression process simulation. it is also found that the accuracy of the simulated results is dependent upon the time increment size and mesh size.