• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.2
• /
• pp.100-106
• /
• 2013

Stainless steel has some excellent properties as the material for the mechanical component. Purpose of this study is carried out to obtain mirror surface on the surperfinishing of stainless steel with high efficiency. To achieve this, we have conducted a series of polishing experiment for stainless steel using abrasive film from the perspective of oscillation speed, the rotational speed of workpiece, contact roller hardness, contact pressure and feed rate. Abrasive film used this study is a micro-finishing film and a lapping film. Furthermore, the polishing characteristics and efficiency of stainless steel is discussed through measuring optimal polishing time and surface roughness. From the obtained results, it was confirmed that efficient superfinishing conditions and polishing characteristic of Stainless steel can be determined.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.277-277
• /
• 2012

New concept of coating process, which is called Electro Magnetic Levitation-Physical Vapour deposition (EML-PVD) was developed and investigated. Zinc coating was performed and succeeded for the first time on the steel strip (Cold-rolled Steel) in a continuos pilot line using the EML-PVD process which is specialized in the high deposition rate and high vapor yield. EML-PVD will be expected to be the next generation coating technology to be applied to the steel industry.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.429-430
• /
• 2002

In this study, three kinds of brake: discs including two coated brake discs and one steel disc were tested under the same experimental conditions on a reduced scale braking test bench. Plasma spray coating technique was used to coat ceramic powder on the discs. In the test, four commercial sintered brake pads were coupled with discs. Ceramic coated discs have shown good stability in friction coefficient at high speed and high energy braking conditions. However, ceramic coated discs caused more wear loss of pad mass than the steel disc. It was shown that thermal barrier effect in ceramic coated discs adjusted the thermal partition between pad and disc. Steel disc showed fluctuating friction coefficient at high speed but less wear loss of pad mass than ceramic coated discs.

• Transactions of Materials Processing
• /
• v.22 no.4
• /
• pp.223-228
• /
• 2013

The friction coefficients of advanced high strength steel sheets were experimentally determined. In the friction test, the pulling and holding forces acting on the sheet for various friction conditions, such as lubricant viscosity, pulling speed, blank holding pressure, sheet surface roughness, and hardness of the sheet were measured and the friction coefficient was calculated based on Coulomb's friction law. While the friction coefficient, generally, decreases as the value of friction factor increases, the factor associated with the sheet surface roughness shows U shape behavior for the friction coefficient. Furthermore, the relationship between friction coefficient and the wear volume, which was computed for the roughness of both sheet surfaces and the friction area, is linearly proportional.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.1
• /
• pp.9-14
• /
• 2013

In recent years, high hardness steel is used for most of the material in many areas including aircraft, nuclear power, space exploration and automotive parts. Low CBN tools are widely used in industrial field which can effectively process high hardness steel of HRC 45 or harder. The results of this study demonstrated, when high hardness steel, SCM440 is turned with Low CBN tools coated with TiN and TiAlN coatings respectively, that both the thrust force and cutting force tends to increase with more increase in cutting force than thrust force, as the feed rate increases at constant cutting speed. In addition, the size of the cutting force and thrust force does not change with the increased cutting speed at the same feed rate, but the tool life is reduced if the cutting speed is increased to shorten the machining time. Therefore, it is recommended to limit the cutting speed at 250 m/min maximum or less. Furthermore, comparing the cutting force of the three tools at the same cutting condition, Tin coating tool showed the smallest cutting force and Low CBN was the next, and the TiAlN coating tools showed the largest cutting force.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.1
• /
• pp.7-15
• /
• 2008

Currently existing high-accuracy and high-speed die sets used in reciprocal press create scratches at the surface of guide posts, steel balls, and bushes due to vertical movement of balls with point-contacts between inner surface of bushes and guide posts. Consequently, accuracy of the die set and the life span of the metal mold are reduced. However, those scratches could reduce the pre-load of the steel ball. This research designed and developed a groove-type die set which improves life span of the die set by eliminating point-contacts of steel balls with guide posts. The guide post consisted of a steel-ball retainer, a steel-ball retainer stopper, a guide bush, a guide pin, a snap ring, and a spring. The steel-ball retainer has 72 holes with 8 columns of 9 holes in each column. The inner surface of the guide bush was grinded(surface roughness: $Ra\;\\;0.2{\mu}m$, accuracy: $0\;{\sim}\;-0.002mm$) after NC turning and heat treatment. Also, a line of small intermediate pocket was processed inside of the guide bush for lubrication and elimination of foreign materials. Guide grooves of steel balls were processed using a wire EDM(Electrical Discharge Machining) after heat treatment. With such a design of the guide post stated above, loads against steel balls could be dispersed greatly by the line contacts through the guide groove between the guide post and the guide bush, and the life span of the guide post could be expanded semi-permanently.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.6
• /
• pp.761-771
• /
• 2008

When the crossing frequency of a train meets the natural frequency of a railway bridge, the bridge is bound to become resonant. There are few available time response samples involving a train that passes a bridge at high speed. Very effective modal-parameter extraction techniques for such special high-speed railway bridge conditions are introduced in this paper. Utilizing the cross-correlations of the free-vibration responses after the train passes, mode shapes and the temporal modal parameters (e.g., natural frequency and damping ratio) are extracted using the TDD and SI techniques, respectively. This approach has been applied to a two-span steel composite bridge in the Kyung-Bu high-speed railway system. The estimation results were compared with those obtained using the existing methods. The results fully coincide with those that were extracted using the existing aforementioned technique.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.190-196
• /
• 1993

Internal high speed grinding under several high grinding wheel speed condition has been performed in this study for the effects have analyzed and compared with the grinding power, grinding tangential force and accuracy of surface with the carbon tool steel(SK3). The following results have been obtained: (1) Under the workpiece speed constant condition, increasing the grinding speed, the tangential force is decreased, and on the contrary, accuracy of surface is improved. (2) Under the speed ratio (V$_{w}$/V$_{s}$) contant condition it is possible to increase the high machining efficiency constraint to tangential grinding force constant.ant.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.875-880
• /
• 2007

Due to increasing demands for environment-friendly railway system, bronze wires with cadmium, which is a potential environmental hazard, have been no longer permitted as messenger wire for electric railway system. One of materials being considered as the replacements is copper-clad steel conductor(CCSC), which is currently used as contact wire for high speed operation in the Japanese shinkansen. However, there have been few studies for the application as messenger wire by the CCSC. This study deals with requirements and performances of the messenger wire stranded by the CCSC, especially for high speed electric railway. And the tentative evaluation items and methods to be specified as the Korean railway standard(KRS) are proposed.

• Journal of Korean Society of Steel Construction
• /
• v.8 no.3 s.28
• /
• pp.47-54
• /
• 1996

Recently Sucessive progress in train technic has enabled us to constructed high-speed railways for ourselves. This caused more rapid train more pressure on a track and speedier track break-down. Especially in the construction of high-speed rails for high-speed traveling and safety accurate breaking distance is essential and not only computation of rolling resistance in theory but also verification through real measurement are important in basic material for breaking and starting load caused during the train running. In this study, we measured traveling resistance and calculated traveling resistance formula in the case of the SAEMA-EUL which consists of main part of current passenger trains and frights in this country.