• Tribology and Lubricants
• /
• v.33 no.1
• /
• pp.15-22
• /
• 2017

Because the running speed of vehicles is increasing and a shorter braking distance is required, high heat-resistant brake pads are needed to satisfy the requirements of customers and car makers. In the near future, hazardous materials such as Cu, Cr, Zn, and Sb will be restricted from use in friction materials. Ceramic composites reinforced by carbon fibers are good candidates for eco-friendly friction materials. In this study, we develop ceramic composite friction materials. The friction materials are composed of carbon fibers, Si, SiC, graphite, and phenol resin and are prepared by hot forming and heat treatment at high temperatures. The density, void ratio, and compressive strength are $1.59-1.66g/cm^3$, 16.6-20, and 70-90 MPa, respectively. Friction and wear tests are performed using a pin-on-plate-type reciprocating friction tester at 25, 100, and $200^{\circ}C$. The counterpart material is a CrMoV steel extracted from a KTX brake disc. Friction coefficient, wear amount, and wear mechanism are measured and examined. We determine that the friction coefficients depend on the temperature and the fluctuation of the friction coefficients is larger at higher temperatures. The amount of wear increases with the surface temperatures of the specimens. The tribological properties of the developed composites are similar to those of a Cu-based sintered friction material. Through this study, it is confirmed that ceramic composite materials can be used as friction materials.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.11
• /
• pp.9-16
• /
• 2011

We need to establish standard for the ICT based on train control system. In order to solve the ISI problem, this paper evaluate the performance of OFDM and FDE system. We seem that OFDM system is better than FDE system. In order to solve ISI problem, SC System is needed a equalizer. And another method is OFDM System. If system is used SC with a equalizer, It is better than OFDM in terms of PAPR, but this system is not easy to use Multi-Antenna technique, i.e., beam-forming and MIMO-multiplexing. And If system is used high-order modulation, BER performance is worse than OFDM. If we think about in terms of PAPR problem, considerations are considered not significant because the size of relays is not considered in the communication between trains and ground.

• Journal of the Korean Society for Railway
• /
• v.16 no.3
• /
• pp.169-174
• /
• 2013

The effect of modifying the shape of a high-performance EMU train on the aerodynamic drag is studied here using Computational Fluid Dynamics(CFD) based on three dimensional Steady-state Navier-Stokes equation and two equation turbulence modeling. FLUENT 12 and Gambit 2.4.6 are employed for a numerical simulation of the aerodynamic drag of a streamlined-shape train as well as a proto type train. The characteristics of the aerodynamic drag of trains in tunnels are analyzed in a comparison with these characteristics in an open space. The contribution of the aerodynamic drag of each case is also investigated to establish principal pertaining to drag reduction for urban trains in tunnels. The aerodynamic drag of a streamlined train was reduced to 9.8% relative to a proto-type train with a blunt nose and a protruding roof facility and underbody shape: the running resistance is expected to be reduced by as much as 4% at a running speed of 80km/h.

• Journal of the Korean Society for Railway
• /
• v.20 no.2
• /
• pp.165-172
• /
• 2017

High frequency squeal noise can be generated when a railroad vehicle runs a sharp curved section; this noise causes environmental complaints and excessive wear on the wheel and the railroad track. In this paper, curved squeal noise experiments on a commercial railway were carried out to investigate this phenomenon. The relationship of the squeal noise pressure level, the frequency characteristics, the railway running speed, and the modal behavior of the wheel were investigated. At the same time, the lateral motion of the wheel relative to the rail was captured using a video camera; wheel movement was calculated when the noise was generated. queal noise occurred at the highest level at the inner front wheel; this phenomena is considered to be related to the lateral vibration response characteristics of the wheel. It can be seen that the magnitude of this squeal noise is not directly related to the increase in vehicle speed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.12
• /
• pp.782-789
• /
• 2020

The demand for the development of rolling stock technology to maintain the best performance in various climatic environments has increased to expand the overseas market of rolling stock. In this study, international and domestic standards that must be applied to build a harsh climatic environment test system were investigated and compared. The way of improvement for domestic standards is proposed. The wind velocities and temperatures are specified in the UIC, EN, and IEC standards for climatic wind tunnel, and EN 50125-1 provides the velocity test up to 180km/h, the largest wind speed. UIC and EN provide the lowest temperature of -45℃, and IEC 62498-1 provides the highest temperature 55℃. The solar radiation test was specified up to 1200W/m2 in the UIC, EN, and IEC. The IEC, EN, and KS R 9145 provide the water tightness standards, which are different from each other in water capacity, pressure, and methods. The snow test method was not well specified. KRTS-VE-Part 31 provides pressurization test methods. The airtightness standards for high-speed rolling stock are defined and regulated for internal pressure change rate in UIC 660 and 779-11. The domestic standard for the wind tunnel test was not well prepared, and the solar radiation test and snow test do not exist in Korea. Therefore, it is necessary to improve domestic standards to an international level for the climatic wind tunnel test of rolling stock.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1255-1261
• /
• 2010

An operating information and fault recode of train is very important information for safety driving and maintenance. And these information is increased and need high speed as the number of trains is increased. Wireless LAN or CDMA network is efficient to report more complicated and various information from vehicle to server in control center. Existing wireless transmission system has weakness due to transmission system is separated with TDCS and standalone. At first, standalone system needs space to be installed and cost is increased. And data transmission capacity and speed is limited by complicated structure that transmission system receive data thru serial communication like RS232 and then data transmission system send data to server in control center. This article is study to develop embedded & wireless fault code transmission device to be installed in TDCS to overcome weakness of space and to have more cost effective and simple structure. It is adapted 802.11b/g WiFi for wireless communication and OS is used embedded Linux that can easily implement wireless communication environment and ensure TCP/IP communication’s security. We also implement simple server to test wireless communication between embedded & wireless fault code transmission device and server in control center.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.10
• /
• pp.1014-1023
• /
• 2008

Subway electric trains need to be faster for accommodation of long distance passengers. The faster run of the existing trains results in deterioration of ride quality due to noise and vibration. To reduce the noise and vibration of the electric train, a running test of the electric train was performed and an ADAMS/Rail model was set up to verify the running test results. The experimental results show that the sources of the cabin noise and vibration basically comes from the irregularity of the railroad track and the deterioration of the connection part between cabin and bogie. Consequently for mitigation of noise and vibration of the electric train, the redesign of the center pivot with softer stiffness and the minimization of rail irregularity are necessary. the frequent maintenance of the train will lead to better comport.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1715-1721
• /
• 2011

For an efficient railroad operations the demand forecasting is required. Time series models can quickly forecast the future demand with fewer data. As well as the accuracy of forecasting is excellent compared to other methods. In this study is proposed the intervention ARIMA model for forecasting methods of KTX passenger demand. The intervention ARIMA model may reflect the intervention such as the Kyongbu high-speed rail project second phase. The simple seasonal ARIMA model is predicted to overestimate the KTX passenger demand. However, intervention ARIMA model is predicted the reasonable results. The KTX passenger demands were predicted to be a week units separated by the weekday and weekend.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1888-1893
• /
• 2011

Considering the dynamic performance and stability of railroad vehicles has begun to grab the attention because of developing the high speed train recently. A development based on an analysis of dynamics and verification has to be required to study the stability of vehicle performance. Several ways of analysis were using the look-up table to apply the wheel-rail contact characteristics quickly, whereas there is a constraint of the wheelset lateral displacement. In this study, an development of searching the wheel-rail contact position has been provided. The 2-point contact between wheel and rail during the driving condition can be calculated by numerical analysis. Moreover, a reliability is verified by comparing the result with a commercial program.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1282-1288
• /
• 2011

Recently, the demand regarding reliability and safety of the railroad are increased as built to high-speed railway and Driverless LRT systems. Accordingly, effective management of construction projects is being applied, with the introduction and use of PMIS computerized systems. Due to the construction of railways, from the start of PMIS research planning, design, procurement, to construction and commissioning, various expertise is being carefully gathered, and by integrating it into the unified budget ideas and processes, rational, efficient, organized, and manageable financial plans are developed for the computerized system. However, the current PMIS does not take into account the life-cycle. Therefore, this study is to bring attention to the BIM smart BOM-based configuration management for life-cycle through the consideration for railway construction project management.