• 한국수소및신에너지학회논문집
• /
• 제32권5호
• /
• pp.356-364
• /
• 2021

During the hydrogen fueling process, hydrogen temperature inside the compressed tank were limited below 85℃ due to the allowable pressure of tank material. The chiller system to cool compressed hydrogen used R407C, greenhouse gas with a high global warming potential (GWP), as a refrigerant. To reduce greehouse gas emission, it should be replaced by refrigerant with a low GWP. This study proposes a chiller system for fueling hydrogen with R290, consisted in propane, by applying the C3 pre-cooled system use d in the LNG liquefaction process. The proposed system consisted of hydrogen compression and cooling sections and optimized the operating pressure through exergy analysis. It was also compared to the exergy efficiency with the existing system at the optimal operating pressure. The result showed that the optimal operating pressure is 700 kPa in 2-stage, 840 kPa/490 kPa in 3-stage, and the exergy efficiency increased by 17%.

• 한국군사과학기술학회지
• /
• 제8권4호
• /
• pp.146-151
• /
• 2005

The burning rates of combustible cartridge cases(CCCs) of 120mm kinetic energy ammunition were measured by CBT(Closed Bomb Tester). The burning coefficient was 1.4 for CCC fabricated by Post Impregnation(PI) process, and 1.0 for that by Beater Additive(BA) process. The BA process CCC showed the fixed burning coefficient of 1.0 in spite of changing the composition of CCC. As the Korean Future Main Battle Tank is requiring the high penetration performance compared with that of KlAl tank ammunition(K276), CCC was designed to have higher impetus composition than that of K276 composition(525J/g). The optimum impetus was 600J/g when considering the increases of pressure and muzzle velocity with increasing impetus. When impetus of CCC by changing the composition increased from 525J/g to 600J/g, the muzzle velocity of 12m/s at pressure increase of 3500psi increased in case of using SCDB propellant.

• 동력기계공학회지
• /
• 제8권1호
• /
• pp.41-47
• /
• 2004

Cooling towers are widely used not only for cooling products and equipment in manufacturing process but HVAC(Heating, Ventilation and Air Conditioning) system. As a cooling tower is the terminal apparatus which discharges heat from industrial process, the efficiency of heat exchange in the cooling tower greatly affects to the overall performance of a thermal system. In this paper, we constituted a new water cooling system by using a Latent heat of evaporation in an enclosed tank, and this system is consisted of an enclosed vacuum tank and water driven ejector system. Several experimental cases were carried out for improvement methods of high vacuum pressure and water cooling characteristics. The ejector performance was tested in case of water temperature variations that flows into the ejector. Based on the vacuum pressure by water driven ejector, the water cooling characteristics were investigated for the vaporized air condensing effects.

• Design & Manufacturing
• /
• 제10권2호
• /
• pp.18-23
• /
• 2016

Injection molded thermoplastic parts may need to be coated to facilitate paint adhesion, or to satisfy other surface property requirements, such as appearance, durability, and weather resistance. In this paper, a two-component polyurethane metering system was developed for the simultaneous injection and surface coating of a plastic substrate. The system was composed of storage tanks, feed pumps, axial piston pumps, mixing head. The tank was designed to be double-jacket structured and fabricated for polyol and isocyanate, respectively. A temperature chamber was used to maintain the material temperature to be $80^{\circ}C$ during flowing from storage tank to mixing head. Inside the chamber, feed pump, low pressure filter, high pressure pump, high pressure filter, pressure sensor, flow meter were installed. A mixing head of L-type was used for homogeneous mixing of polyol and isocyanate. Inside the mixing head, a cartridge heater and a temperature sensor were installed to control the temperature of the materials. The flow rate of axial-piston pump was controlled by using closed-loop feedback control algorithm. The input flow-rates were compared with the measured values. The output error was 6.7% for open-loop control, whereas the error was below 2.2% for closed-loop control. In addition, the pressure generated through mixing-head nozzle increased with increasing flow rate. It was found that the pressure drop between metering pump and mixing-head nozzle was almost 10 bar.

• Journal of Advanced Research in Ocean Engineering
• /
• 제3권1호
• /
• pp.41-52
• /
• 2017

This paper presents a numerical and experimental study of sloshing loads on liquefied natural gas (LNG) vessels. Conventional LNG carriers with membrane-type cargo systems have filling restrictions from 10% to 70% of tank height. The main reason for such restrictions is high sloshing loads around these filling depths. However, intermediate filling depths cannot be avoided for most LNG vessels except the LNG carrier. This study attempted to design a membrane-type LNG tank with a modified lower-chamfer shape that allows all filling operations. First, numerical sloshing analysis was carried out to find an efficient height of the lower-chamfer that can reduce sloshing pressure at partially filled conditions. The numerical sloshing analysis program SHI-SLOSH was used for numerical simulation; this program is based on SOLA-VOF. The effectiveness of the newly designed tanks was validated by 1:50-scale three-dimensional tank tests. A total of three different tanks were tested: a conventional tank and two modified tanks. As test conditions, various filling depths and wave periods were considered, and the same test conditions were applied to the three tanks. During the test, slosh-induced dynamic pressures were measured around the corners of the tank wall. The measured pressure data were post-processed and the pressures of the three different tanks were statistically compared in several ways. Experimental results show that the modified tanks were quite effective in reducing sloshing loads at low filling conditions. This study demonstrated the possibility of all filling operations for LNG cargo containment systems.

• 한국구조물진단유지관리공학회 논문집
• /
• 제11권2호
• /
• pp.164-174
• /
• 2007

댐에서 관로 시스템을 효과적으로 설계하기 위해서는 수격작용과 같은 과도수리현상을 해석해야 만 한다. 일반적으로 조압수조는 터빈의 부하변화에 의한 과도수리현상에 의해 발생되는 압력의 변화를 감소시키기 위해서 사용된다. 본 연구에서는 댐 안전관리를 위한 조압수조의 적정규모를 조사하였다. 지배방정식을 이용하여 조압수조 내 수위변동을 계산하였다. Thoma-Jaeger의 안정조건을 사용하여 홍수위, 상시만수위, 정격수위, 저수위인 경우에 정적안정조건과 동적안정조건을 검토하였다. 끝으로 조압수조의 수직갱과 수실의 적정 지름을 결정하였다.

• 한국안전학회지
• /
• 제32권4호
• /
• pp.129-136
• /
• 2017

This study investigated the probability of possible accident through qualitative and quantitative analysis of the pressure safety valve types installed in facilities using high pressure gas to compare the installation domestic and foreign pressure safety valve standards sought the safety characteristics and safety improvement direction accordingly. The three types are the case where the shut-off valve is not installed at the front of the PSV (Case A), If a shut-off valve is installed at the front of the PSV for inspection (Case B) and If a shut-off valve is installed in front of PSV (C.S.O), PSV is installed in parallel (Case C). Three types of cases were compared with FTA and HAZOP. The results of study of the possible accidents due to over-pressure safety valve installation type, used in a high-pressure gas facilities was shows in the following order Case B > Case A > Case C. The results of analysis through FTA was in order to protect the reservoir for the possible occurring of accident the safety valve installation is depend on its type. In the FTA analysis, defects in the device itself which attached to the storage tank as a substitute for analysis of the probability of operator mistakes was Case B with as high as $2.01{\times}10^{-6}$. Depending on the type of installation analysis of Case B in order to ensure safety is prohibited to install shut-off valve and believes that mandatory regulations are needed. Rationally installing of pressure safety valve in the high pressure using facilities will be expected to improve the industrial safety from severe accidents such as high-pressure gas fire explosion.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.857-858
• /
• 2012

• 한국전산유체공학회지
• /
• 제10권4호통권31호
• /
• pp.59-65
• /
• 2005

A numerical analysis was made to investigate the simple silencer for high pressure blast flow fields. Reynolds-Averaged Navier-Stokes equations were solved for an axisymmetric computational domain constructed by multi block grids. A blast flow field without the silencer was also calculated to validate the present numerical method. The effect of pressure diminution for the silencer was calculated by comparing with and without silencer at the atmosphere region. It was found that the tested silencer could achieve 89.4 percent pressure diminution.

• 한국분무공학회지
• /
• 제24권3호
• /
• pp.130-136
• /
• 2019

Spray visualization of a vaporizer fuel injection system of a micro turbo jet engine was experimentally studied. The fuel heating by combustion was simulated by the high pressure steam generator and combustor inlet air from the centrifugal compressor was simulated by compressed air stored in the high pressure air tank. Spray visualization was performed with single vaporizer, and then six vaporizers which are same number of micro turbojet engine were used. As a results, the spray characteristics of the vaporizer were understood with pressure difference of the combustor inlet air and the fuel supply pressure. Spray angles with three types of vaporizer configuration were measured. In the results, guide vane configuration has a wider spray angle than the straight tube and smooth curve tube with a swirler, so it is expected that the fuel will be effectively distributed inside the combustor flame tube.