• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.251-254
• /
• 2007

Principal challenges to $\underline{direct\;fabrication}$ of high performance a-Si:H transistor arrays on flexible substrates include automated handling through bonding-debonding processes, substrate-compatible low temperature fabrication processes, management of dimensional instability of plastic substrates, and planarization and management of CTE mismatch for stainless steel foils. Viable solutions to address these challenges are described.

• Structural Engineering and Mechanics
• /
• 제62권2호
• /
• pp.209-224
• /
• 2017

Elevated water tanks are considered as important structures due to its post-earthquake requirements. Elevated water tank on reinforced concrete frame staging is widely used in India. Different response reduction factors depending on ductility of frame members are used in seismic design of frame staging. The study on appropriateness of response reduction factor for reinforced concrete tank staging is sparse in literature. In the present paper a systematic study on estimation of key components of response reduction factors is presented. By considering the various combinations of tank capacity, height of staging, seismic design level and design response reduction factors, forty-eight analytical models are developed and designed using relevant Indian codes. The minimum specified design cross section of column as per Indian code is found to be sufficient to accommodate the design steel. The strength factor and ductility factor are estimated using results of nonlinear static pushover analysis. It was observed that for seismic design category 'high' the strength factor has lesser contribution than ductility factor, whereas, opposite trend is observed for seismic design category 'low'. Further, the effects of staging height and tank capacity on strength and ductility factors for two different seismic design categories are studied. For both seismic design categories, the response reduction factors obtained from the nonlinear static analysis is higher than the code specified response reduction factors. The minimum dimension restriction of column is observed as key parameter in achieving the desired performance of the elevated water tank on frame staging.

• 한국재난정보학회 논문집
• /
• 제9권3호
• /
• pp.315-323
• /
• 2013

최근 건설 산업에서 FRP는 재료적 장점으로 RC 구조물의 보강 재료로서 많이 사용되어지고 있다. FRP 외부부착보강은 중량에 비하여 높은 강도 및 강성, 우수한 내구성과 시공성등 여러 가지 장점을 가지는 공법이다. 그러나 외부부착보강은 구조물이 투수성이 낮은 보강재로 밀폐되고 수분이 외부로 배출되지 못함으로 인하여, 장기적인 구조물의 손상을 발생시키는 문제점이 있다. 본 연구에서는 기존의 FRP (Fiber Reinforced Polymer)와 재료적성질은 동등하면서, 투수성을 지녀 콘크리트 구조물의 모체와 부착성 및 내구성능 및 내구성이 우수한 유리섬유 패널(Glass Fiber Composite Pannel )에 대해서 휨 실험을 수행하여 복합소재 스트립의 섬유함량의 변화에 따른 실험변수별 내력증진 및 연성 증진 효과를 비교 분석하였다.

• Wind and Structures
• /
• 제27권5호
• /
• pp.325-336
• /
• 2018

The physical infrastructure of the power systems, including the high-voltage transmission towers and lines as well as the poles and wires for power distribution at a lower voltage level, is critical for the resilience of the community since the failures or nonfunctioning of these structures could introduce large area power outages under the extreme weather events. In the current engineering practices, single circuit lattice steel towers linked by transmission lines are widely used to form power transmission systems. After years of service and continues interactions with natural and built environment, progressive damages accumulate at various structural details and could gradually change the structural performance. This study is to evaluate the typical existing transmission tower-line system subjected to synoptic winds (atmospheric boundary layer winds). Effects from the possible corrosion penetration on the structural members of the transmission towers and the aerodynamic damping force on the conductors are evaluated. However, corrosion in connections is not included. Meanwhile, corrosion on the structural members is assumed to be evenly distributed. Wind loads are calculated based on the codes used for synoptic winds and the wind tunnel experiments were carried out to obtain the drag coefficients for different panels of the transmission towers as well as for the transmission lines. Sensitivity analysis is carried out based upon the incremental dynamic analysis (IDA) to evaluate the structural capacity of the transmission tower-line system for different corrosion and loading conditions. Meanwhile, extreme value analysis is also performed to further estimate the short-term extreme response of the transmission tower-line system.

• Journal of Welding and Joining
• /
• 제30권3호
• /
• pp.66-70
• /
• 2012

Welding is an essential process in the automotive industry. Most welding processes that are used for auto body is spot welding. And $CO_2$ arc welding is used in a small part. In production field, $CO_2$ arc welding process is decreased and spot welding process is increased due to welding quality is poor and defects are occurred in $CO_2$ arc welding process frequently. But $CO_2$ arc welding process should be used at robot interference parts and closed parts where spot welding couldn't. $CO_2$ welding is divided into lap welding and plug arc spot welding. In case of plug arc spot welding, burn through and under fill were caused in various welding environment such as different thickness combinations of base metal, teaching point, over the two steps welding and inconsistent voltage/current. It makes some problem like poor quality of welding area and decrease the productivity. In this study, we will evaluate the effect of teaching point through the weld pool behavior and bead geometry in the arc spot welding at the plut hole. Welding position is horizontal position. And galvanized steel sheet of 2.0mm thickness that has plug hole of 6mm diameter was used. Teaching point was changed by center, top, bottom, left and right of the plug hole. At each condition, the phenomenon of weld pool behavior was confirmed using a high-speed camera. As the result, we find the center of plug hole is the most optimal teaching point. In the other teaching point, under fill was occurred at the plug hole. This phenomenon is caused by gravity and surface tension. For performance of arc spot welding at the plug hole, the teaching condition should be controlled at a center of plug hole.

• 한국군사과학기술학회지
• /
• 제22권5호
• /
• pp.599-606
• /
• 2019

The Arena Fragmentation Test(AFT) is one of the important tasks for designing a high-explosive warhead. In order to measure the statistics of a warhead in the test, fragments of a warhead that penetrate steel plates are detected by using complex and expensive measuring equipment. In this paper, instead of using specific hardware to measure the statistics of a warhead, we propose to use an image processing based object detection algorithm to detect fragments in AFT. To this end, we use a hard-thresholding method with a brightness feature and apply a morphology filter to remove noise components. We also propose a simple yet effective temporal filtering method to detect only the first penetrating fragments. We show that the performance of the proposed method is comparable to that of a hardware system under the same experimental conditions. Furthermore, the proposed method can produce better results in terms of finding exact positions of fragments.

• Nuclear Engineering and Technology
• /
• 제34권1호
• /
• pp.42-59
• /
• 2002

In order to transmute long-lived radioactive nuclides such as transuranics(TRU), Tc-99, and I- l29 in LWR spent fuel, a preliminary conceptual design study has been performed for the accelerator driven subcritical reactor system, called HYPER(Hybrid Power Extraction Reactor) The core has a hybrid neutron energy spectrum: fast and thermal neutrons for the transmutation of TRU and fission products, respectively. TRU is loaded into the HYPER core as a TRU-Zr metal form because a metal type fuel has very good compatibility with the pyre- chemical process which retains the self-protection of transuranics at all times. On the other hand, Tc-99 and I-129 are loaded as pure technetium metal and sodium iodide, respectively. Pb-Bi is chosen as a primary coolant because Pb-Bi can be a good spallation target and produce a very hard neutron energy spectrum. As a result, the HYPER system does not have any independent spallation target system. 9Cr-2WVTa is used as a window material because an advanced ferritic/martensitic steel is known to have a good performance under a highly corrosive and radiation environment. The support ratios of the HYPER system are about 4∼5 for TRU, Tc-99, and I-129. Therefore, a radiologically clean nuclear power, i.e. zero net production of TRU, Tc-99 and I-129 can be achieved by combining 4 ∼5 LWRs with one HYPER system. In addition, the HYPER system, having good proliferation resistance and high nuclear waste transmutation capability, is believed to provide a breakthrough to the spent fuel problems the nuclear industry is faced with.

• 대한조선학회논문집
• /
• 제58권5호
• /
• pp.294-302
• /
• 2021

In this study, the 3D printing technique called design for additive manufacturing (DfAM) that is widely used in various industries was applied to marine leisure ships of equipment. The DfAM for the stanchion for crew safety was applied to the equipment used in an actual recreational craft. As design constraints, the design alternatives were not to exceed the safety and weight of the existing stainless steel material, which were reviewed, and the production of a low-cost FFF-type 3D printing method that can be used even in small shipyards was considered. Until now, additive manufacturing has been used for manufacturing only prototypes owing to its limitations of high manufacturing cost and low strength; however, in this study, it was applied to the mass production process to replace existing products. Thus, a design was developed with low manufacturing cost, adequate performance maintenance, and increased design freedom, and the optimal design was derived via structural analysis comparisons for each design alternative. In addition, a life-cycle assessment based on the ISO 1404X was conducted to develop sustainable products. Through this study, the effectiveness of additive manufacturing was examined for future applications in the shipbuilding industry.

• Earthquakes and Structures
• /
• 제20권1호
• /
• pp.109-122
• /
• 2021

Significant progress in the oil and gas industry advances the application of pipeline into an intelligent era, which poses rigorous requirements on pipeline safety, reliability, and maintainability, especially when crossing seismic zones. In general, strike-slip faults are prone to induce large deformation leading to local buckling and global rupture eventually. To evaluate the performance and safety of pipelines in this situation, numerical simulations are proved to be a relatively accurate and reliable technique based on the built-in physical models and advanced grid technology. However, the computational cost is prohibitive, so one has to wait for a long time to attain a calculation result for complex large-scale pipelines. In this manuscript, an efficient and accurate surrogate model based on machine learning is proposed for strain demand prediction of buried X80 pipelines subjected to strike-slip faults. Specifically, the support vector regression model serves as a surrogate model to learn the high-dimensional nonlinear relationship which maps multiple input variables, including pipe geometries, internal pressures, and strike-slip displacements, to output variables (namely tensile strains and compressive strains). The effectiveness and efficiency of the proposed method are validated by numerical studies considering different effects caused by structural sizes, internal pressure, and strike-slip movements.

• 한국산학기술학회논문지
• /
• 제22권3호
• /
• pp.88-93
• /
• 2021

선박의 건조과정이나 압력용기의 몸체 부분을 용접할 경우 많이 사용되는 SAW(Submerged Arc Welding)는, 용접 부위에 분말 형태의 용제(Flux)를 일정 두께로 살포하고 그 속에 전극 와이어를 연속적으로 공급하여 용접이 이루어지는 방법으로 용접 시 발생되는 아크열이 외부로 노출되지 않는 특징이 있으며, 잠호용접으로 불리기도 한다. 또한 1,500~3,000A의 전류까지 통전 할 수 있는 고전류 용접이 가능하며 아크효율이 95% 이상, 미세한 금속 산화물 입자인 Welding Fume 발생량이 적고 아크광선이 외부로 노출되지 않아 청정한 작업이 가능하며 용입이 깊고 결함이 잘 발생하지 않아 용접 이음부의 신뢰도가 높다. 본 연구에서는 SM490C-TMC 후판을 서브머지드 아크용접(SAW)을 이용하여 이종 용접한 후 용접부의 기계적 특성을 인장, 경도, 매크로, 자분탐상 검사 결과를 분석하여 다음과 같은 결론을 도출하였다. 굽힘 시험 결과 시료에서 표면의 터짐 현장이 발생하지 않았고 기타 결점의 유무를 확인할 수 없었으며, 이는 용접 이후 소성변형 과정에서도 충분한 인성을 발휘하고 있는 것으로 나타났으며, 1F 용접 방법이 굽힘 성능에 문제가 없는 것으로 판단되었다.