• Journal of Power Electronics
• /
• 제18권1호
• /
• pp.23-33
• /
• 2018

Silicon Carbide (SiC) MOSFET belongs to the family of wide-band gap devices with inherit property of low switching and conduction losses. The stable operation of SiC MOSFET at higher operating temperatures has invoked the interest of researchers in terms of its application to high power density (HPD) power converters. This paper presents a performance study of SiC MOSFET based two-phase interleaved boost converter (IBC) for regulation of avionics bus voltage in more electric aircraft (MEA). A 450W HPD, IBC has been developed for study, which delivers 28V output voltage when supplied by 24V battery. A gate driver design for SiC MOSFET is presented which ensures the operation of converter at 250kHz switching frequency, reduces the miller current and gate signal ringing. The peak current mode control (PCMC) has been employed for load voltage regulation. The efficiency of SiC MOSFET based IBC converter is compared against Si counterpart. Experimentally obtained efficiency results are presented to show that SiC MOSFET is the device of choice under a heavy load and high switching frequency operation.

• 대한전자공학회논문지SD
• /
• 제41권4호
• /
• pp.67-74
• /
• 2004

기존의 버스트 모드 자동전력제어 회로는 데이터 율이 증가함에 따라 마크밀도 변화 영향을 심하게 받아 에러를 야기하였다. 이 문제를 해결하기 위해 높은 데이터 율에서도 마크밀도의 영향을 배제시킬 수 있는 새로운 구조의 첨두 비교기를 고안하고 이를 자동전력제어 회로에 적용하여 마크밀도 변화에 강한 버스트 모드 자동전력제어 회로를 제안하였다. 제안한 자동전력제어 회로 내의 첨두 비교기는 높은 데이터 율에서 뿐만 아니라 광범위한 기준전류 및 차 전류 변화에서도 미소한 마크밀도 변화 영향만을 보여 마크밀도 변화에 매우 강한 특성을 확인 할 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제27권2호
• /
• pp.104-109
• /
• 2014

To operate organic light emitting device (OLED) with alternating current (AC) power source without AC/DC(direct current) converter, we fabricated the fluorescent OLED and measured the emission characteristics with AC and DC. The OLED operated by AC showed higher maximum current efficiency of 8.2 cd/A and maximum power efficiency of 8.3 lm/W. But current efficiency and power efficiency of AC driven OLED showed worse than DC driven OLED at high voltage above 10 V. This result can be explained by the peak voltage of AC was $\sqrt{2}$ times than DC, In case of low driving voltage the emission characteristics were improved by the peak voltage of AC, but in case of high driving voltage the emission efficiencies were decreased by the roll off phenomena. Finally, serial OLED arrays using twelve OLEDs driven by AC 110 V showed average voltage of 9.17 V, voltage uniformity of 99.0%, average luminance of $1,175cd/m^2$, luminance uniformity of 94.4%.

• Journal of Power Electronics
• /
• 제17권2호
• /
• pp.315-322
• /
• 2017

LED is a promising new generation of green lighting with the advantages of high efficiency, good optical performance, long lifetime and environmental friendliness. A pulsating current can be used to drive LEDs. However, current with a high peak-to-average ratio is unfavorable for LEDs. A novel control scheme for the ac-dc critical conduction mode (CRM) flyback LED driver is proposed in this paper. By using the input voltage, output voltage and average output current to control the turn-on time of the switch, the peak-to-average ratio of the output current can be reduced. The operation principle is analyzed and an implementation circuit is put forward. Experimental results show the effectiveness of the proposed scheme.

• 전기학회논문지
• /
• 제66권1호
• /
• pp.61-65
• /
• 2017

In this paper a prototype of high frequency heating power supply system based on the high frequency heating principle is designed to take the place of acupuncture, moxibustion, warm dressing treatment and some other traditional physical therapy methods. Which possess the advantages of low cost, convenient, easy operation and good effect. The high frequency heating power supply can generate a pulse voltage of more than 1KV with 300KHz switching frequency to heat the patient's skin. The skin temperature can reach to $41{\sim}42^{\circ}C$. The peak current control method is used to maintain the skin temperature in the designed range. The design of the main circuit is based on the flyback converter topology. An easier and practical design method is proposed in this paper. The power supply system prototype is verified to be stable and reliable by both the simulation and experimental results.

• Journal of Power Electronics
• /
• 제13권5호
• /
• pp.746-756
• /
• 2013

The modularized subunit of an electronic power transformer (EPT) is a series connection of two H-bridge voltage-source converters and a DC-DC converter with a high-frequency isolation transformer (HFIT). On the basis of cascading and paralleling the modularized subunits, EPT can be used in high-voltage and large-current applications in the power system. This paper discusses the steady state analysis of the modularized subunit of EPT. Theoretical analysis considers the influences of the two H-bridge voltage-source converters on the two sides of the DC-DC converter. We deduce the formulas of the theoretical calculation on the internal electrical characteristics of EPT (e.g., the voltages of the DC-bus capacitor and the primary side peak current of the HFIT). This paper provides guidance on the design and selection of EPT key elements (e.g., the DC-bus capacitors and HFIT). Experimental results are obtained from a single subunit of a laboratory model rated at 962 V, 15 kVA. All calculations, simulations, and experiments confirm the theoretical analysis of the subunit of EPT.

• 한국산업융합학회 논문집
• /
• 제21권5호
• /
• pp.207-217
• /
• 2018

Recently, the importance of energy demand management, particularly peak load control, has been increasing due to the policy changes of the Second Energy Basic Plan. Even though the installation of distributed generation systems such as Photovoltaic and energy storage systems (ESS) are encouraged, high initial installation costs make it difficult to expand their supply. In this study, the power consumption of a university building was measured in real time and the measured power consumption data was used to calculate the optimal installation capacity of the Photovoltaic and ESS, respectively. In order to calculate the optimal capacity, it is necessary to analyze the operation methods of the Photovoltaic and ESS while considering the KEPCO electricity billing system, power consumption patterns of the building, installation costs of the Photovoltaic and ESS, estimated savings on electric charges, and life time. In this study, the power consumption of the university building with a daily power consumption of approximately 200kWh and a peak power of approximately 20kW was measured per minute. An economic analysis conducted using these measured data showed that the optimal capacity was approximately 30kW for Photovoltaic and approximately 7kWh for ESS.

• Journal of Welding and Joining
• /
• 제9권1호
• /
• pp.32-39
• /
• 1991

A 200W pulsed Nd: YAG laser for fine welding was developed. The important laser parameters such as laser peak power, average power, pulse width, and pulse energy for welding were studied. In order to obtain the sufficient laser power density for welding, thermal lensing effects were analyzed and a laser resonator with laser beam divergence was designed. The power supply unit was designed to support up to 7kW input. The pulse control unit was developed using a GTO thyristor and could control over 100kW input power to obtain 3.5kW peak power laser. Also due to the GTO thyristor the pulse width could be varied continuously from 0.1 to 20 msec and maximum repetition rate was as high as 300pps.

• 한국응용과학기술학회지
• /
• 제37권1호
• /
• pp.17-27
• /
• 2020

본 연구는 6주간의 고강도 복합 훈련 프로그램을 통해 카누 선수의 심폐기능(Cardiorespiratory Function), 체간 등속성 근력(Isokinetic Trunk Strength) 그리고 무산소성 파워(Anaerobic Power)에 미치는 영향을 확인하는데 있다. 이를 위해 고등학교 카누 선수 9명을 대상으로 고강도 복합 훈련 프로그램을 적용하였으며, 고강도 훈련 프로그램은 주 2회의 유산소 운동(화, 목), 주 3회의 무산소 운동(월, 수, 금) 그리고 주 5회의 유연성 운동을 실시하였다. 고강도 복합 훈련 프로그램의 핵심은 무산소성 훈련 프로그램으로 기존 1RM의 퍼센트(%)를 나누어 훈련하던 방식과는 달리 횟수에 대한 100%의 중량을 가지고 하는 훈련이며, 유산소성 운동과 짐볼운동은 보조적인 개념으로 실시하였다. 연구결과, 고강도 복합 훈련 프로그램에 따른 신체구성에서 신장과 근육량은 통계적으로 의한 차이가 있었으며, 체중, 체지방율, BMI는 통계적으로 유의한 차이는 없는 것으로 나타났다. 심폐기능의 경우, 최대산소섭취량과 총 운동시간은 통계적으로 유의한 차이가 있는 것으로 나타났다. 체간 등속성 근력의 경우, 각속도 30°/sec에서는 Flexors 운동시 Peak Torque 항목에서만 통계적으로 유의한 차이가 있는 것으로 나타났다. 각속도 120°/sec에서는 Extensors 운동시 Total Work 항목에서만 통계적으로 유의한 차이가 있는 것으로 나타났다. 무산소성 파워의 경우, Peak Power, Average Power, Peak Drop의 모든 항목에서 통계적으로 유의한 차이가 없는 것으로 나타났다. 이상의 결과를 종합해보면 심폐기능에서는 유의한 개선효과가 있었지만 체간 등속성 근력과 무산소성 파워 항목에서 증가하는 경향은 있었지만 통계적인 차이는 없는 것으로 나타났다. 결론적으로 선수 개개인의 근력과 파워가 개선되는 경향이 나타난 것을 고려하면 훈련기간을 6주 이상으로 구성하고 사례수가 보강된다면 체계적인 결과를 얻을 수 있을 것으로 생각된다. 본 연구에서 적용한 고강도 복합 훈련 프로그램은 카누 선수들의 경기력 향상 효과를 기대할 수 있는 훈련 프로그램으로 적용될 수 있을 것으로 판단된다.

• 정보처리학회논문지C
• /
• 제12C권6호
• /
• pp.901-906
• /
• 2005

본 논문에서는 초고속 전승을 위해 제안된 HCOC(High Capacity Orthogonal Code) 대역확산(Spread Spectrum) 시스템의 높은 PAPR(Peak power to Average Power Ratio)을 줄여주는 새로운 MHCOC (Mapped HCOC) 대역확산 기술을 제안하고, 같은 비트 수를 전송할 수 있는 기존의 MQAM 대역확산 시스템과 비교 분석한다. 또한 전송 채널의 상황에 따라 알맞은 데이터 서비스를 하는 QoS (Quality of Service)를 만족시키기 위해 제안한 시스템의 적응성에 대하여 연구한다. 컴퓨터 시뮬레이션을 통하여 제안한 시스템의 성능을 평가 및 분석하고, 기존의 시스템과 비교 분석한다.