• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.15 no.7
• /
• pp.581-601
• /
• 1990

A variety of method to diagnose the fault of rotational mechine is suggested, the latest data. This paper uses Bispectrum which is sort of high order spectrum, diagnose the ball bearing of the rotational machine element. Apprehending the physical meaning of Bispectrum, computer simulation is performed. The result from computer simulation and the signal of the faulted ball bearing is studied from all it's aspects. It is found that the Bispectrum is more effective than the conventional Power Spectrum.

• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.98-101
• /
• 2002

The switching-mode power converter has been widely used because of its features of high efficiency and small weight and size. These features are brought by the ON-OFF operation of semiconductor switching devices. However, this switching operation causes the surge and EMI(Electromagnetic Interference) which deteriorate the reliability of the converter themselves and entire electronic systems. This problem on the surge and noise is one of the most serious difficulties in AC-to-DC converter. In the case of carrier frequency selection, output-voltage of steady state and transient state is fully regulated. A RPWM control method was proposed in order to smooth the switching noise spectrum and reduce it's level. Experimental results are verified by converter operating at 300V/1kW with 5%${\sim}$30% white noise input. Spectrum analysis is performed on the Phase current and the CM noise voltage. The former is measured with Current Probe and the latter is achieved with USN. which are connected to the spectrum analyzer respectively.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.46 no.3
• /
• pp.59-68
• /
• 2023

Currently, yellow phosphor of Y3Al5O12:Ce3+ (YAG:Ce) fluorescent material is applied to a 450~480nm blue LED light source to implement a white LED device and it has a simple structure, can obtain sufficient luminance, and is economical. However, in this method, in terms of spectrum analysis, it is difficult to mass-produce white LEDs having the same color coordinates due to color separation cause by the wide wavelength gap between blue and yellow band. There is a disadvantage that it is difficult to control optical properties such as color stability and color rendering. In addition, this method does not emit purple light in the range of 380 to 420nm, so it is white without purple color that can not implement the spectrum of the entire visible light spectrum as like sunlight. Because of this, it is difficult to implement a color rendering index(CRI) of 90 or higher, and natural light characteristics such as sunlight can not be expected. For this, need for a method of implementing sunlight with one LED by using a method of combining phosphors with one light source, rather than a method of combining red, blue, and yellow LEDs. Using this method, the characteristics of an artificial sunlight LED device with a spectrum similar to that of sunlight were demonstrated by implementing LED devices of various color temperatures with high color rendering by injecting phosphors into a 405nm deep blue LED light source. In order to find the spectrum closest to sunlight, different combinations of phosphors were repeatedly fabricated and tested. In addition, reliability and mass productivity were verified through temperature and humidity tests and ink penetration tests.

• Environmental Analysis Health and Toxicology
• /
• v.5 no.3_4
• /
• pp.1-17
• /
• 1990

In order to decide the priority of prevention activities in environmental pollution, a study must be carried out in the wide spectrum of causes and effects of pollution particularly effects on humanbeing in the concept of environmental engineering and toxicology Therefore, a study must be covered various segments of environment such as air, water/sea water, wastes and soil in other words sources of pollution should be analysed in the view point of intergrated efforts of engineering and toxicology to locate high priority of prevention activities which given the high value of human health.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2000.10a
• /
• pp.440-447
• /
• 2000

In order to evaluate the cost effectiveness of seismic isolation for bridges in low and moderate seismic region, a method of calculation minimum life-cycle cost of seismic-isolated bridges under specific acceleration level and soil condition is developed. Input ground motion is modeled as spectral density function compatible with response spectrum for combination of acceleration coefficient and site coefficient. Failure probability is calculated by spectrum analysis based on random vibration theories to simplify repetitive calculations in the minimization procedure. Ductility of piers and its effects on cost effectiveness are considered by stochastic linearization method. Cost function and cost effectiveness index are defined by taking into consideration the characteristics of seismic isolated bridges. Limit states for calculation of failure probability are defined on superstructure, isolator and pier, respectively. The results of example design and analysis show that seismic isolation is more cost-effective in low and moderate seismic region than in high seismic region.

• Ocean and Polar Research
• /
• v.38 no.4
• /
• pp.325-330
• /
• 2016

Partial high frequency bands were allocated to the operation of ocean surface radars that monitor the sea surface currents and waves in WRC-12. On that basis, government-related organizations revised the table of domestic frequency allocation. In order to study radio environments in the allocated bands for ocean radar, tests of the radio signal spectrum were carried at 7-sites using the receiver of the ocean surface radar system operated with a shutdown of the transmitter for 10-60 min. The results showed that no serious radio noises occur at 25 and 43 MHz bands, indicating a good radio environment for the ocean surface radar operation. However, at 13 MHz band, it was difficult to generate stable and confidential data from the ocean surface radar because serious radio noises occurred continuously.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.257-259
• /
• 2008

Acceleration time history (ATH) used in the seismic analysis should envelop a target power spectral density (PSD) function in addition to the design response spectrum in order to have sufficient energy at each frequency for the purpose of ensuring adequate load. Even though design regulations require the ATH used in seismic analysis to meet a target PSD function, the reason that ATHs meet to a target PSD function is not described. Thus, artificial ATHs for high PSD function and artificial ATHs for low PSD function are generated. And then elastic and inelastic single-degree-of-freedom (SDOF) systems are loaded with these artificial time histories as the earthquake load. As a result, linear response and inelastic response of SDOF systems are affected by PSD function.

• Journal of the Korean Society of Radiology
• /
• v.14 no.7
• /
• pp.849-856
• /
• 2020

In the gamma-ray energy spectrum study, nuclide analysis through energy analysis is very important. High-purity Ge detectors, which are commonly used for gamma-ray energy measurements, are commonly used because of their high energy resolution and relatively high detection efficiency. However, in order to maintain a high energy resolution, the semiconductor detector has a problem in that it is difficult to maintain the original performance if the noise generated from the surrounding environment is not effectively blocked, and the effect of the expensive device is not achieved. Therefore, in this study, ground loop isolator (NEXT-001HDGL) was used to remove the electrical noise generated from the detector. In order to test the effect of improving energy resolution, HPGe detection device newly installed in the proton accelerator KOMAC was used. In the case of gamma-ray energy 2614 keV, the energy resolution was improved from (0.16 ± 0.02) % to (0.11 ± 0.01) %, and in the case of gamma-ray energy 662 keV of 137Cs isotope, the energy resolution was improved from (0.72 ± 0.07) % to (0.27 ± 0.03) %. This result is considered to be very useful for the gamma ray spectrum study using the HPGe detection equipment of KOMAC(Korea Multi-Purpose Accelerator Complex).

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1991.04a
• /
• pp.150-157
• /
• 1991

As the system monitoring technology become required in order to imporve the system performance and the productivity, We've studied to the detection for the tool breakage using AE sensor that is able to detection of generated high frequency strss pulse at cutting. The method of spectrum analysis are used for analysis of AE signals in detection system. The experiments are carred out in a CNC lathe.

• Steel and Composite Structures
• /
• v.48 no.5
• /
• pp.499-505
• /
• 2023

Geological hazards in landslide is one of the most extensive and destructive phenomena are among natural disasters. According to the topography high mountains, tectonic activity, high seismicity, diverse conditions Geology and climate, basically China to create a wide spectrum of landslides have natural conditions and these landslides are annual. They cause a lot of financial losses to the country. It is very difficult to predict the time of the landslide, hence the identification landslide sensitive areas and zoning of these areas based on the potential risk is very important. Therefore, it should be susceptible areas landslides should be identified in order to reduce damages caused by landslides find. the main purpose of landslide sensitivity analysis is identification high-risk areas and as a result, reducing damages caused by landslides It is the way of appropriate actions.