• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.8
• /
• pp.45-51
• /
• 2008

HID(High Intensity Discharge) search lamp for shipment requires a high open circuit and output current compare than vehicle. This paper presents a soft-start open circuit voltage and constant current sequence control method for 2.5[kW] HID search lamp. The proposed method controls the opal circuit voltage and discharge current of HID lamp according to ignition signal with a simple 8-bit micro-processor and PWM device. For the stable control of lamp, micro-processor checks the output voltage and current. And the checked signals are compared with ignition signal and changes the control mode for stable operation. An ignition signal and micro-processor change the control mode from open circuit voltage contort to constant current control. The proposed control scheme is verified from experimental tests of 2.5[kW] HID search lamp for shipment.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.858-864
• /
• 2017

This study aims to restrain free conducting wire-type particles which are commonly and dangerously existing within DC gas-insulated transmission lines. A realistic platform of a coaxial cylindrical electrode was established by using a high-speed camera and a partial discharge (PD) monitor to observe the motion, PD, and breakdown of these particles. The probabilities of standing or bouncing, which can be affected by the length of the particles, were also quantitatively examined. The corona images of the particles were recorded, and particle-triggered PD signals were monitored and extracted. Breakdown images were also obtained. The air-gap breakdown with the particles was subjected to mechanism analysis on the basis of stream theory. Results reveal that the lifting voltage of the wire particles is almost irrelevant to their length but is proportional to the square root of their radius. Short particles correspond to high bouncing probability. The intensity and frequency of PD and the micro-discharge gap increase as the length of the particles increases. The breakdown voltage decreases as the length of the particles decreases.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.11
• /
• pp.1049-1054
• /
• 1998

The LiCo$O_2$ powder was synthesized by a solution phase reaction. This shows a high (003) peak intensity and low (104) or (101) peak intensities in X-ray diffraction spectra. The LiCo$O_2$/Li cell shows an initial discharge capacity of 102.9mAh/g and an average discharge potential or 3.877V at a current density of 50mA/g between 3.0~4.2V. The peaks of dQ/dV plot are associated with Li ion intercalation/deintercalation reaction. To evaluate the cycleability of an actual battery system, cylindrical lithium ion cell was manufactured using graphitized MPCF anode and LiCoO$_2$ cathode. After 100th cycle, this cel maintains 80% capacity of 10th cycle value. The LiCoO$_2$/MPCF cell has a high discharge voltage of 3.6~3.7V and a good cycle life performance on cycling between 4.2~2.7V.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.74-74
• /
• 2010

The aqua-plasma is the non-thermal plasma in electrical conductive electrolyte by generates the vapor film layer on the immersed metal electrode surface. This plasma can generate the hydroxyl radical by dissociate the water molecule with the plasma electron. To develop the plasma discharge device for high efficiency in the hydroxyl radical generation, proper model for estimation of plasma power is necessary. In this work, the 1-D spherical model was developed, considering temperature dependence material constants. The relation between the plasma power and hydroxyl generation was also studied by the comparison between the optical emission intensity from the hydroxyl radical using monochromator and estimated plasma power. First, the thickness of vapor layer thickness was estimated using the Navier-Stokes fluid equation in order to calculate the discharge E-field inside vapor layer. Using the E-field magnitude and power balance on the plasma generation, it was possible to estimate the plasma power. The plasma power was assumed to uniformly fill the vapor layer and the temperature of vapor layer was fixed in the boiling temperature of electrolyte, 375K. In the experiment, the aqua-plasma was discharged in the saline by applied the voltage on the bipolar electrode. The range of applied voltage was 234 to 280V-rms in the frequency of 380 kHz. Two type electrodes were produced with two ${\Phi}0.2$ tungsten. The plasma power was estimated from the V-I signal from the two high voltage probes and current probe. The estimated plasma power agreed with the profile of emission intensity when the plasma discharged between the metal electrode and vapor layer surface. However, when the plasma discharged between the metal electrodes, the increasing rate of emission intensity was lower than the increase of plasma power. It implies that the surface reaction is more sufficient rather than the volume reaction in the radical generation, due to the high density of water molecule in the liquid.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.219-223
• /
• 2001

In this paper, electromagnetic waves were measured in accordance with propagating the discharge when positive and negative DC high voltage was applied to needle-plane electrdes and plane-plane electrdes that solid dielectric was inserted between the electrodes. The radiated electromagnetic waves were investigated in bandwidth of VHF($30{\sim}230$[MHz]) using an biconical antenna. In needle-plane electrodes high electric field intensity is shown in both frequency band of 90(MHz) and 170[MHz], and gradually decreasing characteric is appeared at high frequency band. However high electric field intensity is shown in both 80[MHz] and 140[MHz] in case of plane-plane electrodes configuration. And over 150[MHz] frequency band, rapidly decreasing characteristic is shown. Moreover, electric field intensity of positive DC is about $5{\sim}10$[dB] higher than negative DC.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.320-323
• /
• 2007

The vacuum sealing method is adopted to minimize the residual impurity gas by enhancing a base vacuum level, and the resultant changes in the reset, address, and sustain discharge characteristics, such as a firing voltage, IR emission, and ICCD image, were examined in comparison with the conventional sealing method in the 42-in. AC-PDP. In the PDP cells fabricated by the vacuum sealing method, the ICCD observation illustrates that the discharge is initiated and extinguished very fast and its IR emission intensity is high.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.5
• /
• pp.982-988
• /
• 2009

In a surface type ac PDP having $200{\mu}m$ gap between the surface electrodes, the luminous efficacy has a reciprocal dependence on the sustaining frequency. The discharge current flowing to the address electrodes are measured to investigate the phenomena and spectral intensity from visible light to infra red is measured to verify phosphor saturation with the frequency. Experiments show the discharge between the address and surface electrodes deteriorates the efficacy in high sustaining frequencies. Pulse width modulation is introduced to improve the efficacy. In optimum conditions, we obtained 1.99lm/w and 1.79lm/w at 200kHz and 250kHz, respectively.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.3
• /
• pp.373-378
• /
• 2007

Soft switching was applied to the multi-level inverter to enhance the performance of the high-intensity discharge (HID) ballast used in vehicle headlights. The electrical properties were investigated and the available modeling of ballast in steady state was calculated using mathematical methods. The result was used in analyzing the power characteristics. The modeling was confirmed by the experiment.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.602-604
• /
• 2001

본 논문은 고압방전(HID)램프용 안정기의 효율을 향상시키기 위하여 자기식 안정기의 코아 및 코일의 권회수에 따른 특성을 분석하고 이를 바탕으로 코아를 설계하는 것이다. 코아의 재질 및 형상에 따른 자속분포를 자계해석 프로그램으로 해석하여, 기존 제품안정기 효율 90%에 비해 향상시킬수 있는 기초배경 및 설계 방안을 제시하였다.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.595-598
• /
• 1999

A new of the automotive High Intensity Discharge(HID) lamp ballast systems is proposed. Proposed scheme is consisted of the high frequency DC-DC converter and low frequency DC-AC inverter as same as conventional HID ballast system. But this system separates ignition voltage from dc link voltage, which results to used the lower voltage rating power devices for HID lamp ballast system compared with conventional system. As a result, proposed system has a lower cost and higher efficiency.