• 대한토목학회논문집
• /
• 제4권2호
• /
• pp.133-142
• /
• 1984

횡방향(橫方向)과 종방향(縱方向), 대입열용접(大入熱鎔接)과 소입열용접(小入熱鎔接), 모재(母材)와 같은 강도(强度)의 용접재료(鎔接材料) 사용(使用)과 모재(母材)보다 낮은 강도(强度)의 용접재료(鎔接材料) 사용(使用) 등으로 서로 비교되는 용접(鎔接)이음의 소인장시험편(小引張試驗片)을 만들어서 피로시험(疲勞試驗)을 행하여 피로구열(疲勞龜裂) 진전속도(進展速度) ${\frac{da}{dN}}$와 구열선단(龜裂先端) 부근의 응력확대계수(應力擴大係數)의 변동범위(變動範圍) ${\Delta}K$와의 관계곡선(關係曲線)을 그려서 비교시험간(比較試驗間)의 모재(母材), 열영향부(熱影響部) 및 용착금속부(鎔着金屬部)로 구분, 혹은 지금까지의 연구자료(硏究資料) 등과 비교검토하였다. 이 결과, 다음과 같은 현상들을 알 수 있었다. 기본적(基本的)으로, 용접방향(鎔接方向), 용접입열량(鎔接入熱量), 용접재료(鎔接材料)의 강도(强度), 혹은 모재(母材), 열영향부(熱影響部) 및 용착금속부(鎔着金屬部)의 구분 등에 따라 ${\frac{da}{dN}}-{\Delta}K$관계에 큰 차이가 없었다. 다만, 첫째, 소재(素材)에 대한 경우에 비해 대개 처음은 같은 ${\Delta}K$에서 ${\frac{da}{dN}}$가 상당히 늦다가 점차 증가하여 중간쯤에서 같아진 후 끝 부분에서 같은 ${\Delta}K$에서${\frac{da}{dN}}$가 다소 빨라짐을 알 수 있었다. 둘째, 열영향부(熱影響部)에서 용접금속부(鎔接金屬部)로 진전(進展)하면서 ${\frac{da}{dN}}$가 다소 늦어지는 것을 알 수 있었다. 셋째, 용접방향(鎔接方向)과 구열방향(龜裂方向)이 평행인 경우가 직각인 경우에 비해, 모재(母材)와 같은 용접재료(鎔接材料)를 쓴 경우 소입열용접(小入熱鎔接)인 경우가 대입열용접(大入熱鎔接)인 경우에 비해, 모재(母材)보다 낮은 용접재료(鎔接材料)를 쓴 경우 대입열용접(大入熱鎔接)인 경우가 소입열용접(小入熱鎔接)인 경우에 비해, 대입열(大入熱)의 평행용접(鎔接)의 경우를 제외한 모든 용접(鎔接)에서 모재(母材)와 같은 강도(强度)의 용접재료(鎔接材料)를 쓴 경우가 모재(母材)보다 낮은 강도(强度)의 용접재료(鎔接材料)를 쓴 경우에 비해 ${\Delta}K$가 낮은 시기(時期)에 일찍 저속(低速)으로 구열(龜裂)이 시작되어 ${\Delta}K$의 큰 증가없이 ${\frac{da}{dN}}$가 빠르게 증가한 다음 다른 경우와 같은 성상(性狀)으로 진전됨을 알 수 있었다. 넷째, 소입열용접(小入熱鎔接)의 경우 평행용접(鎔接)이 직각용접(鎔接)에 비해, 소입열용접(小入熱鎔接)이 대입열용접(大入熱鎔接)에 비해 같은 ${\Delta}K$에서 ${\frac{da}{dN}}$가 다소 늦은 것을 알 수 있었다.

• 전력전자학회논문지
• /
• 제27권2호
• /
• pp.85-91
• /
• 2022

This study proposes a high efficiency bridgeless Power Factor Correction (PFC) converter with improved common mode noise characteristics. Conventional PFC has limitations due to low efficiency and enlarged heat sink from considerable conduction loss of bridge diode. By applying a Common Mode (CM) coupled inductor, the proposed bridgeless PFC converter generates less conduction loss as only a small magnetizing current of the CM coupled inductor flows through the input diode, thereby reducing or removing heat sink. The input diode is alternately conducted every half cycle of 60 Hz AC input voltage while a negative node of AC input voltage is always connected to the ground, thus improving common mode noise characteristics. With the aim to improve switching loss and reverse recovery of output diode, the proposed circuit employs Critical Conduction Mode (CrM) operation and it features a simple Zero Current Detection (ZCD) circuit for the CrM. In addition, the input current sensing is possible with the shunt resistor instead of the expensive current sensor. Experimental results through 480 W prototype are presented to verify the validity of the proposed circuit.

• 한국환경과학회지
• /
• 제25권7호
• /
• pp.951-961
• /
• 2016

To prevent increasing instances of heat-related illnesses due to heat waves generated by climate change, a customized thermal environment index should be developed for outdoor workers. In this study, we conducted sensitivity analysis of the Masan harbor during a heat wave period (August 9th to 15th, 2013) using the MENEX model with metabolic rate and clothing-insulation data, in order to obtain realistic information about the thermal environment. This study shows that accurate input data are essential to gather information for thermophysiological indices (PST, DhR, and OhR). PST is sensitive to clothing insulation as a function of clothing. OhR is more sensitive to clothing insulation during the day and to the metabolic rate at night. From these results, it appears that when exposed to high-temperature thermal environments in summer, wearing highly insulated clothing and getting enough rest (to lower the metabolic rate) can aid in preventing heat-related illnesses. Moreover, in the case of high-intensity harbor work, quantification of allowed working time (OhR) during heat waves is significant for human health sciences.

• Journal of Welding and Joining
• /
• 제34권1호
• /
• pp.7-20
• /
• 2016

A brief overview is given of the development of various structural steels and their welding application technology. Firstly, the general characteristics and welding performance of structural steels used in architecture and bridge are introduced. For safety against earthquakes or strong wind, and for highly efficient welding in high-rise building constructions, ultra high strength steel with tensile strength over 800 MPa or high HAZ toughness steel plates under high heat input welding have been developed. In particular, efficient welding technology ensuring high resistance to cold and hot cracking of ultra high strength steel is reviewed in the present paper. Secondly, various coated steels used mainly for outer part in construction are briefly discussed. Moreover, a major drawback of coated steel during welding operation, and several solutions to overcome such technical problem are proposed. It is hoped that this review paper can lead to significant academic contributions and provide readers interested in the structural steels with useful welding technology.

• 한국레이저가공학회지
• /
• 제13권4호
• /
• pp.1-6
• /
• 2010

Recently the use of ultra high strength steels (UHSS) in structural and safety component is rapidly increasing in the automotive industry. For example, 1.5GPa grade hot stamping with die-quenching of boron steel 22MnB5 could apply crash-resistant parts such as bumpers and pillars. The development of laser welding process of hot stamping steels, fundamental bead-on-plate welding and lap joint welding test were carried out using 3kW Nd:YAG laser. Local hardening & HAZ softening occurred in hot stamping steel as a result of metallurgical change caused by the welding heat input in the Nd:YAG laser welding process. The size of soft zones in the hot stamping steel was related to the welding heat input, being smaller at high speeds which generated a smaller heat input. Also in the case of lap joint design structure, same welded characteristics were shown. The HAZ softening degree was controlled to ensure the joint strength.

• 한국정밀공학회지
• /
• 제22권7호
• /
• pp.19-26
• /
• 2005

The objective of this study is to investigate the influence of process parameters, such as power of laser, cutting speed of laser and material thickness, on the practical cutting region and the kerfwidth fer the case of cutting of CSP IN sheet using high power Nd:YAC laser in continuous wave(CW) mode. In order to obtain the practical cutting region and the relationship between process parameters on the kerfwidth, several laser cutting experiments are carried out. The effective heat input is introduced to consider the influence of power and cutting speed of laser on the kerfwidth together. From the results of experiments, the allowable cutting region and the relationship between the effective heat input and kerfwidth fur the case of cutting of CSP 1N sheet using high power CW Nd:YAG laser have been obtained to improve the dimensionalaccuracyofthecutarea.

• Journal of Welding and Joining
• /
• 제31권5호
• /
• pp.15-19
• /
• 2013

In order to reduce a grand compute time in prediction of welding distortion and residual stress by 3D thermal elastic plastic analysis, idealization of welding that is methods to heat input simultaneously in all weld metal on the same welding direction is carried out on two weld joints(butt welding and fillet welding). Then, the accuracy of acquired results is investigated through the comparison of the high accuracy prediction results. The thermal conduction analysis results by idealization of welding, the temperature is raised accompany with beginning of heat input because all of weld metal is heated input at the same time. On the other side, the temperature witch predicted with high accuracy is raised at the moment heating source passes the measuring points. So, there is difference of time between idealization of welding and considering of moving heat source faithfully. However, temperature history by idealization of welding is well simulated a high accuracy prediction results.

• Journal of Welding and Joining
• /
• 제26권5호
• /
• pp.66-73
• /
• 2008

Welding work in pre-erection or erection stage of shipbuilding construction to be carried out in flat and vertical upward position mostly and Electrogas welding(EGW) is actively applied especially for vertical butt joint of thicker steel plate recently. In this study considered how to develope and improve mechanical properties of weld metal and HAZ in high heat input welding processes such as EGW and Electroslag welding(ESW) with its welding equipment in order to extend the application range to the longitudinal members and hatch coaming parts of container ship. Some components of welding system and parameters were modified to get the faster travel speed and reduce weld heat input, and also by adding additional filler rods or tubes increase the amount of deposited weld metal. With the test get some good date can apply to actual fabrication work and recommend items to manufacture welding materials make better. Above all things it's a fruition that to prepare the possibility of application of ESW to shipbuilding construction which fill up the gap of stoppage days of more than 20 years.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.64-64
• /
• 2009

The use of ultra high strength steels (UTSS) is a natural result with increasing the demands for the lightweight materials and developing an innovative steel technology. Recently it has been used a 1500MPa grade hot stamping steel as automobile bodies, reinforcement parts, and seat frame parts in the automotive industry. It is a quenchenable steel manufactured by hot stamping process. It is well known that UTSS welding has softening in the heat affected zone(HAZ). Because welding is a sort of process applying heat, it should change the heat treated features and degrade the strength. This study was performed to investigate the influence of the heat input on the softening of the HAZ in the GMAW process. Each experiment was compared with that in the conditions having a different current and voltage at a same heat input. In order to analysis characteristics of the HAZ, optical microscope was used to observe microstructure and vickers hardness tests were carried out across the welds. Applying low heat input means a fast cooling rate. It leads to high hardness in the HAZ. It is found that characteristics of the HAZ are determined by microstructure obtained by different cooling rate.

• 대한기계학회논문집A
• /
• 제40권12호
• /
• pp.1055-1060
• /
• 2016

레이저 용접은 고밀도 용접법 중에 하나로 기존 용접방법에 비해 적은 입열로 깊은 용입과 빠른 용접속도를 얻을 수 있다. 연속 출력 파형 레이저 용접 시 입열량은 레이저 출력 및 용접속도에 의해 결정된다. 본 연구에서는 파이버 레이저를 사용하여 두께 0.5 mm의 순 티타늄 박판에 비드 및 겹치기 용접을 실시하였으며 레이저 출력 및 용접속도에 따른 용접성을 평가하였다. 레이저 출력 및 용접속도에 따른 용입깊이, 비드폭, 접합길이, 비드형상을 관찰하고 인장전단시험을 통해 기계적인 특성을 파악하였다. 실험결과, 겹치기 용접은 $P_L=0.5kW$, ${\nu}=2.5m/min$과 $P_L=1.5kW$, ${\nu}=6m/min$ 조건에서 양호한 접합길이를 가진 용접부를 얻을 수 있었으며, 용접부는 고출력보다 저출력 조건일 때 더 우수한 연성을 나타냈다.