• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.386-389
• /
• 2001

In this study, development of a new LTCC material using non-glassy system was attempted with respect to reducing the fabrication process steps and cost down. Lowering the sintering temperature can be achieved by liquid phase sintering. However, presence of liquid phases usually decrease dielectric properties, especially the quality factor. Therefore, the starting material must have quality factor as high as possible in microwave frequency range. And also, the material should have a low dielectric constant for enhancing the signal propagation speed. Regarding these factors, dielectric constants of various materials were estimated by the Clausius-Mosotti equation. Among them, ZnWO$_4$ was turned out the suitable LTCC material. ZnWO$_4$ can be sintered up to 98% of full density at 105$0^{\circ}C$ for 3 hours. It's measured dielectric constant, quality factor, and temperature coefficient of resonant frequency were 15.5, 74380GHz, and -70ppm/$^{\circ}C$, respectively In order to modify the dielectric properties and densification temperature, B$_2$O$_3$ and V$_2$O$_{5}$ were added to ZnWO$_4$. 40 mol% B$_2$O$_3$ addition reduced the dielectric constant from 15.5 to 12. And the temperature coefficient of resonant frequency was improved from -70 to -7.6ppm/$^{\circ}C$. However, sintering temperature did not change due to either lack of liquid phase or high viscosity of liquid phase. Incorporation of small amount of V$_2$O$_{5}$ in ZnWO$_4$-B$_2$O$_3$ system enhanced liquid phase sintering. 0.lwt% V$_2$O$_{5}$ addition to the 0.6ZnWO$_4$-0.4B$_2$O$_3$ system, reduced the sintering temperature down to 95$0^{\circ}C$ Dielectric constant, quality factor, and temperature coefficient of resonant frequency were 9.5, 16737GHz, and -21.6ppm/$^{\circ}C$ respectively.ively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.4
• /
• pp.348-351
• /
• 2007

Recently, Nanotechnology becomes a major issue in most part of industries. Nanotechnology is expected to develop various application products due to nano material mired composites is improved physical and electrical properties compared to conventional composites materials. Dielectric and insulation materials need to develop and improve like other field about nanotechnology. In this paper, we reported dielectric dispersion by size(no filler, $1.2{\mu}m$, 500 nm, 10 nm), frequencies(60, 120, 1 kHz), and temperatures($30{\sim}170^{\circ}C$). Dielectric constant of composites materials with filler shows higher than composites materials without filler and increased depending on rising temperatures in low frequency region. It was the effect that nano-filler and impurities in composites contributed to electrical conductivity. And dielectric properties depending on temperatures shows to change in low frequency region dramatically We analyzed interfacial polarization in low frequency region($10^{-2}$ Hz) and oriented polarization in high frequency region($10^{-5{\sim}6}$ Hz) on composites materials.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.642-645
• /
• 2002

Microwave dielectric properties of $ZnWO_4$ ceramic were investigated with calcination and sintering temperatures. The dielectric properties required for such application are high dielectric constant$(\varepsilon_r)$, high $Q{\times}f_o$ value and low temperature coefficient of resonant frequency$(\tau_f)$. These requirement correspond to necessities for size reduction, excellent frequency selectivity, good temperature stability of devices. $ZnWO_4$ ceramics could be sintered at low $1075^{\circ}C$, which was comparatively low temperature for microwave dielectrics. As a result, $ZnWO_4$ showed the dielectric constant of 13, quality factor($Q{\times}f_o$ value) of 22000 and 'temperature coefficient of resonant frequency$(\tau_f)$ of $-65{\pm}5ppm/^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.13 no.4
• /
• pp.259-265
• /
• 2003

For the aim of thin microwave absorbers used in mobile telecommunication frequency band, this study proposed a high permittivity dielectrics(λ/4 spacer) coated with ITO thin films of 377 $\Omega$/sq(impedance transformer). High frequency dielectric properties of ferroelectric ceramics, electrical properties of ITO thin films and microwave absorbing properties of ITO/dielectrics were investigated. Ferroelectric materials including $BaTiO_3$(BT), 0.9Pb($Mg_{1}$3/Nb$_{2}$3/)$O_3$-0.1 $PbTiO_3$(PMN-PT), 0.8 Pb (Mg$_{1}$3/$Nb_{2}$3/)$O_3$-0.2 Pb($Zn_{1}$3$_Nb{2}$3/)$O_3$(PMN-PZN) were prepared by ceramic processing for high permittivity dielectrics,. The ferroelectric materials show high dielectric constant and dielectric loss in the microwave frequency range. The microwave absorbance (at 2 ㎓) of BT, 0.9PMN-0.1PT, and 0.8PMN-0.2PZN were found to be 60%(at a thickness of 3.5 mm), 20% (2.5 mm), and 30% (2.5 mm), respectively. By coating the ITO thin films on the ferroelectric substrates with λ/4 thickness, the microwave absorbance is greatly improved. Particularly, when the surface resistance of ITO films is closed of 377 $\Omega$/sq, the reflection loss is reduced to -20 ㏈(99% absorbance). This is attributed to the wave impedance matching controlled by ITO thin films at a given thickness of high permittivity dielectrics of λ/4 (3.5 mm for BT, 2.5 mm for PMN-PT and PMN-PZN at 2 ㎓). It is, therefore, successfully proposed that the ITO/ferroelectric materials with controlled surface resistance and high dielectric constant can be useful as a thin microwave absorbers in mobile telecommunication frequency band.

• Electrical & Electronic Materials
• /
• v.7 no.3
• /
• pp.187-199
• /
• 1994

In order to find an effect of structural changes due to variation of addition ratio of anhydride hardener and postcuring herat-treatments upon electrical properties of epoxy composites, the dielectric properties over a frequency range from 30[Hz] to l[MHz] were investigated in the temperature range of 20-180[.deg. C]. From the dielectric properties, the a peaks related with glass-transition phenomena of epoxy network appeared near 130[.deg. C], the conduction loss in high temperature region above 150[.deg. C] due to thermal dissociation of hardener started off with the low frequency side and the .betha. peak concerned with contribution of movable unreacted terminal epoxy groups and curing agents in the glass states concurred with the high-frequency side below 20[.deg. C]. And an effect of an hydride hardener upon structural changes and of postcuring heat treatments upon structural stability in epoxy composites would be explained through the estimation of the distribution of relaxation times and the activation energy for a .alpha. peak according to the WLF equations.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.7
• /
• pp.715-719
• /
• 1997

In order to study the dielectric properties of the oriental lacquer films, three different films have been prepared differing purification and curing procedures. Dielectric properties were measured in the frequency range of 1 Hz to 105 Hz at various temperatures between - 50 ℃ and 150 ℃. The DEA using 1 Hz showed that glass transition and secondary relaxation temperatures of oriental lacquer film are very time dependent. In addition, the frequency-independent negative peak between 25 ℃ and 45 ℃ was observed, which could represent the formation of crosslink by laccase enzyme during heating. On the contrary, the high temperature cured film showed a hardly noticeable negative peak at the temperature range. The relationship between thermodynamic properties and chemical structures has been discussed based on the analysis of the dielectric relaxation behavior using the Cole-Cole plot and the dielectric relaxation intensity.

• Applied Science and Convergence Technology
• /
• v.24 no.6
• /
• pp.224-227
• /
• 2015

Ferroelectric $Pb_2(Sc,Nb)O_6$ were prepared under two different sintering conditions using the oxide mixing method and the electrical properties were measured. The sintering conditions were $1350^{\circ}C$ for 25 minutes and $1400^{\circ}C$ for 20 minutes. EDX spectroscopy and XRD were used to determine the crystalline characteristic of the $Pb_2(Sc,Nb)O_6$ compositions Pyrochlore phase showed about 2% in all $Pb_2(Sc,Nb)O_6$ specimens. It expands the growth of crystals in samples sintered at $1400^{\circ}C$ than $1350^{\circ}C$, but all samples were the optimal crystallization. The temperature and frequency dependence of the complex dielectric constant and admittance were measured to analyze the electrical properties. The high dielectric constant of the specimens reflects the good stoichiometry and crystallization. The maximum value of the dielectric constant in the two specimens treated with sintering at $1350^{\circ}C$ and $1400^{\circ}C$ were more than 27,000, and the dielectric loss at room temperature is smaller than 0.05. The maximum dielectric constant decreased with increasing frequency, the transition temperature also increased in $Pb_2(Sc,Nb)O_6$ compositions. The admittance and susceptance values reach a peak at all temperatures, and the magnitude of the peak increases with increasing measuring temperature. Strong frequency dependent of maximum admittance, susceptance, dielectric constant and dielectric loss were observed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.11
• /
• pp.935-940
• /
• 2009

In this research, the composites (100-x)LCP-xBNT (x = 0, 10, 20, 30, 40 vol.%) were fabricated with thermoplastic LCP(Liquid Crystal Polymer) and BNT($BaNd_2Ti_4O_{12}$) which is a high frequency dielectric material. Their dielectric properties, mechanical strength and microstructure were investigated by Impedance analyser, Instron and SEM. In order to fabricate LCP-BNT composites, LCP resin was put into the twin screw type mixer($310^{\circ}C$), melted by keeping for 10 min. After that, BNT filler was dispersed with melted LCP resin for 15 min. in the mixer. For measuring the dielectric properties and mechanical strength, Composite specimens were made by pressing composite granule (LCP-BNT) with 7 ton in the mold at $310^{\circ}C$. With increasing the BNT content (0~40 vol.%) of the composite, Its dielectric constant increased, dielectric loss and flexural strength decreased. The dielectric constant and flexural strength of composites with 20~30 vol.% of BNT filler are 4.1~6.0 and 35~55 MPa respectively. BNT/LCP composite is the potential substrate material for the high frequency application.

• Journal of the Korean Ceramic Society
• /
• v.53 no.2
• /
• pp.178-183
• /
• 2016

Ferroelectric relaxor ceramics with $BaTiO_3-NaNbO_3-Bi(Mg_{1/2}Ti_{1/2})O_3$ ternary compositions (BT-NN-BMT) have been prepared by sol-gel powder synthesis and consequent bulk ceramic processing. Through the modified chemical approach, fine and single-phase complex perovskite compositions were successfully obtained. Temperature and frequency dependent dielectric properties indicated typical relaxor characteristics of the BT-NN-BMT compositions. The ferroelectric-paraelectric phase transition became diffusive when NN and BMT were added to form BT based solid solutions. BMT additions to the BT-NN solid solutions affected the high temperature dielectric properties, which might be attributable to the compositional inhomogeneity of the complex perovskite and resulting weak dielectric coupling of the Bi-containing polar nanoregions (PNRs). The temperature stability of the dielectric properties was good enough to satisfy the X9R specification. The quasi-linear P-E response and the temperature- stable dielectric properties imply the high potential of this ceramic compound for use in high temperature capacitors.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.12
• /
• pp.2166-2172
• /
• 2007

In this study a low-signal equivalent circuit based on the Double Schottky Barrier model is proposed for ZnO-based varistor. Since pin-lead inductance and stray capacitance are considered in pin-lead type ZnO varistor these inductance and capacitance could be removed from the experimental dielectric data of the varistor. According to the equivalent circuit simulation results the higher the varistor-voltage of varistor sample the capacitance of dielectric layer is larger, and the capacitances of semiconducting layer and depletion layer are smaller, while the parallel resistances of semiconducting layer and depletion layer are more larger values. Spectra of the dielectric loss factor $tan{\delta}$ show 2 peaks in low frequency and high frequency regions respectively. The low-frequency peak is due to the relaxation by deep donors and the high-frequency peak is due to the relaxation by shallow donors. Above results are well consistent with the theoretical mechanism of ZnO varistor.