• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.5
• /
• pp.490-496
• /
• 2015

We have grown AlN/GaN heterostructure which is a promising candidate for mm-wave applications. For the growth of the high quality very thin AlN barrier, indium was introduced as a surfactant at the growth temperature varied from 750 to $1070^{\circ}C$, which results in improving electrical properties of two-dimensional electron gas (2DEG). The heterostructure with barrier thickness of 7 nm grown at of $800^{\circ}C$ exhibited best Hall measurement results; such as sheet resistance of $215{\Omega}/{\Box}$electron mobility of $1430cm^2/V{\cdot}s$, and two-dimensional electron gas (2DEG) density of $2.04{\times}10^{13}/cm^2$. The high electron mobility transistor (HEMT) was fabricated on the grown heterostructure. The device with gate length of $0.2{\mu}m$ exhibited excellent DC and RF performances; such as maximum drain current of 937 mA/mm, maximum transconductance of 269 mS/mm, current gain cut-off frequency of 40 GHz, and maximum oscillation frequency of 80 GHz.

• Journal of Korea Society of Industrial Information Systems
• /
• v.1 no.1
• /
• pp.119-233
• /
• 1996

본 논문에서는 게이트의 길이가 0.25$\mu\textrm{m}$dlsGaAs HEMT(High Electron Mobility Transistor)를 이용하여 11.7GHz-12.2GHz 대역 위성통신용 수신기를 설계하였다. 설계된 수신기의 전체이득은 38dB 이상, 잡음지수 1.8dB 이하, 입출력단의 반사손실은 -10dB 이하를 보였다. 수신기는 저잡음증폭기(LNA), 중간주파수증폭기(IFA) , 믹서(Mixer), 국부발진기(LO) 로 구성되어 있으며 LO 주파수와 IF 주파수는 각각 10.75GHz 와 0.95GHz-1.45GHz이고 칩의 크기는 1.7mm $\times$2.5mm이다.

• Journal of IKEEE
• /
• v.17 no.1
• /
• pp.71-76
• /
• 2013

AlGaN/GaN HEMTs (High electron mobility transistors) with narrow channel were fabricated and the effect of channel scaling on the device were investigated. The devices were fabricated using e-beam lithography to have same channel length of $1{\mu}m$ and various channel width from 0.5 to $9{\mu}m$. The sheet resistance of the channel was increased corresponding to the decrease of channel width and the increase was larger at the width of sub-${\mu}m$. The threshold voltage of the HEMT with $1.6{\mu}m$ and $9{\mu}m$ channel width was -2.85 V. The transistor showed a variation of 50 mV at the width of $0.9{\mu}m$ and the variation 350 mV at $0.5{\mu}m$. The transconductance of 250 mS/mm was decreased to 150 mS/mm corresponding to the decrease of channel width. Also, the gate leakage current of the HEMT decreased with channel width. But the degree of was reduced at the width of sub-${\mu}m$. It was thought that the variation of the electrical characteristics of the HEMT corresponding to the channel width came from the reduced Piezoelectric field of the AlGaN/GaN structure by the strain relief.

• Journal of electromagnetic engineering and science
• /
• v.17 no.4
• /
• pp.178-180
• /
• 2017

This study presents a 2-20 GHz monolithic distributed power amplifier (DPA) using a $0.25{\mu}m$ AlGaN/GaN on SiC high electron mobility transistor (HEMT) technology. The gate width of the HEMT was selected after considering the input capacitance of the unit cell that guarantees decade bandwidth. To achieve high output power using small transistors, a 12-stage DPA was designed with a non-uniform drain line impedance to provide optimal output power matching. The maximum operating frequency of the proposed DPA is above 20 GHz, which is higher than those of other DPAs manufactured with the same gate-length process. The measured output power and power-added efficiency of the DPA monolithic microwave integrated circuit (MMIC) are 35.3-38.6 dBm and 11.4%-31%, respectively, for 2-20 GHz.

• Electronics and Telecommunications Trends
• /
• v.36 no.3
• /
• pp.53-64
• /
• 2021

As the 5G service market is expected to grow rapidly, the development of high-power, high-efficiency power amplifiers for the 5G communication infrastructure is indispensable. Gallium nitride (GaN) is attracting great interest as a key device in power devices and integrated circuits due to its wide bandgap, high carrier concentration, high electron mobility, and high-power saturation characteristics. In this study, we investigate the technology trends of Ka-band GaN radio frequency (RF) power devices and integrated circuits for operation in the millimeter-wave band of recent 5G mobile communication services. We review the characteristics of GaN RF high electron mobility transistor (HEMT) devices to implement power amplifiers operating at frequencies around 28 GHz and compare the technology of foreign companies with the device characteristics currently developed by the Electronics and Telecommunication Research Institute (ETRI). In addition, the characteristics of Ka-band GaN monolithic microwave integrated circuit (MMIC) power amplifiers manufactured using various GaN HEMT device technologies are reviewed by comparing characteristics such as frequency band, output power, and output power density of integrated circuits. In addition, by comparing the performance of the power amplifier developed by ETRI, the current status and future direction of domestic GaN power devices and integrated circuit technology will be discussed.

• Journal of Power Electronics
• /
• v.17 no.3
• /
• pp.601-609
• /
• 2017

Gallium nitride (GaN) power switching devices are promising candidates for high switching frequency and high efficiency power conversion due to their fast switching, low on-state resistance, and high-temperature operation capability. In order to facilitate the use of these new devices better, it is required to investigate the device characteristics and performance in detail preferably by comparing with various conventional silicon (Si) devices. This paper presents a comprehensive study of GaN high electron mobility transistor (HEMT) based non-isolated point-of-load (POL) synchronous buck converter operating at 2.7 MHz with a high step-down ratio (24 V to 3.3 V). The characteristics and performance of GaN HEMT and three different Si devices are analytically investigated and the optimal operating point for GaN HEMT is discussed. Zero-voltage switching (ZVS) is implemented to minimize switching loss in high switching frequency operation. The prototype circuit and experimental data support the validity of analytical and simulation results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.4
• /
• pp.394-402
• /
• 2013

This paper presents design, fabrication and ruggedness test of switching-mode power amplifier using GaN(Gallium Nitride) HEMT(High Electron Mobility Transistor) for S-band radar applications. The power amplifier is designed to Class-F for high efficiency. The input signal for the measurement of the power amplifier is pulse signal at $100{\mu}s$ pulse width and duty cycle of 10 %. The measurement results of the fabricated Class-F power amplifier are a power gain of 10.8 dB, an output power of 40.8 dBm, a power added efficiency(PAE) of 54.2 %, and a drain efficiency of 62.6 %, at the center frequency. We proposed reliability test set-up of a power amplifier for ruggedness test. And we measured output power and efficiency according to VSWR(Voltage Standing Wave Ratio) variation. The designed power amplifier achieved output power of 32.6~41.1 dBm and drain efficiency of 23.4~63 % by changing VSWR, respectively.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.11
• /
• pp.902-909
• /
• 1991

A reproducible selective dry etch process of GaAs/AlGaAs Heterostructures for High Electron Mobility Transistor(HEMT) Device fabrication is developed. Using RIE mode with $CCl_{2}F_{2}$ as the basic process gas, the observed etch selectivity of GaAs layer with respect to GaAs/$Al_{0.3}Ga_{0.7}$As is about 610:1. Severe polymer deposition problem, parialy generated from the use of $CCl_{2}F_{2}$ gas only, has been significantly reduced by adding a small amount of He gas or by $O_{2}$ plasma ashing after etch process. In order to obtain an optimized etch process for HEMT device fabrication, we com pared the properties of the wet etched Schottky contact with those of the dry etched one, and set dry etch condition to approach the characteristics of Schottky diode on wet etched surface. By applying the optimized etch process, the fabricated HEMT devices have the maximum transconductance $g_{mext}$ of 224 mS/mm, and have relatively uniform distribution across the 2inch wafer in the value of 200$\pm$20mS/mm.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.4
• /
• pp.342-354
• /
• 2013

The aim of this work is to investigate and study the quantum effects in the modeling of nanoscale symmetric double-gate InAlAs/InGaAs/InP HEMT (High Electron Mobility Transistor). In order to do so, the carrier concentration in InGaAs channel at gate lengths ($L_g$) 100 nm and 50 nm, are modelled by a density gradient model or quantum moments model. The simulated results obtained from the quantum moments model are compared with the available experimental results to show the accuracy and also with a semi-classical model to show the need for quantum modeling. Quantum modeling shows major variation in electron concentration profiles and affects the device characteristics. The two triangular quantum wells predicted by the semi-classical model seem to vanish in the quantum model as bulk inversion takes place. The quantum effects thus become essential to incorporate in nanoscale heterostructure device modeling.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.7
• /
• pp.56-61
• /
• 1997

I $n_{0.53}$G $a_{0.47}$As/I $n_{0.52}$A $l_{0.48}$As pseudomorphic high electron mobility transistor (P-HEMT) structures were grown on semi-insulating InP substrates by molecular beam epitzxy method. The hall effect measuremetn was used to measure the electrical properties and the photoluminescence (PL) measurement was used to measure the electrical properties and the photoluminescence(PL) measurement for optical propety. By the cross-sectional transmission electron microscopy (XTEM) investigation of the V and X shape defects including slip with angle of 60.deg. C and 120.deg. C to surface in the sampel, the defects formation mecahnism in the I $n_{0.52}$A $l_{0.48}$As epilayers on InP substrates could be explained with the different thermal expansion coefficients between I $n_{0.52}$A $l_{0.48}$As epilayers and InP substrate.d InP substrate.