• 대한금속재료학회지
• /
• 제47권2호
• /
• pp.99-106
• /
• 2009

The high temperature corrosion properties of heat resistant steels were investigated in oxidation atmosphere including sulfur dioxide. The heat resistant steels of T22, T92, T122, T347HFG and T304H were evaluated at 620, $670^{\circ}C$ for 400 hours. The corrosion rates showed a decreasing tendency while chrome contents of those steels increased from 2 mass.% to 19 mass.%. The in crease in temperature increasement has an more effect on the corrosion rates of low chrome steels than high chrome steels. The weight gains of T22, T92, T304H at $670^{\circ}C$ were 3.7, 1.65, 1.23 times compared with those at $620^{\circ}C$. The external scale formed on T22 was composed of hematite, magnetite and Fe-Cr spinel and internal layer including iron oxide mixed with sulfide. The scales formed on T92, T122, T304H consisted of an outer layer of hematite and inner layer of chrome oxide and hematite. The proportion of chrome oxide at inner layer was increased when the chrome contents in heat resistant steels were increased.

• Nuclear Engineering and Technology
• /
• 제55권4호
• /
• pp.1468-1475
• /
• 2023

Enhancement of wear resistance of components used in fast reactors is necessary for long service life of the components. Plasma nitriding is a promising surface modification technology to impart high hardness and improved wear resistance of various steel components. This study discusses the characterization of chrome nitrided SS316L casing ring used in secondary sodium pump of fast breeder reactor and its stability under long term sodium exposure. Microstructural and hardness analysis showed that stress relieved component could be chrome nitrided successfully to a thickness of about 100 ㎛. Assessment of in-sodium performance of the chrome nitrided casing ring subjected to long term exposure up to 5000h at 550℃, showed retention of chrome nitrided layer with a case depth almost similar to that before sodium exposure. A slight decrease in the hardness was observed due to prolonged high temperature sodium exposure. Tribological studies indicate very low coefficient of friction indicating the retention of good wear resistance of the coating even after long term sodium exposure.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.802-806
• /
• 2001

Chrome-molybden steel or chrome steel for machine structural use been shown to excellent hardenability adding boron of a small amount at low carbon steel. In the country boron steel has been used widely high strength volt and wear resistant components of construction equipment. SEM results showed classical fatigue fractures, consistent with surface crack initiation. The speciments were cycled using under load controlled rotary bending fatigue tests. In this study, the fatigue crack initiation as well as the fatigue crack growth behavior and the fracture mechanism were investigated through observations of fracture surface boron steel(AISI 51B20).

• 한국정밀공학회지
• /
• 제18권11호
• /
• pp.174-178
• /
• 2001

Chrome-molybden steel or chrome steel for machine structures has been shown to excellent hardenability adding boron of a small amount at low carbon steel. These days, boron steel has been used high strength bolt and wear resistant components of construction equipment. SEM results showed classical fatigue fractures, consist with surface crack initiation. The specimens were tested repeatedly(9 times) under controlled load rotary bending fatigue tests. In the study, the fatigue crack initiation as well as fatigue crack growth behavior and the fracture mechanism were investigated through observations of fracture of boron steel surface(AISI 51B20).

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.956-961
• /
• 2003

Recently, environmental pollution has become a significant problem in industry and many researches have been investigated in order to preserve the environment. Environmentally conscious machining and technology have more and more important position in machining process. In the milling process, the cutting fluid has greatly bad influence on the environment. In this study, the machining of blade parts(12Cr steel) using the cutting fluid, compressed cold air and oil mist etc., also, the productivity and the surface topography was improved by using new end-mil tool considering tool material and shape.

• 한국산업융합학회 논문집
• /
• 제22권2호
• /
• pp.191-199
• /
• 2019

In this paper, dissimilar friction welding were produced using 15 mm diameter solid bar in chrome molybedenum steel(SCM440) to stainless steel(STS316L) to investigate their mechanical properties. Consequently, optimal welding conditions were n=2000 rpm, HP=70 MPa, UP=140 MPa, HT=10 sec and UT=10 sec when the metal loss(Mo) is 8.6 mm. In addition, an acoustic emission technique was applied to evaluate the optimal friction welding condition. AE parameters including the cumulative count, amplitude and energy showed a various changes according to the friction condition. A continuous type waveforms and low frequency spectrum was presented in friction time. On the other hand, a burst type waveform and high frequency spectrum was exhibited in pressing time.

• 한국소음진동공학회논문집
• /
• 제23권4호
• /
• pp.332-337
• /
• 2013

This paper presents a subsequent research work on the roller design of IRB(isolation roller bearing) seismic isolation device presented in Part 1 by focusing on heat treatment. The hardness and friction factor are very important factors of material and after-treatment process selection. Normally, roller bearing consists of roller and retainer. The roller gets high pressure constantly, while the retainer gets tensile and compressive stress. Therefore, sensitive material selection and heat treatment of each part is quite important. In this experimental evaluation, carbon steel, chrome special steel and others are employed and their characteristics after heat treatment are identified. Each material is prepared by refining high frequency heat treatment. The friction factor and static load capacity of manufactured material are experimentally identified and destructive test of material is processed. Optimal material and heat treatment conditions for IRB roller bearing are determined based on experiment results.

• Advances in nano research
• /
• 제13권4호
• /
• pp.313-323
• /
• 2022

The microstructure and mechanical properties of Cr-Ni steel and Cr-Ni steel-matrix nanocomposites reinforced with nano-ZrO₂ particles were investigated in this study. Cr-Ni steel and Cr-Ni/ZrO₂ nanocomposites were produced using a combination of high-energy ball milling, pressing, and sintering processes. The microstructures of the specimens were analyzed using EDX and XRD. Compression and hardness tests were performed to determine the mechanical properties of the specimens. Nano-ZrO₂ particles were effective in preventing chrome carbide precipitate at the grain boundaries. While t-ZrO₂ was detected in Cr-Ni/ZrO₂ nanocomposites, m-ZrO₂ could not be found. Few α'-martensite and deformation bands were formed in the microstructures of Cr-Ni/ZrO₂ nanocomposites. Although nano-ZrO₂ particles had a negligible impact on the strength improvement provided by deformation-induced plasticity mechanisms in Cr-Ni/ZrO₂ nanocomposites, the mechanical properties of Cr-Ni steel were significantly improved by using nano-ZrO₂ particles. The hardness and compressive strength of Cr-Ni/ZrO₂ nanocomposite were higher than those of Cr-Ni steel and enhanced as the weight fraction of nano-ZrO₂ particles increased. Cr-Ni/ZrO₂ nanocomposite with 5wt.% nano-ZrO₂ particles had almost twofold the hardness and compressive strength of Cr-Ni steel. The nano-ZrO₂ particles were considerably more effective on particle-strengthening mechanisms than deformation-induced strengthening mechanisms in Cr-Ni/ZrO₂ nanocomposites.

• 한국안전학회지
• /
• 제23권3호
• /
• pp.12-16
• /
• 2008

For industrial centrifuges, the state of their welding areas, even with a naked-eye observation, offers potential safety problems such as inconsistent bead formation. STS304, which is used mainly in centrifuges, is made of metal alloys with chrome and nickel as the main ingredients, offering excellent corrosion resistance, thermal resistance, and high strength, and thus allowing it to be used for diverse purposes. This paper conducted tensile and fatigue tests of STS304 to improve the safety of centrifuges. In the findings, for the static behavior of the STS304 material, welded specimens increased their yield and tensile strength compared with the base test specimens, but decreased their elongation ratio. Also, the data dispersion phenomenon of welded specimens remarkably increased.

• 한국산학기술학회논문지
• /
• 제18권9호
• /
• pp.61-67
• /
• 2017

프레스금형 제작 시 사용목적에 맞는 적합한 소재선택과 빠른 가공방법에 대한 연구는 금형제작시간을 줄이고 금형원가를 절감하는데 절대적으로 필요한 연구분야이다. 특히 장수명 프레스금형을 개발하기 위해선 열에 대한 고찰이 반드시 이루어져야 한다. 일반적으로 프레스금형의 주요부품 소재로는 Cr, W계 저합금 공구강, 고탄소 고크롬강, 고속도강 등 냉간 금형용 합금공구강이 많이 쓰이고 있다. 프레스금형부품을 가공하는 데는 주로 공작기계와 와이어 컷 방전가공을 사용하고 있다. 가공공정에 따라 금형부품의 가공시간 및 수명이 많은 차이가 난다. 밀링가공과 연삭가공으로 제작된 부품의 경우 제작시간과 비용은 많이 드는데 비해 금형의 수명이 길고 밀링가공과 와이어 컷 방전가공을 사용하면 제작시간과 비용은 절감되는 반면 금형수명은 줄어드는 현상이 나타난다. 따라서 본 연구에선 가공시간과 비용이 절감되는 가공방법으로 열처리를 사용하여 금형의 사용수명을 향상시키는 방법에 대해 고찰하고자 한다. 밀링가공-연삭가공, 밀링가공-와이어 컷 방전가공, 밀링가공-와이어 컷-고온템퍼링, 3가지 가공방법으로 시편을 제작하여 가공표면과 중심부를 SEM, EDS분석 및 표면조도분석으로 문제점을 고찰하였고 밀링가공-와이어 컷 방전가공-고온템퍼링의 가공방법으로 밀링가공-연삭가공과 동일한 금형의 수명을 만드는 방법을 도출하였다.