• 한국유체기계학회 논문집
• /
• 제18권1호
• /
• pp.37-43
• /
• 2015

A Beta-type Stirling engine is developed and tested on the operation stability and cycle performance. The flow rate for cooling water ranges from 300 to 1500 ml/min, while the temperature of heat source changes from 300 to $500^{\circ}C$. The internal pressure, working temperatures, and operation speed are measured and the engine performance is estimated from them. In the experiment, the rise in the temperature of heat source reduces internal pressure but increases operation speed, and overall, enhances the power output. The faster coolant flow rate contributes to the high temperature limit for stable operation, the cycle efficiency due to the alleviated thermal expansion of power piston, and the heat input to the engine, respectively. The experimental Stirling engine showed the maximum power output of 12.1 W and the cycle efficiency of 3.0 % when the cooling flow is 900 ml/min and the heat source temperature is $500^{\circ}C$.

• 한국기계가공학회지
• /
• 제17권5호
• /
• pp.23-29
• /
• 2018

This study is about the distribution of heat transfer in air conditioning ducts used for marine vessels and oil drilling platforms. As the convective heat transfer coefficient increased, heat transfer was conducted dynamically to inside as it exited to the outlet of duct. The experiment was to determine if the amount of heat transfer generated at the duct exit increased as the convective heat transfer coefficient increased. When the convective heat transfer coefficient was low, the temperature of the duct showed a relatively high temperature difference between the outside and inside of the duct due to the temperature influence of the internal fluid. In case of temperature distribution generated the volume of the duct along the change of the convective heat transfer coefficient, the temperature descended as heat transfer was promoted and the convective heat transfer coefficient increased.

• 한국기계가공학회지
• /
• 제18권2호
• /
• pp.7-13
• /
• 2019

This study is about distributions of heat transfer in air conditioning duct used for marine and oil drilling ship. As the convective heat transfer coefficient increased, heat transfer was conducted dynamically to inside as it exited to the outlet of duct. So, it was checked that the amount of heat transfer generated at duct increased as the convective heat transfer coefficient increased. In case the convective heat transfer coefficient was low, the temperature of duct showed the relatively high temperature distribution due to the temperature influence of internal fluid as the heat transfer between the outside and inside of the duct. In case of temperature distribution generated the volume of the duct along the change of the convective heat transfer coefficient, it was found out that the temperature descended as heat transfer was promoted and the convective heat transfer coefficient increased.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.1-4
• /
• 2002

This article presents the unique characteristics of cavitation, those are very high pressure and very high temperature even in a very short time. Such the high-pressure causes the destruction of material, which sometimes brings a severe problem to fluid machinery. However, if we look the cavitation from the different direction, such the high pressure can be used to various applications. The author presents two examples of the utilization of cavitation recently done at the Toyo University. Those are 'dispersion of spilled oil' and 'killing planktons'.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.354-361
• /
• 2005

In high speed cutting process, due to the friction between the tool and workpiece, a temperature rise of contacting part is serious. It need to develop cutting tool for overcoming such a poor condition. So now, some studies, the optimization of tool shapes, the fine grains of tool material, multi-layer coating of tools are processing. If mirror finishing on the tool is processed, there is advantage of relation between chip and tool, because of less friction, and also tool's lift would be increased. As a result mirror like finishing is expected efficient enhancement of tool. Generally, it is too difficult to process by a general way for tools of complex shapes, it is required a new method to process such complex shape tools. The magnetic fluid polishing technique can polish the workpiece of complex shape, because the polishing method which polishes as compress the workpiece by the magnetism abrasives to arrange to the linear according to the line of magnetic force. In this paper, We polished the surface of the high speed cutting tool using the magnetic fluid polishing technique, to enhance the performance of the high speed cutting tool.

• 한국가스학회지
• /
• 제16권2호
• /
• pp.9-13
• /
• 2012

본 연구에서는 화력발전소의 재열기 내에 과열증기가 이상 고온이 될 때 과열증기를 냉각하는 과열증기 냉각기의 온도 안전성에 대하여 열전달 해석을 통해 진단하였다. 과열증기 냉각기 내부에 냉각을 위해 액체상태의 냉각수가 밀폐 공간 내에 존재한다. 이곳은 고온의 과열증기에 노출되어 있는 부분으로 가열에 의해 비등이 발생하면 내부 압력이 상승하여 냉각기가 견딜 수 있는 허용 압력 이상으로 되게 된다. 이렇게 되면 냉각기가 파손되거나 냉각수가 역류가 일어나서 안전하지 않게 된다. 본 연구에서는 이의 진단을 위해 냉각기의 형상을 합리적으로 단순화 하고 단열재 여부, 내부 냉각수의 자연대류 유동 고려 여부 등으로 구분하여 4 가지 경우의 열전달 해석을 수행 하였다. 냉각기 내부에 있는 액체 상태의 냉각수에 대하여 자연대류 유동을 고려하지 않는 경우는 온도 상승과 이에 따른 압력 상승으로 안전하지 않은 것으로 나타났다. 그러나 실제 현상인 냉각수의 자연대류 유동을 고려하고 단열재를 사용한 경우에는 냉각수의 자연대류 유동에 따른 고온 영역에서 저온 영역으로 활발한 열전달이 발생하여 냉각수가 허용온도와 허용압력 이하에서 운전되고 있음을 알았고 이에 따라 과열증기 냉각기는 안전하다는 것을 판단할 수 있었다.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 춘계학술발표대회 논문집
• /
• pp.227-232
• /
• 2008

Stirling engine for solar thermal power is an essential part of Dish-Stirling system which generates electricity by using direct normal irradiation and will go into commercialization in near future. For the Stirling engine used in this study is Solo 161 model the capacity of which is 10 kWe and was already used for the Dish-Stirling system of KIER in Jinhae. The receiver of Stirling engine absorbes concentrated solar radiation and transfer it to working fluid of Hydrogen. The working condition of striling engine is high temperature and high pressure to make high efficiency. Therefore the receiver should stand against high temperature of above 800 $^{\circ}C$ and high pressure of max. 150 bar with good performance of heat transfer. The receiver is composed of 78 Inconel tubes of 1/8" with thickness of 0.71 mm and two reserviors which is connected with two cylinders. In order to know the charaterristics of heat transfer of Stirling engine receiver, simulation on the heat transfer of the receiver of Solo 161 is conducted by using CFD code of Fluent. The heat flux on the receiver surface has a shape of Gaussian distribution so, it is necessary to simulate a whole receiver. However, It is difficult and time consuming to simulate the whole receiver that one tube with different heat flux conditions are considered in this study. From the simulation results, heat transfer charateristics of receiver are observed and tube wall and fluid temperature and heat transfer coefficient are obtained and compared with the calculated results from Dittus-Boelter's correlation.

• Nuclear Engineering and Technology
• /
• 제52권2호
• /
• pp.271-278
• /
• 2020

The investigation into a full-scale 27 m high, by 6 m wide, thermosyphon loop. The simulation model is based on a one-dimensional axially-symmetrical control volume approach, where the loop is divided into a series of discreet control volumes. The three conservation equations, namely, mass, momentum and energy, were applied to these control volumes and solved with an explicit numerical method. The flow is assumed to be quasi-static, implying that the mass-flow rate changes over time. However, at any instant in time the mass-flow rate is constant around the loop. The boussinesq approximation was invoked, and a reasonable correlation between the experimental and theoretical results was obtained. Experimental results are presented and the flow regimes of the working fluid inside the loop identified. The results indicate that a series of such thermosyphon loops can be used as a cavity cooling system and that the one-dimensional theoretical model can predict the internal temperature and mass-flow rate of the thermosyphon loop.

• Safety and Health at Work
• /
• 제8권1호
• /
• pp.42-48
• /
• 2017

Background: As one of the most frequently occurring accidents in a chemical plant, a fire accident may occur at any place where transfer or handling of combustible materials is routinely performed. Methods: In particular, a jet fire incident in a chemical plant operated under high pressure may bring severe damage. To review this event numerically, Computational Fluid Dynamics methodology was used to simulate a jet fire at a pipe of a compressor under high pressure. Results: For jet fire simulation, the Kemeleon FireEx Code was used, and results of this simulation showed that a structure and installations located within the shelter of a compressor received serious damage. Conclusion: The results confirmed that a jet fire may create a domino effect that could cause an accident aside from the secondary chemical accident.

• 대한환경공학회지
• /
• 제31권11호
• /
• pp.1033-1040
• /
• 2009

고효율 싸이클론의 설계는 압력강하의 최소화와 집진효율의 최대화를 이루는 것이 중요하다. 본 연구는 고온, 고압 조건하에서 신뢰성 있는 컴퓨터 프로그램을 개발하여 싸이클론의 집진효율에 영향을 주는 물리적 메카니즘을 연구하는 것이다. 수치 해석적 연구를 통한 고온, 고압 조건에서의 압력강하 계산은 실험데이터와 비교적 잘 일치하였다. 온도와 압력은 일반적으로 집진효율에 중요한 영향을 미치는데 보통 항력에서 가스의 밀도나 점도 등에 영향을 주어서로 상반되는 결과를 나타낸다. 그러므로 고온 운전에 따른 집진효율의 감소는 고압 조건으로 운전하는 것이 대안이 될 것으로 판단된다. 집진효율에 영향을 주는 인자에 대해 좀 더 세부적인 연구를 위하여 접선방향 속도나 보텍스 파인더의 직경 등과 같은 싸이클론의 설계변수나 운전변수에 따른 연구를 수행하였다. 예상한 바와 같이 접선방향의 속도가 집진효율에 가장 큰 영향을 주었다. 그리고 보텍스 파인더의 직경이 증가할수록 집진효율은 감소하였으며 보텍스 파인더의 길이는 집진효율에 큰 영향을 나타내지 않았다.