• Journal of The Korean Society of Grassland and Forage Science
• /
• v.18 no.2
• /
• pp.79-88
• /
• 1998

This experiment was conducted from May to August in 1997 to selected the wrn hybrids being suitable for silage at farm in the Kongju National University through the comparison of growth characteristics, forage yield and growth analysis about native and imported corn hybrids for silage production. In this experiment, trial design was a randomized block design with three replication, testing varieties were 4 hybrids (Suwon 19, Kwanganok, Whengsungok, Suwonok ) of native corn hybrids and 13 hybrids (P 3156, P 3352, P 3144w, DK 501, DK 689, DK 713, DK 729, H 643.99, H 545.64, H 645.12, HC 7466, H 644.18, H ALISEO) of imported corn hybrids. The results obtained are summarized as follows; 1. The emergence rate of H643.99 was the highest with 97.0%. In rice black streaked dwarf virus(RBSOV), the hybrid of HC 7466 was lower infected with 1.6% than other hybrids. The plant hight of P 3144w was the highest with 339 cm and the stem length of P 3156 was the highest with 261 cm. In native com hybrids, the plant height and stem length of Kwanganok were recorded with 306 cm and 235 cm, respectively. 2. Leaf number and leaf area of Kwanganok were the greatest with 16 sheet per plant and $5,180\;{\textrm{m}^2}/l0a$, respectively. H 645.12 and H 545.64 had the greatest in ear to total dry matter ratio with 49.5% and 49.4%, respectively. 3. The fresh matter yield was significantly difference between growth stage, So Suwon 19 had the most level at 15 days before silking, P 3352 had the most level at silking date, Kwananok had the most level at 35 days a after silking. The fresh matter yield of native com hybrids such as Suwon 19 and Kwanganok was not apparent diffreences as compared with imported corn hybrids. 4. As the results of survey with dry weight, the quantity of dry matter accumulation were increase after silking. The varieties of P 3352, P 3156, Kwanganok, OK 713 were more quantity of dry matter production than DK 501, HC 7466. The Kwanganok of native com hybrid and Pioneer strain with high percentage of dry matter were higher dry weight than Limagrain strain. 5. HC 7466 had the largest LAR with $6.53\;{\textrm{cm}^2}/g$, H545.12 had the lowest LAR with $3.30\;{\textrm{cm}^2/g}$. P 3144 had the largest LAI, DeKalb strain including DK 713 were larger apparently than Limagrain strain including HC 7466 with 3.15. 6. The RGR of testing varieties was little difference of statistical significantly, but DK 501, and HC 7466 were lower than other corn hybrids. The CGR of native and American varieties was no apparent differences, but that of Limagrain strains were a large variation. According to the results obtained by this experiment, the eary growth such as emergence rate and RBSDV infection rate of Limagrain strains was more excellent than other strains. P 3156, P 3352, P 3144w, DK 713 and HC 7466 were suitable for silage condition such as dry matter yield, percentage of dry matter and % ear to total dry matter. The fresh and dry matter yield of native corn hybrids such as Suwon 19 and Kwanganok were not apparent differences as compared with imported corn hybrids, but percentage of dry matter was lower than other imported corn hybrids.

• The Korean Journal of Zoology
• /
• v.13 no.3
• /
• pp.68-74
• /
• 1970

In the previous studies, the present author found that high proportion of the follicular oocytes from mouse and rabbit ovaries are able to resume their maturation division in the anterior chamber of the eye in which they have been incubated by auto- or homoplastic transplantation. Especially in the case of the homoplastic transplantation, it was known that no trouble has been detected in the process of resumption of the oval maturation in particular connection with the antigen-antibody reaction between donor and recipient. These findings provide a possibility that the follicular oocytes from various animals would be matured in the eye even after the xenoplastic transplantation. Under such an assumption, the present studies were performed to examine the behavior of the follicular oocytes in the eye chamber of the animals of different species. For the donor of the follicular oocytes, domestic rabbits, albino rats of Sprague-Dowley strain, and albino mice of A-strain bred in our laboratory were used. The oocytes obtained from the ovarian follicules were introduced to the anterior chamber of the eye of different species of animals, with an exception of rabbit in which only the female animals were used as a recipient. The procedures of collection of ova, introduction to the eye, harvest from the eye ball, fixation, and staining were the same as mentioned in the previous reports (Cho, 1967b; Cho and Kim, 1968). The conclusions obtained are summarized as below. 1. The rabbit follicular oocytes are able to mature in the eye chambers of both male mouse and rat, although the proportion of the maturation is lower than when they are incubated autoplastically in the eye. When the ova were incubated in the male mouse eye for 24 hours, 21 per cent of them showed chromosomes at metaphase I and II, whereas the rate was 32 per cent when they were incubated in the eye of the male rat. These are apparently low comparing to the rate of 52 per cent of autoplastic transplantation. 2. When rat follicular oocytes were transferred into the mouse eye chamber and recovered after 24 hours, 43 per cent of them produced the mataphase I and II chromosomes. This proportion was higher than the result of the homoplastic transplantation which yielded 23 per cent of the ova on maturation. 3. The most striking result was found in the experiment with mouse follicular oocytes. Seventy-six per cent of the oocytes resumed their maturation division within 24 hours after they were transferred into the male rat eye chamber, and this figure was significantly high compared to the result o 55 per cent obtained by the homoplastic transplantation. In the rat eye, the induction of the degenerative ova also was low (19%). On the other hand, the proportion of the oval maturation decreased to 45 per cent, while that of degeneration increased 33 per cent when they were incubated in the eye of the female rabbit. 4. It was apparent from the present experiments that the follicular oocytes can reveal their activation to maturation in the eye chamber which contains aqueous humor which is known to be composed of low protein content and of very little gamma-globulin which acts as an antibody(Oser, 1965), and that it shows higher osmolarity than blood serum(Levene, 1958). Taking these properities into consideration the humor may provide unfavourable environment to the cells and tissues incubated in. However, it could be noteworthy finding that only the follicular oocytes in the eye of the different species can grow in healthy condition although the maturation rates are varied with the animal species. The fact that the rabbit follicular oocytes show the lower proportion in maturation may be due to the greater amount of the yolk granules in the egg cytoplasm than those in the mouse and rat oocytes. That the mouse oocytes incubated in the eye of the rat mouse and rat oocytes. That the mouse oocytes incubated in the eye of the rat resumed their maturation process in greater proportion would e explained by the fact that the rat eye chamber particularly provides the better environment to the mouse oocytes than the eye chamber of mouse does.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Applied Biological Chemistry
• /
• v.37 no.4
• /
• pp.295-302
• /
• 1994

For the development of biological wastewater treatment process using photosynthetic bacteria (PSB), photosynthetic sludge process consisted of anaerobic digestion and PSB reactor were designed for the treatment of swine wastewater and the optimal operating conditions in flask-scale were examined. Photosynthetic bacteria from soil, pond, rice field, ditch etc. were isolated in synthetic medium containing high amount of organic acids and finally isolated one strain KK14 which showed the most degradating ability of organic acids was selected for the treatment of swine wastewater. It was identified as Rhodopseudomonas palustris. In the anaerobic digestion stage, the maximum organic acid productivity was obtained at pH 5.0, $37^{\circ}C$, HRT 2 day and under anaerobic standing condition. The optimal operating conditions of PSB reactor for the treatment of swine wastewater were pH 7.0, $30^{\circ}C$ under 4,000 lux illumination, and optimal initial COD loading (kg COD/kg D. C. W of PSB) was 2 (20% v/v seeding) in the main purification stage. Maximum removal rate of COD reached 92% under the above optimal conditions for 5 days.

• Food Science of Animal Resources
• /
• v.28 no.5
• /
• pp.587-595
• /
• 2008

In order to develop a new starter for fermented milk, 1037 bacterial strains were isolated from raw milk. The strain that showed excellent acid producing and angiotensin converting enzyme (ACE) inhibitory activity (88.6%) was selected and identified as a Lactobacillus zeae based on the result of API carbohydrate fermentation pattern and 16S rDNA sequence. Lactobacillus zeae RMK354 was investigated further to study its physiological characteristics. It showed strong ACE inhibitory activity compared with commercial LAB starters tested. The optimum growth temperature of L. zeae RMK354 was $40^{\circ}C$ and it took 10 hr to reach pH 4.3 under this condition. L. zeae RMK354 showed more sensitive to penicillin-G, bacitracin, novobiocin, in a comparison of 14 different antibiotics, and showed most resistance to polymyxin B and vancomycin. It showed higher esterase and leucine arylamidase activities compared with 16 other enzymes. It was comparatively tolerant to bile juice and able to survive at pH 2 for 3 hr. It showed inhibitory activity against Salmonella Typhimurium with the rate of 60%. Based on these and previous results, L. zeae RMK354 could be an excellent starter culture for fermented milk with high level of ACE inhibitory activity.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.1
• /
• pp.1-10
• /
• 2018

Recently, there has been rapid development in the field of flexible electronic devices, such as organic light emitting diodes (OLEDs), organic solar cells and flexible sensors. Encapsulation process is added to protect the flexible electronic devices from exposure to oxygen and moisture in the air. Using numerical simulation, we investigated the effects of the encapsulation layer on mechanical stability of the silicon chip, especially the fracture performance of center crack in multi-layer package for various loading condition. The multi-layer package is categorized in two type - a wide chip model in which the chip has a large width and encapsulation layer covers only the chip, and a narrow chip model in which the chip covers both the substrate and the chip with smaller width than the substrate. In the wide chip model where the external load acts directly on the chip, the encapsulation layer with high stiffness enhanced the crack resistance of the film chip as the thickness of the encapsulation layer increased regardless of loading conditions. In contrast, the encapsulation layer with high stiffness reduced the crack resistance of the film chip in the narrow chip model for the case of external tensile strain loading. This is because the external load is transferred to the chip through the encapsulation layer and the small load acts on the chip for the weak encapsulation layer in the narrow chip model. When the bending moment acts on the narrow model, thin encapsulation layer and thick encapsulation layer show the opposite results since the neutral axis is moving toward the chip with a crack and load acting on chip decreases consequently as the thickness of encapsulation layer increases. The present study is expected to provide practical design guidance to enhance the durability and fracture performance of the silicon chip in the multilayer package with encapsulation layer.

• The Korean Journal of Mycology
• /
• v.6 no.1
• /
• pp.29-41
• /
• 1978

This study aims to brew apple wine containing lower concentration of alcohol by fermentation and to retain $CO_2$ gas in apple wine, and investigation for the possibility of storage at room temperature was performed. A Saccharomyces sp. was proved to be acceptable for production of base wine as its higher fermentation rate at $20{\sim}25^{\circ}C$. However, B-2 was most reasonable for post-fermentation of apple wine as this strain strongly ferments sugars at low temperature $(4^{\circ}C)$. The yield of apple juice increased by maceration of apple pulps. The yield was about 5 % more than that of the unmacerated juice, whereas acid content was decreased by 10% compared with control. When stored apple wine containing 9% alcobol was introduced $1{\sim}3%$ sucrose at $7{\sim}8^{\circ}C$ for 100 days or more, the $CO_2$ pressure of apple wine in bottle shows $3kg/cm^2$ by bottle-pressure meter. It showed good storage of the wine at room temperature. $CO_2$ gas pressure in apple wine containing 6% alcohol, $5{\sim}10%$ hop extract, and 2% sugar was $2kg/cm^2$, he result also showed possibility of storage. Whereas 6% concentration of alcoholic apple wine without hop extract caused unusual fermentation during storage at the same condition. The desirable conditions for high quality apple wine should have $CO_2$ pressure of $2kg/cm^2$ or more and should be added $1{\sim}2% sugar to base wine. From these results, it can be concluded that the brewing of lower alcoholic apple wine is possible.

• Korean Journal of Poultry Science
• /
• v.32 no.4
• /
• pp.291-300
• /
• 2005

Two experiments were carried out to assess the appropriate incubation conditions namely; duration, moisture content and the ideal microbial inoculant for fermented dried food waste(EW) offered to broilers. The nutrient utilization of birds fed the FW diets at varying dietary inclusion rates was also compared with a control diet. In Experiment 1, different moisture contents(MC) of 30, 40, 50 and $60\%$ respectively were predetermined to establish the ideal duration of incubation and the microbial inoculant. A 1mL Aspergillus oryzae(AO) $(1.33\times10^5\;CFU/mL)$ was used as the seed inoculant in FW. This results indicated that the ideal MC for incubation was $40\~50\%$ while the normal incubation time was > 72 hours. Consequently, AO seeds at 0.25, 0.50, 0.75 and 1.00mL were inoculated in FW to determine its effect on AO count. The comparative AO count of FW incubated for 12 and 96 hours, respectively showed no significant differences among varying inoculant dosage rates. The FW inoculated with lower AO seeds at 0.10, 0.05 and 0.01mL were likewise incubated for 72 and 96 hours, respectively and no changes in AO count was detected(p<0.05). The above findings indicated that the incubation requirements for FW should be $%40\~50\%$ for 72 hours with an AO seed incoulant dosage rate of 0.10mL. Consequently, in Experiment II, after determining the appropriate processing condition for the FW, 20 five-week old male Hubbard strain were used in a digestibility experiment. The birds were divided into 4 groups with 5 pens(1 bird per pen). The dietary treatments were; Treatment 1 : Control(Basal diet), Treatment 2 : $60\%$ Basal+4$40\%$ FW, Treatment 3 : $60\%$ $Basal+20\%\;FW+20\%$ AFW(Aspergillus oryzae inoculate dried food-waste diet) and Treatment 4: $60\%$ Basal+$40\%$ Am. Digestibility of treatment 2 was lowed on common nutrients and amino acids compared with control(p<0.05) and on crude fat and phosphorus compared with AFW treatments(T3, T4)(plt;0.05). Digestibility of treatment 3 and 4 increased on crude fiber and crude ash compared treatment 2 (p<0.05). Digestibility of control was high on agrinine, leucine, and phenylalnine of essential amino acids compared with treatment 3 and 4(p<0.05), and diestibility of treatment 3 and 4 was improved on arginine, lysine, and threonine of essential amino acids. Finally, despite comparable nutrient utilization among treatments, birds fed the dietary treatment containing AO tended to superior nutrient digestion to those fed the $60\%$ Basa1+$40\%$ FW.