• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.267-270
• /
• 2002

Downlink Shared Channel (OSCH) is used for high-speed packet service transmission in WCOMA. The power-controlled performances of the OSCH are studied through simulation works. Under various channel conditions and mobile speeds, the simulation results show that current power control scheme in WCDMA, especially for the OSCH power control, has some problems. In this paper, cause of problems is revealed. Also, the quantitative result related to the OSCH power control problem is analyzed.

• Journal of Power Electronics
• /
• v.9 no.4
• /
• pp.582-592
• /
• 2009

This paper proposes a new speed sensorless direct torque and flux controlled interior permanent magnet synchronous motor (IPMSM) drive. Closed-loop control of both the torque and stator flux linkage are achieved by using two proportional-integral (PI) controllers. The reference voltage vectors are generated by a SVM unit. The drive uses an adaptive sliding mode observer for joint stator flux and rotor speed estimation. Global asymptotic stability of the observer is achieved via Lyapunov analysis. At low speeds, the observer is combined with the high frequency signal injection technique for stable operation down to standstill. Hence, the sensorless drive is capable of exhibiting high dynamic and steady-state performances over a wide speed range. The operating range of the direct torque and flux controlled (DTFC) drive is extended into the high speed region by incorporating field weakening. Experimental results confirm the effectiveness of the proposed method.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.190-196
• /
• 1993

Internal high speed grinding under several high grinding wheel speed condition has been performed in this study for the effects have analyzed and compared with the grinding power, grinding tangential force and accuracy of surface with the carbon tool steel(SK3). The following results have been obtained: (1) Under the workpiece speed constant condition, increasing the grinding speed, the tangential force is decreased, and on the contrary, accuracy of surface is improved. (2) Under the speed ratio (V$_{w}$/V$_{s}$) contant condition it is possible to increase the high machining efficiency constraint to tangential grinding force constant.ant.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.6
• /
• pp.58-70
• /
• 1997

In this paper, an 8bit CMOS low power, high-speed current-mode folding and interpolation A/D converter is designed with te LG semicon $0.8\mu\textrm{m}$ N-well single-poly/double-metal CMOS process to be integrated into a portable image signal processing system such as a digital camcoder. For good linearity and low power consumption, folding amplifiers and for high speed performance of the A/D converter, analog circuitries including folding block, current-mode interpolation circuit and current comparator are designed as a differential-mode. The fabricated 8 bit A/D converter occupies the active chip area of TEX>$2.2mm \times 1.6mm$ and shows DNL of $\pm0.2LSB$, INL of <$\pm0.5LSB$, conversion rate of 40M samples/s, and the measured maximum power dissipation of 33.6mW at single +5V supply voltage.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.3
• /
• pp.274-281
• /
• 2012

This paper discusses the issues associated with the design of high speed machines for applications with a wide constant-power region requirement. Using described multi-domain design environments which put equal weight on the electromagnetic, thermal and mechanical considerations, the suitability and power density achievable using Induction Machines (IM) and Permanent Magnet Synchronous Machines (PMSM) are compared.

• Journal of Power System Engineering
• /
• v.14 no.5
• /
• pp.30-35
• /
• 2010

Recently, the large capacity draft fans in power plants had been changed to variable speed type to educe the power consumption. But the fan experienced the unexpected vibration at specific speed regions. In this study, the high vibration frequency of the fan was confirmed and the natural frequency of the rotor were measured and analyzed by FEM programs. It was analyzed that the vibration was caused by the resonance at the frequency, 30.7Hz. So, the rotor vibration characteristic was changed by adjusting the distance between the shaft bearings. It was conformed the high vibration was disappeared over the all operation speeds.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.64-68
• /
• 1997

In this paper, a controller for the linear motor with high speed and stiffness is implemented using SERCOS interface which is a real time communication protocol between the numerical controller(NC) and the motor driver. The proposed controller is mainly composed of current, speed, and position controller, which are designed using the 32-bit DSP(TMS320C31), a high-integrated logic device (EPM7128), and Intelligent Power Module(IPM) to enhance reliability and compactness of the system. The experimental results show the effective performance of the proposed controller for he linear motor with high speed and stiffness.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.2 no.2
• /
• pp.8-13
• /
• 2005

This paper investigates a fast, accurate and inexpensive hydraulic motor speed control system using high speed on-off solenoid valves. In order to retain the advantages of the two position valve and obtain better performance, the valves are operated by pulse width modulation(PWM) control. PWM signal is generated from a LabWIEW program in microcomputer in order to set up various duty ratio and frequency of carrier wave in PWM signal with varying system parameters. As the results of experiments, the speed control of a hydraulic motor was successfully implemented using on-off solenoid valves. In order to attenuate the pressure ripple and speed variation due to discontinuously controlled flow through the on-off valves, a resonator hose fabricated for automobile power steering system was connected between the valve and a hydraulic motor. From experimental results obtained in the hydraulic motor system with a resonator hose, it was ascertained that the resonator hose showed excellent performances in reducing pressure ripple and motor speed variation.

• Atmosphere
• /
• v.21 no.4
• /
• pp.439-446
• /
• 2011

NCEP reanalysis data were analyzed in order to provide distribution of global wind resource and wind speed in the surface layer for the years 2000-2009. Wind speed at 10 m above ground level (AGL) was converted to wind speed at 80 m above the ground level using the power law. The global average 80 m wind speed shows a maximum value of $13ms^{-1}$ at the storm track region. High wind speed over the land exists in Tibet, Mongolia, Central North America, South Africa, Australia, and Argentina. Wind speed over the ocean increased with a large value in the South China Sea, Southeast Asia, East Sea of the Korea. Sea surface wind in Western Europe and Scandinavia are suitable for wind farm with a value of $7-8ms^{-1}$. Areas with great potential for wind farm are also found in Eastern and Western coastal region of North America. Sea surface wind in Southern Hemisphere shows larger values in the high latitude of South America, South Africa and Australia. The distribution of low-resolution reanalysis data represents general potential areas for wind power and can be used to provide information for high-resolution wind resource mapping.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.583-584
• /
• 2008

This paper presents a low-power and high-speed pulsed flip-flop based on dual-precharging and conditional discharging. The dual-precharging operation minimizes the parasitic capacitance of each precharge node, resulting in high-speed operation. The conditional-discharging operation minimizes the redundant transitions of precharge nodes, resulting in low-power operation. Linear feedback shift register (LFSR) designed in a $0.18{\mu}m$ CMOS technology using the proposed flip-flop achieves 32% power reduction as compared to conventional design.