• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.19-22
• /
• 1997

The objective of this research is to use an analytical and experimental approach to develop optimal tool geometry for high speed machining. The tool geometry parameters and cutting process have complex relationships. Until now, numerous cutting tests were needed to acquire optimal design of endmill for the purpose of high speed machining, dut to the insufficient knowledge about process in high speed machining. In order to improve the cutting ability of endmill, a model for optimal cutter shape was developed to minimize resultant cutting force by combing cutting force and wear test and surface roughness test from optimized and conventional cutter with the same cutting condition. Using various tools with different geometry, relationships between the tool geometry parameter, rake angle, clearance angle, lengh of cutter have been stuied.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.6
• /
• pp.111-118
• /
• 2014

Aluminum lithium alloys are new materials developed for lightweight aircraft parts. However, as compared with conventional aluminum alloys in high-speed machining, problems such as tool wear, machining distortion, and cutting ability arise. This study presents the machining distortion characteristics of an Al-Li alloy wing tip in relation to the cutting heat in high-speed machining. A machining experiment was conducted with high-speed machining equipment for an evaluation of the machining distortion characteristics, with each machining stage temperature change of the workpiece machining surface, and the inside and outside temperature changes of the equipment measured. By measuring the amount of distortion of the workpiece before and after machining, the cutting heat was analyzed with regard to its effect on machining distortion in the product.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.239-242
• /
• 1999

In this paper, we report the process/device design of high-speed, high-voltage SOI smart power IC for mobile communication system, high-speed HDD system and the electronic control system of automobiles. The high voltage LDMOS with 70V breakdown voltage under 0.8${\mu}{\textrm}{m}$ design rule, the high voltage bipolar with 40V breakdown voltage for analog signal processing, the high speed bipolar with cut-off frequency over 20㎓ and LDD NMOS for high density were proposed and simulated on a single chip by the simulator DIOS and DESSIS. And we extracted the process/device parameters of the simulated devices.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.436-440
• /
• 1997

Recently the needs the interest for the high speed motor drive system is increased in many different fields. So in this paper, the high speed motor drive system is proposed to drive the high speed motor using DSP which was developed in order to process datas at high speed. The motor drive is performed using a variable V/f PWM control.

• Journal of the Korean Society for Heat Treatment
• /
• v.35 no.5
• /
• pp.262-269
• /
• 2022

In order to process materials such as engineering plastics, which are difficult to mold due to their high strength compared to conventional polymer materials, it is necessary to improve the hardness and strength of parts such as screws and barrels of injection equipment in extrusion system. High-velocity oxygen fuel (HVOF) process is well known for its contribution on enhancement of surface properties. Thus in this study, using the HVOF process, WC coating layers of different thicknesses were bonded to the surface of S30C substrate by controlling the movement speed of the spray nozzle and each property was evaluated to decide the optimization condition. Through the results, the thickness of WC coating layer increased from 0 to 200 ㎛ maximum, along with the decrement of nozzle movement speed and the surface hardness get increased. Especially, the coated layer with the thickness over 180 ㎛ under the nozzle speed 500 mm/s had high hardness than thinner layer. In addition, the amount of wear consumed per unit time was also significantly reduced due to the formation of the coating layer.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.12
• /
• pp.2028-2038
• /
• 2003

High-speed feed drive systems have been widely used in the manufacturing and semiconductor industries. Specifications for high-speed systems require more advanced capabilities than conventional feed drive systems. It is necessary to devise special design concepts to achieve the level of performance for high-speed feed drive systems. In this paper, an integrated design method is proposed for high-speed feed drive systems in which the interactions between mechanical and electrical subsystems ought to be considered simultaneously during the design process. Based on the integrated design method, a nonlinear optimal design procedure of mechanical subsystems considering the Abbe and radius errors is accomplished through the design process of electrical subsystems satisfying the control stability and the saturation condition of actuators as well as the relative stability. Both mechanical and electrical parameters are considered as design variables. Simulations and numerical case studies show that the integrated design method of high-speed feed drive systems creates results satisfying the desired performances of mechatronic systems.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.5
• /
• pp.13-19
• /
• 2011

In this paper, the active monitoring and control system is developed. This system can monitor the status of high the speed spindle in real time during its processing, and can analyze its influence of dimensional accuracy and processing if any, and can control the machining condition to realize the machining system equipped with active monitoring and self-diagnostic features. Machining experiment was performed on 3 materials Al, Brass and S45C in order to derive the relation between active monitoring and control algorithm by the machining load. In addition, we measured surface roughness of processing specimen along with the data change of spindle rotating speed and conveying speed according to variation of machining load. Based on these experiments, we derived relations for each material that can be applied to the control algorithm to allow self control of the rotating speed and conveying speed according to the machining load.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.427-430
• /
• 2005

Improving the productivity of steel cord is required due to the increase in demand for it, even though steel cord being used as a reinforcement of a tire has been produced at multi-pass wet wire drawing process over 1000m/min. To improve the productivity, if just increase drawing speed, it causes temperature rise, fracture arisen by embrittlement during drawing process. To increase drawing speed affecting productivity, the variation of wire temperature during multi-pass wet wire drawing process is investigated in this study. In result, the multi-pass wet wire drawing process is redesigned. The redesigned wet drawing process with 27 passes efficiently controls wire temperature during drawing process. It, therefore, enables drawing process to be possible at ultra high speed with 2000m/min. It becomes possible to improve the productivity of steel cord in this paper because the increase in drawing speed could be achieved.

• International Journal of Precision Engineering and Manufacturing
• /
• v.8 no.1
• /
• pp.27-31
• /
• 2007

A rolling speed dependent spread model is proposed for predicting the exit cross sectional shape in oval-round (or round-oval) pass rod rolling process when the rolling speed is very high. The effect of rolling speed on the exit cross sectional shape is measured by performing a four-pass continuous high speed (${\sim}80m/s$) rod rolling test and is described in terms of the spread correction parameter. The validity of the model is examined by applying it to rod rolling process at POSCO No.3 Rod Mill. The cross sectional shapes of workpiece predicted by the proposed model coupled with the surface profile prediction $method^{6}$ are in good agreement with those obtained experimentally.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.2
• /
• pp.152-158
• /
• 2012

A newly developed attachment type high-speed spindle can be easily attached to the conventional CNC machining center to allow high-speed machining with low investment costs. This study has focused on the application of a conventional CNC machining center equipped with an attachment type high-speed spindle. A specimen of plastic mold material has been machined to compare the cutting effectiveness of the high-speed machining center and the conventional machining center with the attachment type high-speed spindle respectively. The rotational accuracy of the spindles are measured by a transmission optic measurement system and the surface roughness of the workpiece in accordance with revolution speed(rpm) of the spindle are investigated respectively. As the experimental results, it was shown that the surface roughness of the machined workpiece was $3.42{\mu}mR_{max}$, $0.46{\mu}mR_a$ in the case of attachment type spindle and $1.81{\mu}mR_{max}$, $0.275{\mu}mR_a$ in the case of the high-speed machining center. Moreover, the mean rotational accuracy was $7.57{\mu}m$ in the case of the attachment type spindle and $7.39{\mu}m$ in the case of the high-speed machining center.