• 대한기계학회논문집B
• /
• 제30권5호
• /
• pp.446-456
• /
• 2006

The effect of relative position of the stationary turbine blade for the fixed vane has been investigated on blade tip and shroud heat transfer. The local mass transfer coefficients were measured on the tip and shroud fur the blade fixed at six different positions within a pitch. A low speed stationary annular cascade with a single turbine stage was used. The chord length of the tested blade is 150 mm and the mean tip clearance of the blade having flat tip is 2.5% of the blade chord. A naphthalene sublimation technique was used for the detailed mass transfer measurements on the tip and the shroud. The inlet flow Reynolds number based on chord length and incoming flow velocity is fixed to $1.5{\times}10^5$. The results show that the incoming flow condition and heat transfer characteristics significantly change when the relative position of the blade changes. On the tip, the size of high heat/mass transfer region along the pressure side varies in the axial direction and the difference of heat transfer coefficient is up to 40% in the upstream region of the tip because the position of flow reattachment changes. On shroud, the effect of tip leakage vortex on the shroud as well as tip gap entering flow changes as the blade position changes. Thus, significantly different heat transfer patterns are observed with various blade positions and the periodic variation of heat transfer is expected with the blade rotation.

• 한국추진공학회지
• /
• 제2권1호
• /
• pp.1-12
• /
• 1998

본 연구에서는 기존에 수행되었던 초음속 이젝터에 대한 실험적 연구 및 수치계산 결과에 대한 타당성을 검증하고, 이젝터 유동을 보다 명확히 해석하기 위하여 이젝터 목을 가지는 초음속 이젝터 유동 장에 대하여 k-$\varepsilon$ 난류모델을 적용하였다. 수치계산은 3~200까지의 매우 넓은 범위의 이젝터 작동 압력비에 대하여 수행되었으며, 수치계산 결과들은 이젝터 내부의 유동특성들을 조사하는데 이용되었다. 계산결과, 이젝터 압력비가 6 이상인 경우 이젝터 내부에서 발생하는 유동장은 이젝터 압력비에 크게 의존하지 않는다는 것을 알았다. 본 연구에서 사용된 단순 형태의 초음속 이젝터에 대하여, 2차 정체실의 압력은 이젝터 압력비가 6인 경우에 약 7k㎩로 최소로 되었다. 그러나 이젝터 압력비가 6이상으로 증가하는 경우 2차 정체실의 압력은 증가하는 것으로 나타났다. 이와 같은 2차 정체실의 압력증가는 1차 노즐로부터 방출되는 부족팽창 제트유동이 이젝터 벽면에 충돌함으로써 발생하는 재순환 유동으로 설명할 수 있었다.

• Advances in aircraft and spacecraft science
• /
• 제3권3호
• /
• pp.243-257
• /
• 2016

The increase of air traffic volume has brought an increasing amount of issues related to carbon and NOx emissions and noise pollution. Aircraft manufacturers are concentrating their efforts to develop technologies to increase aircraft efficiency and consequently to reduce pollutant discharge and noise emission. Ultra High By-Pass Ratio engine concepts provide reduction of fuel consumption and noise emission thanks to a decrease of the jet velocity exhausting from the engine nozzles. In order to keep same thrust, mass flow and therefore section of fan/nacelle diameter should be increased to compensate velocity reduction. Such feature will lead to close-coupled architectures for engine installation under the wing. A strong jet-wing interaction resulting in a change of turbulent mixing in the aeroacoustic field as well as noise enhancement due to reflection phenomena are therefore expected. On the other hand, pressure fluctuations on the wing as well as on the fuselage represent the forcing loads, which stress panels causing vibrations. Some of these vibrations are re-emitted in the aeroacoustic field as vibration noise, some of them are transmitted in the cockpit as interior noise. In the present work, the interaction between a jet and wing or fuselage is reproduced by a flat surface tangential to an incompressible jet at different radial distances from the nozzle axis. The change in the aerodynamic field due to the presence of the rigid plate was studied by hot wire anemometric measurements, which provided a characterization of mean and fluctuating velocity fields in the jet plume. Pressure fluctuations acting on the flat plate were studied by cavity-mounted microphones which provided point-wise measurements in stream-wise and spanwise directions. Statistical description of velocity and wall pressure fields are determined in terms of Fourier-domain quantities. Scaling laws for pressure auto-spectra and coherence functions are also presented.

• 설비공학논문집
• /
• 제12권1호
• /
• pp.59-66
• /
• 2000

In a previous paper, we have examined the effects of nozzle configuration and jet to jet spacing on the heat transfer of 1 row of circular water jets. In this paper, experiments have been conducted to obtain the effects of nozzle to target plate distances on the heat transfer of 1 row of 3 jets and 1 row of 5 jets. The nozzle configurations are Cone type, Reverse cone type and Vertical circular type. Nozzle to target plate distance H was varied from 16 mm(H/D=2) to 80mm(H/D=10). For fixed value of mass flow rate and nozzle to target plate distance, larger values of average Nusselt number were obtained for the smaller jet to jet spacing. For the array of water jets, the average heat transfer was decreased slightly with increasing nozzle to target plate distance at low jet velocity of $\textrm{V}_{o}$=3 m/s. However, except for $\textrm{V}_{o}$=8 m/s of 1 row of 5 jets, it was increased with increasing nozzle to target plate distance at high jet velocity of $\textrm{V}_{o}$$\geq$6m/s. We proposed to apply the nozzle configuration of maximum average heat transfer to each nozzle to target plate distance for 1 row of 3 jets, and, it was Reverse cone type nozzle for 1 row of 5 jets(Reynolds number$\geq$36000).

• Wind and Structures
• /
• 제29권1호
• /
• pp.75-84
• /
• 2019

A steady slot suction near the free-end leading edge of a finite-length square cylinder was used to control its aerodynamic forces and vortex-induced vibration (VIV). The freestream oncoming flow velocity ($U_{\infty}$) was from 3.8 m/s to 12.8 m/s. The width of the tested cylinder d = 40 mm and aspect ratio H/d = 5, where H was the height of the cylinder. The corresponding Reynolds number was from 10,400 to 35,000. The tested suction ratio Q, defined as the ratio of suction velocity ($U_s$) at the slot over the oncoming flow velocity at which the strongest VIV occurs ($U_{\nu}$), ranged from 0 to 3. It was found that the free-end slot suction can effectively attenuate the VIV of a cantilevered square cylinder. In the experiments, the RMS value of the VIV amplitude reduced quickly with Q increasing from 0 to 1, then kept approximately constant for $Q{\geq}1$. The maximum reduction of the VIV occurs at Q = 1, with the vibration amplitude reduced by 92%, relative to the uncontrolled case. Moreover, the overall fluctuation lift of the finite-length square cylinder was also suppressed with the maximum reduction of 87%, which occurred at Q = 1. It was interesting to discover that the free-end shear flow was sensitive to the slot suction near the leading edge. The turbulent kinetic energy (TKE) of the flow over the free end was the highest at Q = 1, which may result in the strongest mixing between the high momentum free-end shear flow and the near wake.

• Advances in aircraft and spacecraft science
• /
• 제6권3호
• /
• pp.239-256
• /
• 2019

This study develops a dual purpose: i) evaluating the effects of two different Mars atmosphere models (NASA Glenn and GRAM-2001) on aerodynamics of a capsule (Pathfinder) entering the Mars atmosphere, ii) verifying the feasibility of evaluating the ambient density and pressure by means of the methods by McLaughlin and Cassanto, respectively and therefore to re-build the values provided by the models. The method by McLaughlin relies on the evaluation of the capsule drag coefficient, the method by Cassanto relies on the measurement of pressure at a point on the capsule surface in aerodynamic shadow. The study has been carried out computationally by means of: i) a code integrating the equations of dynamics of the capsule for the computation of the entry trajectory, ii) a DSMC code for the solution of the flow field around the capsule in the altitude interval 50-100 km. The models show consistent differences at altitudes higher than about 40 km. It seems that the GRAM-2001 model is more reliable than the NASA Glenn model. In fact, the NASA Glenn model produces, at high altitude, temperatures that seem to be too low compared with those from the GRAM-2001 model and correspondingly very different aerodynamic conditions in terms of Mach, Reynolds and Knudsen numbers. This produces pretty different capsule drag coefficients by the two models as well as pressure on its surface, making not feasible neither the method by McLaughlin nor that by Cassanto, until a single, reliable model of the Mars atmosphere is not established. The present study verified that the implementation of the Cassanto method in Mars atmosphere should rely (such as it is currently) on pressure obtained experimentally in ground facilities.

• 한국수자원학회논문집
• /
• 제56권2호
• /
• pp.125-137
• /
• 2023

지속적으로 증가하는 플라스틱의 사용으로 인하여 현재 해안·해양 환경에서 플라스틱을 찾기란 어렵지 않은 일이 되었다. 하천을 통해 해양으로 유출된 플라스틱 폐기물은 해안 지역에서 장기간 머물며, 파랑, 바람, 유사, 인간 활동 등과 같은 다양한 요인들과 상호작용하며 물리적·화학적 변화를 겪게 된다. 이에, 실험적 연구를 통하여 해안 유사에서 수체로의 플라스틱 입자 방출 과정을 고찰하고자 하였다. 본 연구는 고 레이놀즈 수를 가지는 왕복 흐름과 유사 이동을 구현하기 위한 왕복흐름발생장치를 제작하여 진행되었고, 세 가지의 크기를 가지는 매끈한 구형의 플라스틱 입자를 사용하였다. 실험 결과, 유사 내 플라스틱 입자의 방출은 유사 이동에 가장 큰 영향을 받았으며, 이는 흐름의 세기에 비례한다. 더불어, 입자가 작을수록 더 많은 입자가 방출되었다. 결과를 종합하여 입자의 방출을 결정하는 무차원 매개변수들의 임계값을 제시하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1217-1224
• /
• 2014

This paper provides a practical scaling method to solve an old problem for scaling and developing the speed and resistance of a model to full-scale submarine in fully submerged underwater test. In every experimental test in towing tank, water tunnel and wind tunnel, in the first step, the speed of a model should be scaled to the full-scale vessel (ship or submarine). In the second step, the obtained resistance of the model should be developed. For submarine, there are two modes of movement: surface and submerged mode. There is no matter in surface mode because, according to Froude's law, the ratio of speed of the model to the full-scale vessel is proportional to the square root of lengths (length of the model on the length of the vessel). This leads to a reasonable speed and is not so much for the model that is applicable in the laboratory. The main problem is in submerged mode (fully submerged) that there isn't surface wave effect and therefore, Froude's law couldn't be used. Reynold's similarity is actually impossible to implement because it leads to very high speeds of the model that is impossible in a laboratory and inside the water. According to Reynold's similarity, the ratio of speed of the model to the full-scale vessel is proportional to the ratio of the full-scale length to the model length that leads to a too high speed. This paper proves that there is no need for exact Reynold's similarity because after a special Reynolds, resistance coefficient remains constant. Therefore, there is not compulsion for high speeds of the model. For proving this finding, three groups of results are presented: two cases are based on CFD method, and one case is based on the model test in towing tank. All these three results are presented for three different shapes that can show; this finding is independent of the shapes and geometries. For CFD method, Flow Vision software has been used.

• Korean Chemical Engineering Research
• /
• 제52권4호
• /
• pp.516-521
• /
• 2014

고점성이며 낮은 표면장력 매체로 구성된 기포탑에서 축방향 국부 열전달 계수와 총괄 열전달 계수에 대해 고찰하였다. 기체공탑유속(0.02~0.10 m/s), 액체 점도($0.1{\sim}0.3Pa{\cdot}s$) 그리고 액체 표면장력($66.1{\sim}72.9{\times}10^{-3}N/m$)이 국부 및 총괄 열전달 계수에 미치는 영향을 검토하였다. 열전달 영역은 기포탑 내부 열원과 기포탑 간의 열전달계로 구성하였다. 즉, 기포탑의 중앙에 수직 열원을 설치하여 내부 열원으로 하였다. 열전달 계수는 주어진 운전조건에서 열원에 제공되는 열량과 내부 열원과 기포탑 간의 온도차를 연속적으로 측정하여 결정하였다. 국부 열전달 계수는 기체공탑유속이 증가함에 따라 증가하였으나 기체 분산판으로 부터의 축방향 거리가 증가함에 따라, 액체의 표면장력이 증가함에 따라 감소하였다. 총괄 열전달 계수는 기체공탑유속이 증가함에 따라 증가하였으나 액상의 점도와 표면장력이 증가함에 따라서는 감소하였다. 총괄 열전달 계수는 기체공탑유속, 액상의 점도와 표면장력의 함수로 상관계수 0.91의 상관식을 얻을 수 있었으며 넛셀 수, 레이놀즈 수, 플란틀 수 그리고 웨버 수의 함수로 상관계수 0.92의 상관식으로 나타낼 수 있었다. $$h=2502U^{0.236}_{G}{\mu}^{-0.250}_{L}{\sigma}^{-0.028}_L$$ $$Nu=325Re^{0.180}Pr^{-0.067}We^{0.028}$$.

• 대한조선학회논문집
• /
• 제34권1호
• /
• pp.11-23
• /
• 1997

본 논문은 선박용 프로펠러 날개단면의 개발 과정을 다루고 있다. 2차원 날개단면의 유체역학적 특성은 캠버 및 두께 분포, 앞날 반경 등 기하학적 형상에 따라 달라진다. 2차원 날개단면 주위의 전 유장을 난류로 고려한 후 해석하기 위해 유한 체적법에 의한 Reynoles time averaged Navier-Stockes 방정식을 이용한 수치해석 기법을 개발하였다. 본 연구에서는 날개단aus 표면에 보다 많은 계산점을 주면서도 받음각의 변화에도 격자계 생성이 용이한 O-Type 격자계를 채택하였고, 전 유동장은 k-${\varepsilon}$ 난류 모형을 적용하여 해석하였다. 본 연구에서 개발된 수치해석 기법은 NACA0012의 실험 결과와 비교하여 계산 정도를 확인하였다. 본 연구에서는 낮은 항력을 갖는 고효율 날개단면 개발을 목표로, 항력이 양호한 날개단면은 공동 터널에서 양력, 항력 및 공동 특성 실험을 수행하였으며, 수치 해석 결과와도 비교하였다. 본 연구를 통하여 개발된 2차원 날개단면 해석용 수치 유체역학 코드는 실험 결과와 잘 일치하고 있음을 알 수 있었다. 이상의 과정을 통하여 기존의의 날개단면인 NACA66 두께 분포와 a=0.8 mean line 캠버를 갖는 KH13보다 효율뿐만 아니라 공동 특성도 우수한 단면인 KH28을 개발할 수 있었다. 새로운 날개 단면인 KH28은 선박용 프로펠러에 적용하기 위한 연구가 지속되어야 하며, 한편 낮은 받음각에서 양-항력 추정의 정확도를 높이기 위해서는 개발된 수치해석 코드에 2-경계층 모형이 적용되어야 할 것으로 본다.