• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.7
• /
• pp.7-15
• /
• 2008

A single active capacitor snubber-assisted soft-switching sinewave pulse modulation utility-interactive power conditioner with a three-winding flyback high frequency transformer link and a bidirectional active power switch in its secondary side has been proposed. With the aid of the switched-capacitor quasi-resonant snubber cell, the high frequency switching devices in the primary side of the proposed DC-to-AC sinewave power inverter can be turned-off with ZVS commutation. In addition to this, the proposed power conditioner in the DCM can effectively take the advantages of ZCS turn-on commutation. Its output port is connected directly to the utility AC power source grid. At the end, the prototype of the proposed HF-UPC is built and tested in experiment. Its power conversion conditioning and processing circuit with a high frequency flyback transformer link is verified and the output sinewave current is qualified in accordance with the power quality guidelines of the utility AC interactive power systems.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.4
• /
• pp.41-46
• /
• 2005

In this paper, a new method for suppressing microwelding on the RF MEMS (Radio Frequency Microelectromechanical System) direct contact switches is introduced. Two kinds of refractory metals, tungsten and molybdenum were coated onto the contact point of the switches and the effect of the coating was examined. The changes in insertion loss and isolation at the switch were measured by using network analyzer and power loss was evaluated by power measurement. The results revealed that while tungsten and molybdenum showed higher contact resistance than gold in low input power range, they enhanced the power handling capability and reliability of the switches in high input power region.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2126-2128
• /
• 2000

A TVS(triggered vacuum switch) use in high-power, high-current, and high-frequency conversion and switching circuits. The TVS has a six-gap trapezoidal rod electrode system. The electrode system consists of three cathode and anode rods which are made with OFHC. The trigger unit of the TVS is located at the cathode base center. To obtain a wide variety of characteristics this paper describes the results of tests.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.5
• /
• pp.502-507
• /
• 1999

An improved, accurate and reliable high-voltage measuring system utilizing a bushing-type capacitor is proposed in this study. This system measures voltages and phase angles of three-phase 22.9 kV power distribution lines and provides enough current to charge a battery for a motor-driven load switch and to operate the measuring and communication circuits for the distribution automation. For reliability, epoxy resin was used as the dielectric material of the bushing-type capacitor since the dielectric strength of epoxy resin is very stable over the wide range of temperature. Capacitances were investigated and found to be stable over the wide range of temperature and applied voltage, and the results indicate that the proposed measurement system is very reliable.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.337-340
• /
• 2007

In the dissertation, a power conversion system for fuel cell is composed of a PWM inverter with LC filter in order to convert fuel cell voltage to a single phase 220[V], In addition, new insulated DC-DC converters are proposed in order that fuel cell voltage is boosted to 380[V]. In this paper, it requires smaller components than existing converters, which makes easy control. The proposed DC-DC converter controls output power by the adjustment of phase-shift width using switch S5 and S6 in the secondary switch, which provides 93-97[%] efficiency in the wide range of output voltage. Fuel cell simulator is implemented to show similar output characteristics to actual fuel cell. Appropriate dead time td enables soft switching to the range where the peak value of excitation current in a high frequency transformer is in accordance with current in the primary circuit. Moreover, appropriate setting to serial inductance La reduces communication loss arisen at light-load generator and serge voltage arisen at a secondary switch and serial diode. Finally, TMS320C31 board and EPLD using PWM switching technique to act a single phase full-bridge inverter which is planed to make alternating current suitable for household.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.430-437
• /
• 2004

This thesis proposes novel SRP-PWM(Separately Random Pulse Position PWM) techniques and novel two-phase switching pattern applied to four-switch inverter, having various advantages such as operation time decrease that is required for decrease of switching damage, easy of implementation and inverter control at high frequency switching. In this thesis, we wish to confirm that SRP-PWM techniques disperse harmonic spectrum of inverter output current evenly into wide frequency area, that is, side-band of specification frequency. And we confirm the harmonic reduction effect of proposed techniques. Therefore, we will achieve an experiment by IGBT inverter using DSP and will verify the validity of proposed techniques compared with simulation results that use MATLAB/SIMULINK.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.330-333
• /
• 2002

The design of high power electronic circuits and the verification of the design by practical experiments are time and cost consuming. Recently power circuit simulation technique is developing to do it easily. However, most of the simulation has used the ideal switch model consists of passive component that can not describe the physical characteristics of semiconductor devices and cannot describe the switching transient state. For the design of such power electronic circuits by the simulation, the switching transients are very important. Therefore the simulation models must describe the switching transient and the stationary behavior as precisely as possible on the hand and as fast as possible the other hand. This paper introduces the application of the physical models of power devices that are developed by TUM(Technical University of Munich, Germany) for the power electronic circuit analysis.

• Journal of Power Electronics
• /
• v.13 no.4
• /
• pp.719-728
• /
• 2013

A novel hybrid active power filter (NHAPF) that can be adopted in high-voltage systems is proposed in this paper. The topological structure and filtering principle of the compensating system is provided and analyzed, respectively. Different controlling strategies are also presented to select the suitable strategy for the compensation system. Based on the selected strategy, the harmonic suppression function is used to analyze the influence of system parameters on the compensating system with MATLAB. Moreover, parameters in the injection branch are designed and analyzed. The performance of the proposed NHAPF in harmonic suppression and reactive power compensation is simulated with PSim. Thereafter, the overall control method is proposed. Simulation analysis and real experiments show that the proposed NHAPF exhibits good harmonic suppression and reactive power compensation. The proposed compensated system is based on the three-phase four-switch inverter, which is inexpensive, and the control method is verified for validity and effectiveness.

• Journal of IKEEE
• /
• v.14 no.2
• /
• pp.1-8
• /
• 2010

In this paper, Green Mode Power IC is designed to reduce the standby power. The proposed and designed IC works for the Switch Mode Power Supply(SMPS) and has the function of PWM. To reduce the unnecessary electric power, burst mode and skip mode section are introduced and controlled by external power MOSFET to diminish the standby power. The proposed IC is designed and simulated by KEC 30V-High Voltage 0.5um CMOS Process. The structure of proposed IC is composed of voltage regulator circuit, voltage reference circuit, UVLO(Under Voltage Lock out) circuit, Ibias circuit, green circuit, PWM circuit, OSC circuit, protection circuit, control circuit, and level & driver circuit. Measuring the current consumption of each block from the simulation results, 1.2942 mA of the summing consumption current from each block is calculated and ot proved that it is within the our design target of 1.3 mA. The current consumption of the proposed IC in this paper is less than a half of conventional ICs, and power consumption is reduced to the extent of 1W in standby mode. From the above results, we know that efficiency of proposed IC is superior to the previous IC.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.206-209
• /
• 2006

At present, the cold cathode fluorescent lamp (CCFL) using mercury lamp has been generally used far liquid crystal backlight source of personal computer and car navigation and so on. This kind of lamp is more excellent on luminance performance and cost. However, the requirements of liquid crystal backlight due to a light source without mercury have been strongly increased from a viewpoint of the actual influence on environmental preservation and environmental recycling. As fluorescent lamp without mercury, Dielectric Barrier Discharge based rare gas fluorescent lamp (DBD-FL) using xenon (Xe) gas has been studied so far. This DBD lamp has no influence on the human body and environmental recycle. Its operating life is long because electrode is out. In this paper, the simulation and experimental results of soft switching high frequency inverter with reverse blocking single switch as a high frequency power supply circuit for DBD-FL using Xe gas are comparatively evaluated and discussed from a practical point of view.